2007/6/26, Brad Campbell <[EMAIL PROTECTED]>:
Johny Mail list wrote:
> Hello list,
> I have a little question about software RAID on Linux.
> I have installed Software Raid on all my SC1425 servers DELL by
> believing that the md raid was a strong driver.
> And recently i make some test on a server and try to view if the RAID
> hard drive power failure work fine, so i power up my server and after
> booting and the prompt appear I disconnected the power cable of my
> SATA hard drive. Normaly the MD should eleminate the failure hard
> drive of the logical drive it build, and the server continue to work
> fine like nothing happen. Oddly the server stop to respond and i get
> this messages :
> ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> ata4.00: cmd e7/00:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x0 data 0
> res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata4: port is slow to respond, please be patient (Status 0xd0)
> ata4: port failed to respond (30sec, Status 0xd0)
> ata4: soft resetting port
>
> After that my system is frozen. Normaly in a basic RAID the device is
> "disable" in the logical RAID device (md0) and it only use the last
> disk.
cc to linux-ide added.
Unfortunately this is not an artifact of the linux raid driver, rather it
appears to be an issue
with the SATA driver and related error recovery. Some information about what
kernel, configuration,
drives, controller cards and other relevant system information would be good.
See the information at this URL for the sort of extra information that would be
handy.
http://www.kernel.org/pub/linux/docs/lkml/reporting-bugs.html
Regards,
Brad
--
"Human beings, who are almost unique in having the ability
to learn from the experience of others, are also remarkable
for their apparent disinclination to do so." -- Douglas Adams
Ok no problem.
I have a DELL SC1425 with a no card controler, only chipset for SATA
and FakeRAID (Intel Chipset and Adaptec for FakeRAID but i have
disable this function) :
00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE
Controller (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801EB (ICH5) SATA Controller (rev 02)
Specs of the server here :
http://www.dell.com/downloads/global/products/pedge/en/sc1425_specs.pdf
Hard Drivers are 2 S-ATA Model=WDC WD800JD-75LSA0.
I use , in my kernel configuration 2.6.21.5 :
- "ATA device support" (CONFIG_ATA)
-- "Intel ESB, ICH, PIIX3, PIIX4 PATA/SATA support" Driver (CONFIG_ATA_PIIX)
And get this messages during my boot :
[ 30.961007] libata version 2.20 loaded.
[ 31.867977] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 31.868037] ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
[ 31.868369] Probing IDE interface ide0...
[ 32.432715] Probing IDE interface ide1...
[ 32.995829] ata_piix 0000:00:1f.1: version 2.10ac1
[ 32.995843] PCI: Enabling device 0000:00:1f.1 (0000 -> 0003)
[ 32.995905] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level,
low) -> IRQ 18
[ 32.996027] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 32.996094] ata1: PATA max UDMA/133 cmd 0x00000000000101f0 ctl
0x00000000000103f6 bmdma 0x000000000001fc00 irq 14
[ 32.996213] ata2: PATA max UDMA/133 cmd 0x0000000000010170 ctl
0x0000000000010376 bmdma 0x000000000001fc08 irq 15
[ 32.996305] scsi0 : ata_piix
[ 32.996443] ata1: port disabled. ignoring.
[ 32.996467] scsi1 : ata_piix
[ 32.996582] ata2: port disabled. ignoring.
[ 32.996613] ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
[ 32.996858] ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level,
low) -> IRQ 18
[ 32.996977] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 32.997014] ata3: SATA max UDMA/133 cmd 0x000000000001ccb8 ctl
0x000000000001ccb2 bmdma 0x000000000001cc80 irq 18
[ 32.997125] ata4: SATA max UDMA/133 cmd 0x000000000001cca0 ctl
0x000000000001cc9a bmdma 0x000000000001cc88 irq 18
[ 32.997210] scsi2 : ata_piix
[ 33.167491] ata3.00: ATA-7: WDC WD800JD-75LSA0, 09.01D09, max UDMA/133
[ 33.167551] ata3.00: 156250000 sectors, multi 8: LBA48
[ 33.179467] ata3.00: configured for UDMA/133
[ 33.179527] scsi3 : ata_piix
[ 33.351130] ata4.00: ATA-7: WDC WD800JD-75LSA0, 09.01D09, max UDMA/133
[ 33.351190] ata4.00: 156250000 sectors, multi 8: LBA48
[ 33.363112] ata4.00: configured for UDMA/133
[ 33.363277] scsi 2:0:0:0: Direct-Access ATA WDC
WD800JD-75LS 09.0 PQ: 0 ANSI: 5
[ 33.363476] SCSI device sda: 156250000 512-byte hdwr sectors (80000 MB)
[ 33.363550] sda: Write Protect is off
[ 33.363606] sda: Mode Sense: 00 3a 00 00
[ 33.363635] SCSI device sda: write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 33.363770] SCSI device sda: 156250000 512-byte hdwr sectors (80000 MB)
[ 33.363843] sda: Write Protect is off
[ 33.363899] sda: Mode Sense: 00 3a 00 00
[ 33.363928] SCSI device sda: write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 33.364002] sda: sda1 sda2 sda3
[ 33.369982] sd 2:0:0:0: Attached scsi disk sda
[ 33.370118] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 33.370262] scsi 3:0:0:0: Direct-Access ATA WDC
WD800JD-75LS 09.0 PQ: 0 ANSI: 5
[ 33.370450] SCSI device sdb: 156250000 512-byte hdwr sectors (80000 MB)
[ 33.370524] sdb: Write Protect is off
[ 33.370580] sdb: Mode Sense: 00 3a 00 00
[ 33.370609] SCSI device sdb: write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 33.370729] SCSI device sdb: 156250000 512-byte hdwr sectors (80000 MB)
[ 33.370802] sdb: Write Protect is off
[ 33.370858] sdb: Mode Sense: 00 3a 00 00
[ 33.370886] SCSI device sdb: write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 33.370967] sdb: sdb1 sdb2
[ 33.375935] sd 3:0:0:0: Attached scsi disk sdb
[ 33.376068] sd 3:0:0:0: Attached scsi generic sg1 type 0
If you want all my .config, i can post it.
-
To unsubscribe from this list: send the line "unsubscribe linux-raid" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
