On Sun, Jul 6, 2014 at 8:15 AM, Hans de Goede <[email protected]> wrote: > Hi, > > On 07/04/2014 06:50 PM, [email protected] wrote: >> So is AP6210 support in mainline 3.16-rc1? I don't have a wireless >> device when I boot it but I do get some log messages at boot.... >> >> Can the AP6210 be probed? I don't see anything in the Cubietruck DTS >> loading the driver. >> >> This is on Emilio's DMA tree. >> http://git.elopez.com.ar/linux/commits/branch/sunxi-dma >> >> [ 1.809112] mmc1: new high speed SDIO card at address 0001 >> [ 1.815717] brcmfmac: F1 signature read @0x18000000=0x1591a962 >> [ 2.835866] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): >> clkctl 0x50 >> [ 3.856501] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): >> clkctl 0x50 > > This happens when your using a wrong nvram file / wrong > > brcmfmac43362-sdio.txt > > Where did you get yours from?
It is from cubieboard.org. Where is the correct one? #AP6210_NVRAM_V1.2_03192013 manfid=0x2d0 prodid=0x492 vendid=0x14e4 devid=0x4343 boardtype=0x0598 # Board Revision is P307, same nvram file can be used for P304, P305, P306 and P307 as the tssi pa params used are same #Please force the automatic RX PER data to the respective board directory if not using P307 board, for e.g. for P305 boards force the data into the following directory /projects/BCM43362/a1_labdata/boardtests/results/sdg_rev0305 boardrev=0x1307 boardnum=777 xtalfreq=26000 boardflags=0x80201 boardflags2=0x80 sromrev=3 wl0id=0x431b macaddr=00:90:4c:07:71:12 aa2g=1 ag0=2 maxp2ga0=74 cck2gpo=0x2222 ofdm2gpo=0x44444444 mcs2gpo0=0x6666 mcs2gpo1=0x6666 pa0maxpwr=56 #P207 PA params #pa0b0=5447 #pa0b1=-658 #pa0b2=-175<div></div> #Same PA params for P304,P305, P306, P307 pa0b0=5447 pa0b1=-607 pa0b2=-160 pa0itssit=62 pa1itssit=62 cckPwrOffset=5 ccode=0 rssismf2g=0xa rssismc2g=0x3 rssisav2g=0x7 triso2g=0 noise_cal_enable_2g=0 noise_cal_po_2g=0 swctrlmap_2g=0x04040404,0x02020202,0x02020202,0x010101,0x1ff temp_add=29767 temp_mult=425 btc_flags=0x6 btc_params0=5000 btc_params1=1000 btc_params6=63 > > Note that these files are board specific. So if some distro is > actually shipping these, please tell them to stop doing so, as > shipping these files is a BAD idea (since they are board specific). > > Regards, > > Hans > > -- > You received this message because you are subscribed to the Google Groups > "linux-sunxi" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > For more options, visit https://groups.google.com/d/optout. -- Jon Smirl [email protected] -- You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
