On 26 March 2015 at 19:17, Code Kipper <codekip...@gmail.com> wrote: > On 26 March 2015 at 18:41, ramanan vtm <vtm...@gmail.com> wrote: >> Thanks for the fast response! >> >> I've dd'ed the openwrt-sunxi-Cubietruck-sdcard-vfat-ext4.img onto the >> sdcard. After 'Starting kernel ...' the screen goes blank. I have the >> following files on the boot partition: boot.scr, dtb and uImage. Root >> partition has all the OpenWRT files. Now I'm playing around with the >> vEnv.txt file from the package/boot/uboot-sunxi folder, but no progress at >> all. >> >> Second last line goes like this: >> >> "Using Device tree in place at 43000000, end 430090e5 >> Cannot setup simplefb: node not found" > I've never used openwrt with a monitor. I'm not sure if the kernel > version currently used supports > simplefb. I'll check the config file from my build later on, You may > need to make kernel_menuconfig > and enable simple fb. Just to confirm Simple Frame buffer went into linux-3.19 so openwrt with a monitor isn't possible. You will have to do everything via serial until you can telnet or ssh into the device. CK > My working scenarios have always been booting from sdcard and logging > with the uart. Then I was > able to set up the network connections and eventually my wireless > device. I've not had the need to > go much further than that. > wingrime on irc is the guy upstreaming the sunxi patches for openwrt. > See if he's online. > BR, > CK >> >> I've tried the instructions at >> http://wiki.openwrt.org/doc/hardware/soc/soc.allwinner.sunxi#sd_preparation...bootloader >> keeps looking for pxelinux.cfg and halts at sun7i# prompt. Have not access >> to keyboard to go any further. >> >> How would I access the log files? >> >> On Wednesday, March 25, 2015 at 4:30:59 AM UTC-4, CodeKipper wrote: >>> >>> On 24 March 2015 at 21:12, ramanan vtm <vtm...@gmail.com> wrote: >>> > Hello, >>> > >>> > I successfully compiled the OpenWRT trunk Rev:44951. Uboot starts from >>> > SSD. >>> > However, it hangs at 'Starting kernel ...' message for a few seconds and >>> > everything dies out. >>> > >>> > I'm sure it's because the kernel is not loading properly...I probably >>> > have >>> > to update the correct Load Address and Entry Point. I've been stuck with >>> > it >>> > for a while. >>> > >>> > Would appreciate any help. >>> > >>> > Thanks >>> > -vtmr >>> >>> Hi, >>> have you tried the files here? >>> https://downloads.openwrt.org/snapshots/trunk/sunxi/generic/ >>> and the sdcard setup here? >>> >>> http://wiki.openwrt.org/doc/hardware/soc/soc.allwinner.sunxi#sd_preparation. >>> These have worked for me in the past. Sounds like uEnv.txt and boot.scr >>> are >>> missing. Some logs would help. >>> BR, >>> CK >>> > >>> > -- >>> > You received this message because you are subscribed to the Google >>> > Groups >>> > "linux-sunxi" group. >>> > To unsubscribe from this group and stop receiving emails from it, send >>> > an >>> > email to linux-sunxi...@googlegroups.com. >>> > For more options, visit https://groups.google.com/d/optout. >> >> -- >> You received this message because you are subscribed to the Google Groups >> "linux-sunxi" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to linux-sunxi+unsubscr...@googlegroups.com. >> For more options, visit https://groups.google.com/d/optout.
-- You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscr...@googlegroups.com. For more options, visit https://groups.google.com/d/optout.
