Anyone else seen
ftape-io.c (ftape_report_error) - errorcode: 31.
ftape-io.c (ftape_set_data_rate) - Rate change failed!.
with zftape for ftape v4.03-pre-3 03/28/99 on 2.2.6-ac1 ?
This is a HP T1000 and works fine on previous ftape releases and 2.0.36.
With full tracing on, here are a few highlights:-
ftape v4.03-pre-3 03/28/99
(c) 1993-1996 Bas Laarhoven
(c) 1995-1996 Kai Harrekilde-Petersen
(c) 1996-1998 Claus-Justus Heine ([EMAIL PROTECTED])
QIC-117 driver for QIC-40/80/3010/3020/Ditto 2GB/MAX floppy tape drives.
Compiled for Linux version 2.2.6-ac1
installing QIC-117 floppy tape hardware drive ...
ftape_init @ 0xc284e220.
fdc-isr.c (handle_fdc_reset) - st0=c0, i=0.
fdc-isr.c (handle_fdc_reset) - st0=c1, i=1.
fdc-isr.c (handle_fdc_reset) - st0=c2, i=2.
fdc-isr.c (handle_fdc_reset) - st0=c3, i=3
fdc-isr.c (handle_fdc_reset) - drive polling completed.
fdc-io.c (fdc_probe) - Type 82077AA FDC found.
fdc-io.c (fdc_update_dsr) - rate = 500 Kbps, precomp = 0 ns.
[snip]
ftape-io.c (ftape_report_vendor_id) - got 16 bit id: 11c5.
ftape-ctl.c (ftape_log_vendor_id) - tape drive type: HP Colorado T1000.
ftape-ctl.c (ftape_init_drive) - post QIC-117B drive @ 500 Kbps.
+ftape-ctl.c (ftape_calibrate_data_rate)
fdc-io.c (fdc_update_dsr) - rate = 1000 Kbps, precomp = 0 ns.
ftape-ctl.c (ftape_calibrate_data_rate) - Highest FDC supported data rate: 1000 Kbps.
...
ftape-io.c (ftape_parameter) - called with parameter = 3.
ftape-io.c (ftape_set_data_rate) - error status set.
ftape-io.c (ft_check_cmd_restrictions) - report error code.
ftape-io.c (ftape_report_error) - errorcode: 31.
ftape-io.c (ftape_report_error) - Fatal ERROR:.
ftape-io.c (ftape_report_error) - Rate or Format Selection Error ....
ftape-io.c (ftape_report_error) - ... caused by command 'select rate or format'.
ftape-io.c (ft_check_cmd_restrictions) - report drive configuration.
ftape-io.c (ft_check_cmd_restrictions) - report tape status.
ftape-io.c (ftape_report_configuration) - report tape status result = 21.
ftape-io.c (ftape_set_data_rate) - Rate change failed!
[blah]
======================================================================
However, the CMOS backup battery on the target machine failed recently, and I
did have to set up all the BIOS parameters again. It is possible, but unlikely,
that I have changed an io timing value. I mention that just in case.
=======================================================================
Of course I will report in much more detail, probably directly to Claus
if need be.
Anyone else had trouble with 2.2.6 on a standard internal drive?
TIA
Adrian
--
A E Lawrence, MA., DPhil. [EMAIL PROTECTED]
MicroProcessor Unit, 13, Banbury Road, Oxford. OX2 6NN. UK.
Voice: (+44)-1865-273274, Fax: (+44)-1865-273275
