hi all, i've recently updated to kernel-2.6.7 from 2.4.25, i'm having some problems with my digital camera.. it's a nikon coolpix 4300, it was working with no problems at all under a 2.4 kernel. i think i've compiled all needed modules (i'm pretty sure about it) but since the upgrade i can't access the camera anymore.. i'm pasting here the interesting lines from dmesg, hope that someone can help me finding out what the problem is. please cc: me since i'm not subscribed to the list.
regards, riccardo
Jun 28 10:08:23 ricpersi usbcore: registered new driver usb-storage Jun 28 10:08:23 ricpersi USB Mass Storage support registered. Jun 28 10:09:34 ricpersi ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) Jun 28 10:09:34 ricpersi ohci_hcd: block sizes: ed 64 td 64 Jun 28 10:09:34 ricpersi ohci_hcd 0000:00:01.2: Silicon Integrated Systems [SiS] USB 1.0 Controller Jun 28 10:09:34 ricpersi ohci_hcd 0000:00:01.2: irq 10, pci mem d008e000 Jun 28 10:09:34 ricpersi ohci_hcd 0000:00:01.2: new USB bus registered, assigned bus number 1 Jun 28 10:09:34 ricpersi hub 1-0:1.0: USB hub found Jun 28 10:09:34 ricpersi hub 1-0:1.0: 2 ports detected Jun 28 10:09:35 ricpersi usb 1-2: new full speed USB device using address 2 Jun 28 10:09:35 ricpersi scsi1 : SCSI emulation for USB Mass Storage devices Jun 28 10:09:35 ricpersi Vendor: NIKON Model: NIKON DSC E4300 Rev: 1.00 Jun 28 10:09:35 ricpersi Type: Direct-Access ANSI SCSI revision: 02 Jun 28 10:09:35 ricpersi SCSI device sda: 253952 512-byte hdwr sectors (130 MB) Jun 28 10:09:35 ricpersi sda: assuming Write Enabled Jun 28 10:09:35 ricpersi sda: assuming drive cache: write through Jun 28 10:09:35 ricpersi sda:SCSI error : <1 0 0 0> return code = 0x70000 Jun 28 10:09:35 ricpersi end_request: I/O error, dev sda, sector 0 Jun 28 10:09:35 ricpersi Buffer I/O error on device sda, logical block 0 Jun 28 10:09:35 ricpersi SCSI error : <1 0 0 0> return code = 0x70000 Jun 28 10:09:35 ricpersi end_request: I/O error, dev sda, sector 0 Jun 28 10:09:35 ricpersi Buffer I/O error on device sda, logical block 0 Jun 28 10:09:35 ricpersi unable to read partition table Jun 28 10:09:35 ricpersi Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0 Jun 28 10:09:35 ricpersi USB Mass Storage device found at 2 Jun 28 10:09:36 ricpersi hub 1-0:1.0: port 2 disabled by hub (EMI?), re-enabling...<6>usb 1-2: USB disconnect, address 2 Jun 28 10:09:36 ricpersi usb 1-2: new full speed USB device using address 3 Jun 28 10:09:38 ricpersi scsi2 : SCSI emulation for USB Mass Storage devices Jun 28 10:09:38 ricpersi Vendor: NIKON Model: NIKON DSC E4300 Rev: 1.00 Jun 28 10:09:38 ricpersi Type: Direct-Access ANSI SCSI revision: 02 Jun 28 10:09:38 ricpersi SCSI device sda: 253952 512-byte hdwr sectors (130 MB) Jun 28 10:09:38 ricpersi sda: assuming Write Enabled Jun 28 10:09:38 ricpersi sda: assuming drive cache: write through Jun 28 10:09:38 ricpersi sda: sda1 Jun 28 10:09:38 ricpersi Attached scsi removable disk sda at scsi2, channel 0, id 0, lun 0 Jun 28 10:09:38 ricpersi USB Mass Storage device found at 3 Jun 28 10:10:21 ricpersi SCSI error : <2 0 0 0> return code = 0x70000 Jun 28 10:10:21 ricpersi end_request: I/O error, dev sda, sector 32 Jun 28 10:10:21 ricpersi Buffer I/O error on device sda1, logical block 0 Jun 28 10:10:21 ricpersi SCSI error : <2 0 0 0> return code = 0x70000 Jun 28 10:10:21 ricpersi end_request: I/O error, dev sda, sector 40 Jun 28 10:10:21 ricpersi Buffer I/O error on device sda1, logical block 1 Jun 28 10:10:21 ricpersi SCSI error : <2 0 0 0> return code = 0x70000 Jun 28 10:10:21 ricpersi end_request: I/O error, dev sda, sector 48 Jun 28 10:10:21 ricpersi Buffer I/O error on device sda1, logical block 2 Jun 28 10:10:21 ricpersi SCSI error : <2 0 0 0> return code = 0x70000 Jun 28 10:10:21 ricpersi end_request: I/O error, dev sda, sector 56
