Yes, I had noticed this. Only one order of driver/device works -- I
think(?!) I have to plug in the device and then insmod the driver for it to
work, otherwise it doesn't find the firmware properly -- I have not checked
the effect of booting on it. It seems to work fine with either of the two
uhci drivers. I am giving it a stress test (by using it extensively) at the
moment.
Richard
On 7 Jun, Steve Pacenka wrote:
> When I was using the Kaweth 0.2 driver patched to recognize a 3Com network
> device, I had to experiment with the order of boot, plug in device, and load
> kaweth module. Sometimes the device would be recognized and the firmware
> would download but the startup would fail, as it is failing for you.
>
> Possible orders:
>
> 1. Boot without device, insmod module manually, plug in device.
>
> 2. Boot with device plugged in, insmod module manually.
>
> 3. Boot without device, plug in device, insmod module manually.
>
> (Can't remember which of these actually worked :^) )
>
> -- SP
>
>
>
>
>> -----Original Message-----
>> From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]
>> Sent: Monday, June 05, 2000 5:56 PM
>> To: [EMAIL PROTECTED]
>> Cc: [EMAIL PROTECTED]
>> Subject: Re: [linux-usb] Kaweth driver
>>
>>
>> So, I tried version 0.2.1 of the Kawasaki-ethernet driver
>> with my D-Link
>> DSB-650. Definite progress, but apparently no cigar. The
>> device still does
>> not actually work. Good progress guys, I live in hope!
>>
>> Richard Melrose
>>
>> /proc/bus/usb/devices: (extension hub and mouse + D-Link)
>>
>> T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
>> B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
>> D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
>> P: Vendor=0000 ProdID=0000 Rev= 0.00
>> S: Product=USB UHCI Root Hub
>> S: SerialNumber=fce0
>> C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
>> I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
>> E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms
>> T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 7
>> D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
>> P: Vendor=0451 ProdID=1446 Rev= 1.00
>> C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
>> I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
>> E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=255ms
>> T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=1.5 MxCh= 0
>> D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
>> P: Vendor=0461 ProdID=4d04 Rev= 4.41
>> C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=100mA
>> I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=02 Driver=hid
>> E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl= 10ms
>> T: Bus=01 Lev=02 Prnt=02 Port=06 Cnt=02 Dev#= 4 Spd=12 MxCh= 0
>> D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
>> P: Vendor=0557 ProdID=2002 Rev= 0.02
>> S: Manufacturer=ATEN Inc.
>> S: Product=USB-Ethernet
>> S: SerialNumber=00107400278D
>> C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr= 90mA
>> I: If#= 0 Alt= 0 #EPs= 3 Cls=00(>ifc ) Sub=00 Prot=00 Driver=kaweth
>> E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl= 0ms
>> E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl= 0ms
>> E: Ad=83(I) Atr=03(Int.) MxPS= 8 Ivl= 1ms
>>
>> dmesg output on plugging the device into the extension hub,
>> using usb-uhci, after
>> loading kaweth.o:
>>
>> hub.c: port 7 connection change
>> hub.c: portstatus 101, change 1, 12 Mb/s
>> hub.c: portstatus 103, change 10, 12 Mb/s
>> usb.c: USB new device connect, assigned device number 4
>> usb.c: kmalloc IF c2f88cc0, numif 1
>> usb.c: new device strings: Mfr=2, Product=3, SerialNumber=1
>> usb.c: USB device number 4 default language ID 0x409
>> Manufacturer: ATEN Inc.
>> Product: USB-Ethernet
>> SerialNumber: 00107400278D
>> Kawasaki Device Probe (Device number:4): 0x0557:0x2002
>> Device at c7390ec0
>> Descriptor length: 12 type: 1
>> D-Link DSB-650 connected...
>> Reading kaweth configuration
>> Request type: c0 Request: 0 Value: 0 Index: 0 Length: 12
>> usb-uhci.c: interrupt, status 2, frame# 337
>> kaweth control message failed (urb addr: c5839d40)
>> Actual length: 0, length 18
>> Resetting...
>> Downloading firmware at c881c098 to kaweth device at c34ba000...
>> Firmware length: 3838
>> Request type: 40 Request: ff Value: 0 Index: 0 Length: efe
>> Actual length: 3838, length 3838
>> Downloading firmware at c881cf96 to kaweth device at c34ba000...
>> Firmware length: 720
>> Request type: 40 Request: ff Value: 0 Index: 0 Length: 2d0
>> Actual length: 720, length 720
>> Triggering firmware
>> Request type: 40 Request: ff Value: 0 Index: 0 Length: 8
>> Actual length: 8, length 8
>> Resetting device (jiffies: 19072b)...
>> Reset device (jiffies: 19072d)...
>> Reading kaweth configuration
>> Request type: c0 Request: 0 Value: 0 Index: 0 Length: 12
>> Actual length: 18, length 18
>> Statitstics collection: 0
>> Multicast filter limit: 80
>> MTU: 5ea
>> Read MAC address 00:10:74:00:27:8d
>> :12::00::00::00::10::74::00::27::8d::00::00::00::00::ea::05::8
>> 0::00::00:
>> Setting URB size to 1664
>> Request type: 40 Request: 8 Value: 680 Index: 0 Length: 0
>> Actual length: 0, length 0
>> Set SOFS wait to 5
>> Request type: 40 Request: 9 Value: 5 Index: 0 Length: 0
>> Actual length: 0, length 0
>> Set recieve filter to 28
>> Request type: 40 Request: 2 Value: 1c Index: 0 Length: 0
>> Actual length: 0, length 0
>> Initializing net device...
>> kaweth interface created at eth0
>> Kaweth probe returning...
>> usb.c: kaweth driver claimed interface c2f88cc0
>> Dev usage: 1
>> Opening network device...
>> Setting Rx mode
>> Failed to set Rx mode: -16
>> Setting Rx mode
>> Failed to set Rx mode: -16
>> Setting Rx mode
>> Failed to set Rx mode: -16
>> Setting Rx mode
>> Failed to set Rx mode: -16
>> Dev usage: 1
>> Dev usage: 1
>> Opening network device...
>> Setting Rx mode
>> Failed to set Rx mode: -16
>> Setting Rx mode
>> Failed to set Rx mode: -16
>> Setting Rx mode
>> Failed to set Rx mode: -16
>> Dev usage: 1
>> Dev usage: 1
>> Opening network device...
>> Setting Rx mode
>> Failed to set Rx mode: -16
>> Setting Rx mode
>> Failed to set Rx mode: -16
>> Setting Rx mode
>> Failed to set Rx mode: -16
>> Dev usage: 1
>> Dev usage: 1
>> Opening network device...
>> Setting Rx mode
>> Failed to set Rx mode: -16
>> Setting Rx mode
>> Failed to set Rx mode: -16
>>
>>
>>
>>
>>
>>
>> ---------------------------------------------------------------------
>> To unsubscribe, e-mail: [EMAIL PROTECTED]
>> For additional commands, e-mail: [EMAIL PROTECTED]
>>
>
---------------------------------------------------------------------
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]
