On Sat, 2009-01-10 12:28:24 +0100, Konstantin Nebel <[email protected]> wrote: > Hi, > > ich habe ein 3ware 8506-4LP Raid Controller mit einem Raid-5 am Laufen. Ich > höre ab und an fehlergeräusche von einer der Festplatten. Meiner Meinung nach > sehe ich aber nichts in Smart, was auf einen Defekt hinweist. Hier die > Auszüge > den 3 Pladden. Vielleicht seht ihr den Fehler. > > smartctl version 5.38 [x86_64-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen > Home page is http://smartmontools.sourceforge.net/ > > === START OF INFORMATION SECTION === > Model Family: SAMSUNG SpinPoint P120 series > Device Model: SAMSUNG SP2504C > Serial Number: 301012FP432889 > Firmware Version: VT100-59 > User Capacity: 250.059.350.016 bytes > Device is: In smartctl database [for details use: -P show] > ATA Version is: 7 > ATA Standard is: ATA/ATAPI-7 T13 1532D revision 4a > Local Time is: Sat Jan 10 12:15:35 2009 CET > > ==> WARNING: May need -F samsung3 enabled; see manual for details. > > SMART support is: Available - device has SMART capability. > SMART support is: Enabled > > === START OF READ SMART DATA SECTION === > SMART overall-health self-assessment test result: PASSED > > General SMART Values: > Offline data collection status: (0x02) Offline data collection activity > was completed without error. > Auto Offline Data Collection: Disabled. > Self-test execution status: ( 0) The previous self-test routine > completed > without error or no self-test has ever > been run. > Total time to complete Offline > data collection: (5066) seconds. > Offline data collection > capabilities: (0x5b) SMART execute Offline immediate. > Auto Offline data collection on/off > support. > Suspend Offline collection upon new > command. > Offline surface scan supported. > Self-test supported. > No Conveyance Self-test supported. > Selective Self-test supported. > SMART capabilities: (0x0003) Saves SMART data before entering > power-saving mode. > Supports SMART auto save timer. > Error logging capability: (0x01) Error logging supported. > General Purpose Logging supported. > Short self-test routine > recommended polling time: ( 1) minutes. > Extended self-test routine > recommended polling time: ( 84) minutes. > SCT capabilities: (0x003f) SCT Status supported. > SCT Feature Control supported. > SCT Data Table supported. > > SMART Attributes Data Structure revision number: 16 > Vendor Specific SMART Attributes with Thresholds: > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED > WHEN_FAILED RAW_VALUE > 1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always > - 0 > 3 Spin_Up_Time 0x0007 253 253 025 Pre-fail Always > - 5824 > 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always > - 92 > 5 Reallocated_Sector_Ct 0x0033 253 253 010 Pre-fail Always > - 0 > 7 Seek_Error_Rate 0x000f 253 253 051 Pre-fail Always > - 0 > 8 Seek_Time_Performance 0x0025 253 253 015 Pre-fail Offline > - 0 > 9 Power_On_Hours 0x0032 100 100 000 Old_age Always > - 3032 > 10 Spin_Retry_Count 0x0033 253 253 051 Pre-fail Always > - 0 > 11 Calibration_Retry_Count 0x0012 253 253 000 Old_age Always > - 0 > 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always > - 83 > 187 Reported_Uncorrect 0x0032 253 253 000 Old_age Always > - 196608 ^^^^^^ > 190 Airflow_Temperature_Cel 0x0022 109 094 000 Old_age Always > - 43 > 194 Temperature_Celsius 0x0022 109 094 000 Old_age Always > - 43 > 195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always > - 25285952 > 196 Reallocated_Event_Count 0x0032 253 253 000 Old_age Always > - 0 > 197 Current_Pending_Sector 0x0012 253 253 000 Old_age Always > - 0 > 198 Offline_Uncorrectable 0x0030 253 253 000 Old_age Offline > - 0 > 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always > - 0 > 200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always > - 0 > 201 Soft_Read_Error_Rate 0x000a 100 100 000 Old_age Always > - 0 > 202 TA_Increase_Count 0x0032 253 253 000 Old_age Always > - 0 > > SMART Error Log Version: 1 > No Errors Logged > > SMART Self-test log structure revision number 1 > Num Test_Description Status Remaining LifeTime(hours) > LBA_of_first_error > # 1 Extended offline Completed without error 00% 2793 - > # 2 Extended offline Interrupted (host reset) 70% 2346 - > # 3 Extended offline Completed without error 00% 1417 - > # 4 Extended offline Completed without error 00% 643 - > # 5 Extended offline Completed without error 00% 360 - > # 6 Extended offline Completed without error 00% 245 - > > SMART Selective Self-Test Log Data Structure Revision Number (0) should be 1 > SMART Selective self-test log data structure revision number 0 > Warning: ATA Specification requires selective self-test log data structure > revision number = 1 > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS > 1 0 0 Not_testing > 2 0 0 Not_testing > 3 0 0 Not_testing > 4 0 0 Not_testing > 5 0 0 Not_testing > Selective self-test flags (0x0): > After scanning selected spans, do NOT read-scan remainder of disk. > If Selective self-test is pending on power-up, resume after 0 minute delay. > > ______________________________________ > > > smartctl version 5.38 [x86_64-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen > Home page is http://smartmontools.sourceforge.net/ > > === START OF INFORMATION SECTION === > Model Family: SAMSUNG SpinPoint P120 series > Device Model: SAMSUNG SP2504C > Serial Number: S09QJ1GL302662 > Firmware Version: VT100-33 > User Capacity: 250.059.350.016 bytes > Device is: In smartctl database [for details use: -P show] > ATA Version is: 7 > ATA Standard is: ATA/ATAPI-7 T13 1532D revision 4a > Local Time is: Sat Jan 10 12:15:51 2009 CET > > ==> WARNING: May need -F samsung3 enabled; see manual for details. > > SMART support is: Available - device has SMART capability. > SMART support is: Enabled > > === START OF READ SMART DATA SECTION === > SMART overall-health self-assessment test result: PASSED > > General SMART Values: > Offline data collection status: (0x82) Offline data collection activity > was completed without error. > Auto Offline Data Collection: Enabled. > Self-test execution status: ( 0) The previous self-test routine > completed > without error or no self-test has ever > been run. > Total time to complete Offline > data collection: (4806) seconds. > Offline data collection > capabilities: (0x5b) SMART execute Offline immediate. > Auto Offline data collection on/off > support. > Suspend Offline collection upon new > command. > Offline surface scan supported. > Self-test supported. > No Conveyance Self-test supported. > Selective Self-test supported. > SMART capabilities: (0x0003) Saves SMART data before entering > power-saving mode. > Supports SMART auto save timer. > Error logging capability: (0x01) Error logging supported. > General Purpose Logging supported. > Short self-test routine > recommended polling time: ( 1) minutes. > Extended self-test routine > recommended polling time: ( 80) minutes. > > SMART Attributes Data Structure revision number: 16 > Vendor Specific SMART Attributes with Thresholds: > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED > WHEN_FAILED RAW_VALUE > 1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always > - 10 > 3 Spin_Up_Time 0x0007 100 100 025 Pre-fail Always > - 6016 > 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always > - 689 > 5 Reallocated_Sector_Ct 0x0033 077 077 010 Pre-fail Always > - 219 > 7 Seek_Error_Rate 0x000f 253 253 051 Pre-fail Always > - 0 > 8 Seek_Time_Performance 0x0025 253 253 015 Pre-fail Offline > - 0 > 9 Power_On_Hours 0x0032 100 100 000 Old_age Always > - 17874 > 10 Spin_Retry_Count 0x0033 253 253 051 Pre-fail Always > - 0 > 11 Calibration_Retry_Count 0x0012 253 002 000 Old_age Always > - 0 > 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always > - 663 > 190 Airflow_Temperature_Cel 0x0022 115 082 000 Old_age Always > - 41 > 194 Temperature_Celsius 0x0022 115 082 000 Old_age Always > - 41 > 195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always > - 17806828 > 196 Reallocated_Event_Count 0x0032 077 077 000 Old_age Always > - 219 > 197 Current_Pending_Sector 0x0012 253 253 000 Old_age Always > - 0 > 198 Offline_Uncorrectable 0x0030 253 253 000 Old_age Offline > - 0 > 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always > - 0 > 200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always > - 0 > 201 Soft_Read_Error_Rate 0x000a 100 100 000 Old_age Always > - 0 > 202 TA_Increase_Count 0x0032 253 253 000 Old_age Always > - 0 > > SMART Error Log Version: 1 > No Errors Logged > > SMART Self-test log structure revision number 1 > Num Test_Description Status Remaining LifeTime(hours) > LBA_of_first_error > # 1 Extended offline Completed without error 00% 17638 - > # 2 Extended offline Interrupted (host reset) 20% 17352 - > # 3 Extended offline Completed without error 00% 16277 - > # 4 Extended offline Completed without error 00% 15985 - > # 5 Extended offline Completed without error 00% 15502 - > # 6 Extended offline Completed without error 00% 15223 - > # 7 Extended offline Completed without error 00% 15108 - > # 8 Extended offline Completed without error 00% 14615 - > # 9 Extended offline Completed without error 00% 14469 - > #10 Extended offline Completed without error 00% 14202 - > #11 Extended offline Completed without error 00% 14171 - > > SMART Selective Self-Test Log Data Structure Revision Number (0) should be 1 > SMART Selective self-test log data structure revision number 0 > Warning: ATA Specification requires selective self-test log data structure > revision number = 1 > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS > 1 0 0 Not_testing > 2 0 0 Not_testing > 3 0 0 Not_testing > 4 0 0 Not_testing > 5 0 0 Not_testing > Selective self-test flags (0x0): > After scanning selected spans, do NOT read-scan remainder of disk. > If Selective self-test is pending on power-up, resume after 0 minute delay. > > ______________________________________ > > smartctl version 5.38 [x86_64-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen > Home page is http://smartmontools.sourceforge.net/ > > === START OF INFORMATION SECTION === > Model Family: SAMSUNG SpinPoint P120 series > Device Model: SAMSUNG SP2504C > Serial Number: S09QJ1GL302666 > Firmware Version: VT100-33 > User Capacity: 250.059.350.016 bytes > Device is: In smartctl database [for details use: -P show] > ATA Version is: 7 > ATA Standard is: ATA/ATAPI-7 T13 1532D revision 4a > Local Time is: Sat Jan 10 12:15:57 2009 CET > > ==> WARNING: May need -F samsung3 enabled; see manual for details. > > SMART support is: Available - device has SMART capability. > SMART support is: Enabled > > === START OF READ SMART DATA SECTION === > SMART overall-health self-assessment test result: PASSED > > General SMART Values: > Offline data collection status: (0x82) Offline data collection activity > was completed without error. > Auto Offline Data Collection: Enabled. > Self-test execution status: ( 0) The previous self-test routine > completed > without error or no self-test has ever > been run. > Total time to complete Offline > data collection: (4836) seconds. > Offline data collection > capabilities: (0x5b) SMART execute Offline immediate. > Auto Offline data collection on/off > support. > Suspend Offline collection upon new > command. > Offline surface scan supported. > Self-test supported. > No Conveyance Self-test supported. > Selective Self-test supported. > SMART capabilities: (0x0003) Saves SMART data before entering > power-saving mode. > Supports SMART auto save timer. > Error logging capability: (0x01) Error logging supported. > General Purpose Logging supported. > Short self-test routine > recommended polling time: ( 1) minutes. > Extended self-test routine > recommended polling time: ( 80) minutes. > > SMART Attributes Data Structure revision number: 16 > Vendor Specific SMART Attributes with Thresholds: > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED > WHEN_FAILED RAW_VALUE > 1 Raw_Read_Error_Rate 0x000f 100 099 051 Pre-fail Always > - 163 > 3 Spin_Up_Time 0x0007 100 100 025 Pre-fail Always > - 5952 > 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always > - 692 > 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always > - 1 > 7 Seek_Error_Rate 0x000f 253 253 051 Pre-fail Always > - 0 > 8 Seek_Time_Performance 0x0025 253 253 015 Pre-fail Offline > - 0 > 9 Power_On_Hours 0x0032 100 100 000 Old_age Always > - 17893 > 10 Spin_Retry_Count 0x0033 253 253 051 Pre-fail Always > - 0 > 11 Calibration_Retry_Count 0x0012 100 002 000 Old_age Always > - 33 ^^ > 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always > - 666 > 190 Airflow_Temperature_Cel 0x0022 121 082 000 Old_age Always > - 39 > 194 Temperature_Celsius 0x0022 121 082 000 Old_age Always > - 39 > 195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always > - 44236889 > 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always > - 1 > 197 Current_Pending_Sector 0x0012 253 100 000 Old_age Always > - 0 > 198 Offline_Uncorrectable 0x0030 253 253 000 Old_age Offline > - 0 > 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always > - 0 > 200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always > - 0 > 201 Soft_Read_Error_Rate 0x000a 100 100 000 Old_age Always > - 0 > 202 TA_Increase_Count 0x0032 253 253 000 Old_age Always > - 0 > > SMART Error Log Version: 1 > No Errors Logged > > SMART Self-test log structure revision number 1 > Num Test_Description Status Remaining LifeTime(hours) > LBA_of_first_error > # 1 Extended offline Completed without error 00% 17657 - > # 2 Extended offline Interrupted (host reset) 40% 17361 - > # 3 Extended offline Completed without error 00% 16457 - > # 4 Extended offline Completed without error 00% 16288 - > # 5 Extended offline Completed without error 00% 15997 - > # 6 Extended offline Completed without error 00% 15514 - > # 7 Extended offline Completed without error 00% 15235 - > # 8 Extended offline Completed without error 00% 15120 - > # 9 Extended offline Completed without error 00% 14627 - > #10 Extended offline Completed without error 00% 14481 - > #11 Extended offline Completed without error 00% 14210 - > #12 Extended offline Completed without error 00% 14182 - > > SMART Selective Self-Test Log Data Structure Revision Number (0) should be 1 > SMART Selective self-test log data structure revision number 0 > Warning: ATA Specification requires selective self-test log data structure > revision number = 1 > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS > 1 0 0 Not_testing > 2 0 0 Not_testing > 3 0 0 Not_testing > 4 0 0 Not_testing > 5 0 0 Not_testing > Selective self-test flags (0x0): > After scanning selected spans, do NOT read-scan remainder of disk. > If Selective self-test is pending on power-up, resume after 0 minute delay. > > Hier noch der Auszug aus dem Raid-Controller: > > Unit UnitType Status %RCmpl %V/I/M Stripe Size(GB) Cache AVrfy > ------------------------------------------------------------------------------ > u0 RAID-5 OK - - 64K 465.77 ON - > > Port Status Unit Size Blocks Serial > --------------------------------------------------------------- > p0 OK u0 232.88 GB 488397168 301012FP432889 > p1 NOT-PRESENT - - - - > p2 OK u0 232.88 GB 488397168 S09QJ1GL302662 > p3 OK u0 232.88 GB 488397168 S09QJ1GL302666
Ergo: Die erste Platte hat bei 200000 Zugriffen keine Daten liefern
können. Die dritte Platte scheint (selten) mal Probleme dabei zu
haben, die Spur zu finden.
MfG, JBG
--
Jan-Benedict Glaw [email protected] +49-172-7608481
Signature of: God put me on earth to accomplish a certain number of
the second : things. Right now I am so far behind I will never die.
signature.asc
Description: Digital signature
-- Linux mailing list [email protected] subscribe/unsubscribe: http://lug-owl.de/mailman/listinfo/linux Hinweise zur Nutzung: http://www.lug-owl.de/Mailingliste/hints.epo
