Am Dienstag, 13. Januar 2009 11:47:27 schrieb Jan-Benedict Glaw: > On Sat, 2009-01-10 12:28:24 +0100, Konstantin Nebel <[email protected]> wrote: > > Hi, > > > > ich habe ein 3ware 8506-4LP Raid Controller mit einem Raid-5 am Laufen. > > Ich höre ab und an fehlergeräusche von einer der Festplatten. Meiner > > Meinung nach sehe ich aber nichts in Smart, was auf einen Defekt > > hinweist. Hier die Auszüge den 3 Pladden. Vielleicht seht ihr den Fehler. > > > > smartctl version 5.38 [x86_64-pc-linux-gnu] Copyright (C) 2002-8 Bruce > > Allen Home page is http://smartmontools.sourceforge.net/ > > > > === START OF INFORMATION SECTION === > > Model Family: SAMSUNG SpinPoint P120 series > > Device Model: SAMSUNG SP2504C > > Serial Number: 301012FP432889 > > Firmware Version: VT100-59 > > User Capacity: 250.059.350.016 bytes > > Device is: In smartctl database [for details use: -P show] > > ATA Version is: 7 > > ATA Standard is: ATA/ATAPI-7 T13 1532D revision 4a > > Local Time is: Sat Jan 10 12:15:35 2009 CET > > > > ==> WARNING: May need -F samsung3 enabled; see manual for details. > > > > SMART support is: Available - device has SMART capability. > > SMART support is: Enabled > > > > === START OF READ SMART DATA SECTION === > > SMART overall-health self-assessment test result: PASSED > > > > General SMART Values: > > Offline data collection status: (0x02) Offline data collection activity > > was completed without error. > > Auto Offline Data Collection: Disabled. > > Self-test execution status: ( 0) The previous self-test routine > > completed > > without error or no self-test has ever > > been run. > > Total time to complete Offline > > data collection: (5066) seconds. > > Offline data collection > > capabilities: (0x5b) SMART execute Offline immediate. > > Auto Offline data collection on/off > > support. > > Suspend Offline collection upon new > > command. > > Offline surface scan supported. > > Self-test supported. > > No Conveyance Self-test supported. > > Selective Self-test supported. > > SMART capabilities: (0x0003) Saves SMART data before entering > > power-saving mode. > > Supports SMART auto save timer. > > Error logging capability: (0x01) Error logging supported. > > General Purpose Logging supported. > > Short self-test routine > > recommended polling time: ( 1) minutes. > > Extended self-test routine > > recommended polling time: ( 84) minutes. > > SCT capabilities: (0x003f) SCT Status supported. > > SCT Feature Control supported. > > SCT Data Table supported. > > > > SMART Attributes Data Structure revision number: 16 > > Vendor Specific SMART Attributes with Thresholds: > > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED > > WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 100 051 > > Pre-fail Always - 0 3 Spin_Up_Time 0x0007 > > 253 253 025 Pre-fail Always - 5824 4 Start_Stop_Count > > 0x0032 100 100 000 Old_age Always - 92 5 > > Reallocated_Sector_Ct 0x0033 253 253 010 Pre-fail Always > > - 0 7 Seek_Error_Rate 0x000f 253 253 051 Pre-fail > > Always - 0 8 Seek_Time_Performance 0x0025 253 253 > > 015 Pre-fail Offline - 0 9 Power_On_Hours 0x0032 > > 100 100 000 Old_age Always - 3032 10 > > Spin_Retry_Count 0x0033 253 253 051 Pre-fail Always > > - 0 11 Calibration_Retry_Count 0x0012 253 253 000 Old_age > > Always - 0 12 Power_Cycle_Count 0x0032 100 100 > > 000 Old_age Always - 83 187 Reported_Uncorrect > > 0x0032 253 253 000 Old_age Always - 196608 > > > ^^^^^^ > > > 190 Airflow_Temperature_Cel 0x0022 109 094 000 Old_age Always > > - 43 194 Temperature_Celsius 0x0022 109 094 000 > > Old_age Always - 43 195 Hardware_ECC_Recovered 0x001a > > 100 100 000 Old_age Always - 25285952 196 > > Reallocated_Event_Count 0x0032 253 253 000 Old_age Always > > - 0 197 Current_Pending_Sector 0x0012 253 253 000 > > Old_age Always - 0 198 Offline_Uncorrectable 0x0030 253 > > 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count > > 0x003e 200 200 000 Old_age Always - 0 200 > > Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always > > - 0 201 Soft_Read_Error_Rate 0x000a 100 100 000 > > Old_age Always - 0 202 TA_Increase_Count 0x0032 253 > > 253 000 Old_age Always - 0 > > > > SMART Error Log Version: 1 > > No Errors Logged > > > > SMART Self-test log structure revision number 1 > > Num Test_Description Status Remaining > > LifeTime(hours) LBA_of_first_error > > # 1 Extended offline Completed without error 00% 2793 > > - # 2 Extended offline Interrupted (host reset) 70% 2346 > > - # 3 Extended offline Completed without error 00% > > 1417 - # 4 Extended offline Completed without error 00% > > 643 - # 5 Extended offline Completed without error > > 00% 360 - # 6 Extended offline Completed without error > > 00% 245 - > > > > SMART Selective Self-Test Log Data Structure Revision Number (0) should > > be 1 SMART Selective self-test log data structure revision number 0 > > Warning: ATA Specification requires selective self-test log data > > structure revision number = 1 > > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS > > 1 0 0 Not_testing > > 2 0 0 Not_testing > > 3 0 0 Not_testing > > 4 0 0 Not_testing > > 5 0 0 Not_testing > > Selective self-test flags (0x0): > > After scanning selected spans, do NOT read-scan remainder of disk. > > If Selective self-test is pending on power-up, resume after 0 minute > > delay. > > > > ______________________________________ > > > > > > smartctl version 5.38 [x86_64-pc-linux-gnu] Copyright (C) 2002-8 Bruce > > Allen Home page is http://smartmontools.sourceforge.net/ > > > > === START OF INFORMATION SECTION === > > Model Family: SAMSUNG SpinPoint P120 series > > Device Model: SAMSUNG SP2504C > > Serial Number: S09QJ1GL302662 > > Firmware Version: VT100-33 > > User Capacity: 250.059.350.016 bytes > > Device is: In smartctl database [for details use: -P show] > > ATA Version is: 7 > > ATA Standard is: ATA/ATAPI-7 T13 1532D revision 4a > > Local Time is: Sat Jan 10 12:15:51 2009 CET > > > > ==> WARNING: May need -F samsung3 enabled; see manual for details. > > > > SMART support is: Available - device has SMART capability. > > SMART support is: Enabled > > > > === START OF READ SMART DATA SECTION === > > SMART overall-health self-assessment test result: PASSED > > > > General SMART Values: > > Offline data collection status: (0x82) Offline data collection activity > > was completed without error. > > Auto Offline Data Collection: Enabled. > > Self-test execution status: ( 0) The previous self-test routine > > completed > > without error or no self-test has ever > > been run. > > Total time to complete Offline > > data collection: (4806) seconds. > > Offline data collection > > capabilities: (0x5b) SMART execute Offline immediate. > > Auto Offline data collection on/off > > support. > > Suspend Offline collection upon new > > command. > > Offline surface scan supported. > > Self-test supported. > > No Conveyance Self-test supported. > > Selective Self-test supported. > > SMART capabilities: (0x0003) Saves SMART data before entering > > power-saving mode. > > Supports SMART auto save timer. > > Error logging capability: (0x01) Error logging supported. > > General Purpose Logging supported. > > Short self-test routine > > recommended polling time: ( 1) minutes. > > Extended self-test routine > > recommended polling time: ( 80) minutes. > > > > SMART Attributes Data Structure revision number: 16 > > Vendor Specific SMART Attributes with Thresholds: > > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED > > WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 100 051 > > Pre-fail Always - 10 3 Spin_Up_Time 0x0007 > > 100 100 025 Pre-fail Always - 6016 4 Start_Stop_Count > > 0x0032 100 100 000 Old_age Always - 689 5 > > Reallocated_Sector_Ct 0x0033 077 077 010 Pre-fail Always > > - 219 7 Seek_Error_Rate 0x000f 253 253 051 > > Pre-fail Always - 0 8 Seek_Time_Performance 0x0025 253 > > 253 015 Pre-fail Offline - 0 9 Power_On_Hours > > 0x0032 100 100 000 Old_age Always - 17874 10 > > Spin_Retry_Count 0x0033 253 253 051 Pre-fail Always > > - 0 11 Calibration_Retry_Count 0x0012 253 002 000 Old_age > > Always - 0 12 Power_Cycle_Count 0x0032 100 100 > > 000 Old_age Always - 663 190 Airflow_Temperature_Cel > > 0x0022 115 082 000 Old_age Always - 41 194 > > Temperature_Celsius 0x0022 115 082 000 Old_age Always > > - 41 195 Hardware_ECC_Recovered 0x001a 100 100 000 > > Old_age Always - 17806828 196 Reallocated_Event_Count > > 0x0032 077 077 000 Old_age Always - 219 197 > > Current_Pending_Sector 0x0012 253 253 000 Old_age Always > > - 0 198 Offline_Uncorrectable 0x0030 253 253 000 > > Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 > > 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate > > 0x000a 100 100 000 Old_age Always - 0 201 > > Soft_Read_Error_Rate 0x000a 100 100 000 Old_age Always > > - 0 202 TA_Increase_Count 0x0032 253 253 000 > > Old_age Always - 0 > > > > SMART Error Log Version: 1 > > No Errors Logged > > > > SMART Self-test log structure revision number 1 > > Num Test_Description Status Remaining > > LifeTime(hours) LBA_of_first_error > > # 1 Extended offline Completed without error 00% 17638 > > - # 2 Extended offline Interrupted (host reset) 20% 17352 > > - # 3 Extended offline Completed without error 00% > > 16277 - # 4 Extended offline Completed without error > > 00% 15985 - # 5 Extended offline Completed without error > > 00% 15502 - # 6 Extended offline Completed without > > error 00% 15223 - # 7 Extended offline Completed > > without error 00% 15108 - # 8 Extended offline > > Completed without error 00% 14615 - # 9 Extended > > offline Completed without error 00% 14469 - #10 > > Extended offline Completed without error 00% 14202 - > > #11 Extended offline Completed without error 00% 14171 > > - > > > > SMART Selective Self-Test Log Data Structure Revision Number (0) should > > be 1 SMART Selective self-test log data structure revision number 0 > > Warning: ATA Specification requires selective self-test log data > > structure revision number = 1 > > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS > > 1 0 0 Not_testing > > 2 0 0 Not_testing > > 3 0 0 Not_testing > > 4 0 0 Not_testing > > 5 0 0 Not_testing > > Selective self-test flags (0x0): > > After scanning selected spans, do NOT read-scan remainder of disk. > > If Selective self-test is pending on power-up, resume after 0 minute > > delay. > > > > ______________________________________ > > > > smartctl version 5.38 [x86_64-pc-linux-gnu] Copyright (C) 2002-8 Bruce > > Allen Home page is http://smartmontools.sourceforge.net/ > > > > === START OF INFORMATION SECTION === > > Model Family: SAMSUNG SpinPoint P120 series > > Device Model: SAMSUNG SP2504C > > Serial Number: S09QJ1GL302666 > > Firmware Version: VT100-33 > > User Capacity: 250.059.350.016 bytes > > Device is: In smartctl database [for details use: -P show] > > ATA Version is: 7 > > ATA Standard is: ATA/ATAPI-7 T13 1532D revision 4a > > Local Time is: Sat Jan 10 12:15:57 2009 CET > > > > ==> WARNING: May need -F samsung3 enabled; see manual for details. > > > > SMART support is: Available - device has SMART capability. > > SMART support is: Enabled > > > > === START OF READ SMART DATA SECTION === > > SMART overall-health self-assessment test result: PASSED > > > > General SMART Values: > > Offline data collection status: (0x82) Offline data collection activity > > was completed without error. > > Auto Offline Data Collection: Enabled. > > Self-test execution status: ( 0) The previous self-test routine > > completed > > without error or no self-test has ever > > been run. > > Total time to complete Offline > > data collection: (4836) seconds. > > Offline data collection > > capabilities: (0x5b) SMART execute Offline immediate. > > Auto Offline data collection on/off > > support. > > Suspend Offline collection upon new > > command. > > Offline surface scan supported. > > Self-test supported. > > No Conveyance Self-test supported. > > Selective Self-test supported. > > SMART capabilities: (0x0003) Saves SMART data before entering > > power-saving mode. > > Supports SMART auto save timer. > > Error logging capability: (0x01) Error logging supported. > > General Purpose Logging supported. > > Short self-test routine > > recommended polling time: ( 1) minutes. > > Extended self-test routine > > recommended polling time: ( 80) minutes. > > > > SMART Attributes Data Structure revision number: 16 > > Vendor Specific SMART Attributes with Thresholds: > > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED > > WHEN_FAILED RAW_VALUE > > 1 Raw_Read_Error_Rate 0x000f 100 099 051 Pre-fail Always > > - 163 3 Spin_Up_Time 0x0007 100 100 025 > > Pre-fail Always - 5952 4 Start_Stop_Count 0x0032 > > 100 100 000 Old_age Always - 692 5 > > Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always > > - 1 7 Seek_Error_Rate 0x000f 253 253 051 Pre-fail > > Always - 0 8 Seek_Time_Performance 0x0025 253 253 > > 015 Pre-fail Offline - 0 9 Power_On_Hours 0x0032 > > 100 100 000 Old_age Always - 17893 10 > > Spin_Retry_Count 0x0033 253 253 051 Pre-fail Always > > - 0 11 Calibration_Retry_Count 0x0012 100 002 000 Old_age > > Always - 33 > > > ^^ > > > 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always > > - 666 190 Airflow_Temperature_Cel 0x0022 121 082 000 > > Old_age Always - 39 194 Temperature_Celsius 0x0022 > > 121 082 000 Old_age Always - 39 195 > > Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always > > - 44236889 196 Reallocated_Event_Count 0x0032 100 100 000 > > Old_age Always - 1 197 Current_Pending_Sector 0x0012 253 > > 100 000 Old_age Always - 0 198 Offline_Uncorrectable > > 0x0030 253 253 000 Old_age Offline - 0 199 > > UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always > > - 0 200 Multi_Zone_Error_Rate 0x000a 100 100 000 > > Old_age Always - 0 201 Soft_Read_Error_Rate 0x000a 100 > > 100 000 Old_age Always - 0 202 TA_Increase_Count > > 0x0032 253 253 000 Old_age Always - 0 > > > > SMART Error Log Version: 1 > > No Errors Logged > > > > SMART Self-test log structure revision number 1 > > Num Test_Description Status Remaining > > LifeTime(hours) LBA_of_first_error > > # 1 Extended offline Completed without error 00% 17657 > > - # 2 Extended offline Interrupted (host reset) 40% 17361 > > - # 3 Extended offline Completed without error 00% > > 16457 - # 4 Extended offline Completed without error > > 00% 16288 - # 5 Extended offline Completed without error > > 00% 15997 - # 6 Extended offline Completed without > > error 00% 15514 - # 7 Extended offline Completed > > without error 00% 15235 - # 8 Extended offline > > Completed without error 00% 15120 - # 9 Extended > > offline Completed without error 00% 14627 - #10 > > Extended offline Completed without error 00% 14481 - > > #11 Extended offline Completed without error 00% 14210 > > - #12 Extended offline Completed without error 00% 14182 > > - > > > > SMART Selective Self-Test Log Data Structure Revision Number (0) should > > be 1 SMART Selective self-test log data structure revision number 0 > > Warning: ATA Specification requires selective self-test log data > > structure revision number = 1 > > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS > > 1 0 0 Not_testing > > 2 0 0 Not_testing > > 3 0 0 Not_testing > > 4 0 0 Not_testing > > 5 0 0 Not_testing > > Selective self-test flags (0x0): > > After scanning selected spans, do NOT read-scan remainder of disk. > > If Selective self-test is pending on power-up, resume after 0 minute > > delay. > > > > Hier noch der Auszug aus dem Raid-Controller: > > > > Unit UnitType Status %RCmpl %V/I/M Stripe Size(GB) Cache > > AVrfy > > ------------------------------------------------------------------------- > >----- u0 RAID-5 OK - - 64K 465.77 ON > > - > > > > Port Status Unit Size Blocks Serial > > --------------------------------------------------------------- > > p0 OK u0 232.88 GB 488397168 301012FP432889 > > p1 NOT-PRESENT - - - - > > p2 OK u0 232.88 GB 488397168 S09QJ1GL302662 > > p3 OK u0 232.88 GB 488397168 S09QJ1GL302666 > > Ergo: Die erste Platte hat bei 200000 Zugriffen keine Daten liefern > können. Die dritte Platte scheint (selten) mal Probleme dabei zu > haben, die Spur zu finden. > > MfG, JBG
Hi Jan, soll ich die Platte tauschen? Und sei mir nich böse. An welcher Ausgabe hast du das genau erkannt? -- Mit freundlichen Grüßen, Konstantin Nebel 05472 / 9544415 0175 / 3584447 [email protected] -- Linux mailing list [email protected] subscribe/unsubscribe: http://lug-owl.de/mailman/listinfo/linux Hinweise zur Nutzung: http://www.lug-owl.de/Mailingliste/hints.epo
