Thanks for your reply,  I wil do some test with iperf I will try also 3750G-

2012/3/18 Adam Thompson <[email protected]>

> The 3750X series is as yet unknown – I don’t have direct experience yet,
> nor does anyone I know – but the older switches I’ve used in the 3750
> family are not very good routers, in fact roughly on par with the
> 1800-series routers from Cisco.  That is, they’re not bad, but not as good
> as anything with hardware acceleration.  I don’t think you will get
> hardware-accelerated routing in any L3-capable switch, I think you have to
> go up to a Nexus series switch with Cisco to get that.  In Juniper product,
> you need (roughly) an MX-series or  T-series to get h/w-accelerated
> routing.  Both vendors can sell you a router with an embedded switch, which
> is a completely different product.****
>
> IMHO, for lowest jitter, use a dedicated L2 switch and a dedicated L3
> router, and use both 802.1p and IP TOS CoS markings (and use them in the
> router). ****
>
> ** **
>
> With pfSense, you **might** experience better performance by using
> individual interfaces instead of a tagged trunk; I know from experience
> that QoS suffers noticeably as soon as you introduce LACP LAGs into the
> network.  When comparing vyatta, keep in mind that some drivers under linux
> not only support polling but also support direct card-to-card DMA (known as
> “zero-copy routing”, I think), thus avoiding a relatively-expensive copy
> into and back out of main memory.****
>
> ** **
>
> -Adam Thompson****
>
> [email protected]****
>
> ** **
>
> ** **
>
> *From:* [email protected] [mailto:
> [email protected]] *On Behalf Of *Igor Battiston
> *Sent:* Saturday, March 17, 2012 7:41 PM
> *To:* [email protected]
> *Subject:* [pfSense] Some questions about pps performance...****
>
> ** **
>
> Hi, ****
>
>   in using pfsense 1.2 like edge router/firewall in a small voip operator,
> it's working well from several years, I can give you some 'real life'
> benchmark.****
>
> ** **
>
> Server is:****
>
> HP DL with a 3075 XEON****
>
> hw.model: Intel(R) Xeon(R) CPU            3075  @ 2.66GHz****
>
> ** **
>
> Ethernet card is****
>
> HP NCT-360T****
>
> dev.em.0.%desc: Intel(R) PRO/1000 Network Connection Version - 6.2.9****
>
> dev.em.1.%desc: Intel(R) PRO/1000 Network Connection Version - 6.2.9****
>
> ** **
>
> I have some vlan with inter-vlan routing/firewalling, total WAN traffic is
> around 40mbit (all RTP) small packets... I have 100mbit on the VLAN trunk
> interface...****
>
> ** **
>
> In this scenario and with this hardware pfsense works well, but if I try
> to increase traffic I start to see a jitter , the CPU IRQ  load start to
> become greater than 60%... I studied a little bit about polling, with linux
> the e1000 drivers have a system to mitigate interrupt load ( i didn't yet
> tested if linux has better performance than freebsd) I googled and i found
> some test about pfsense and linux (vyatta) but the test was done with
> realtek cards, and it's depends too much to the quality of the drivers....
> ****
>
> ** **
>
> ** **
>
> In my opinion the 'polling' is not too bad... with a 1000hz kernel means
> 1ms of additional delay and delay it's better than jitter in rtp.****
>
> ** **
>
> Do you think i can continue to use pfsense or will it be better to use an
> L3 switch like cisco 3750G ? ****
>
> ** **
>
> ** **
>
> _______________________________________________
> List mailing list
> [email protected]
> http://lists.pfsense.org/mailman/listinfo/list
>
>
_______________________________________________
List mailing list
[email protected]
http://lists.pfsense.org/mailman/listinfo/list

Reply via email to