Hello, please reply with your lts.conf /// Appiah
On Mon, Jan 11, 2010 at 8:47 AM, james <j...@tigger.ws> wrote: > G'day > > With the latest karmic - ltsp setup Of the first 3 thin clients I tried 1 > works. > > #2 asus m2n68-am and samsung monitor - Display out of range. > > The probe discovers correct stuff > .. > (II) NV(0): Probing for EDID on I2C bus A... > (II) NV(0): I2C device "DDC:E-EDID segment register" registered at address > 0x60. > (II) NV(0): I2C device "DDC:ddc2" registered at address 0xA0. > (II) NV(0): ... none found > (II) NV(0): Probing for EDID on I2C bus B... > (--) NV(0): DDC detected a CRT: > (II) NV(0): Manufacturer: SAM Model: 1e1 Serial#: 1212231993 > (II) NV(0): Year: 2006 Week: 27 > (II) NV(0): EDID Version: 1.3 > (II) NV(0): Analog Display Input, Input Voltage Level: 0.700/0.300 V > (II) NV(0): Sync: Separate Composite SyncOnGreen > (II) NV(0): Max Image Size [cm]: horiz.: 38 vert.: 30 > (II) NV(0): Gamma: 2.20 > (II) NV(0): DPMS capabilities: Off; RGB/Color Display > (II) NV(0): First detailed timing is preferred mode > (II) NV(0): redX: 0.640 redY: 0.329 greenX: 0.300 greenY: 0.600 > (II) NV(0): blueX: 0.150 blueY: 0.060 whiteX: 0.313 whiteY: 0.329 > (II) NV(0): Supported established timings: > (II) NV(0): 720x...@75hz > [snip] > (II) NV(0): 1024x...@75hz > (II) NV(0): 1280x1...@75hz > (II) NV(0): 1152x...@75hz > (II) NV(0): Manufacturer's mask: 0 > (II) NV(0): Supported standard timings: > (II) NV(0): #0: hsize: 1280 vsize 1024 refresh: 60 vid: 32897 > (II) NV(0): #1: hsize: 1280 vsize 960 refresh: 60 vid: 16513 > (II) NV(0): #2: hsize: 1152 vsize 864 refresh: 75 vid: 20337 > (II) NV(0): Supported detailed timing: > (II) NV(0): clock: 108.0 MHz Image Size: 376 x 301 mm > (II) NV(0): h_active: 1280 h_sync: 1328 h_sync_end 1440 h_blank_end 1688 > h_border: 0 > (II) NV(0): v_active: 1024 v_sync: 1025 v_sync_end 1028 v_blanking: 1066 > v_border: 0 > (II) NV(0): Ranges: V min: 56 V max: 75 Hz, H min: 30 H max: 81 kHz, PixClock > max 140 MHz > (II) NV(0): Monitor name: SyncMaster > (II) NV(0): Serial No: HMCL700620 > (II) NV(0): EDID (in hex): > ... > So it finds 1280x1...@60hz then does not use it. > All X_MODE and X_VERTREFRESH lines are utterly ignored. > > #3 > Try a gigabyte GA-MA78GM-S2H, same monitor. It runs 800x600 and again ignores > X_MODE and X_VERTREFRESH in lts.conf. > > What is happening? Is this going back to hand crafted xorg.conf files? > > BTW installing karmic on this hardware works correctly > James > > ------------------------------------------------------------------------------ > This SF.Net email is sponsored by the Verizon Developer Community > Take advantage of Verizon's best-in-class app development support > A streamlined, 14 day to market process makes app distribution fast and easy > Join now and get one step closer to millions of Verizon customers > http://p.sf.net/sfu/verizon-dev2dev > _____________________________________________________________________ > Ltsp-discuss mailing list. To un-subscribe, or change prefs, goto: > https://lists.sourceforge.net/lists/listinfo/ltsp-discuss > For additional LTSP help, try #ltsp channel on irc.freenode.net > ------------------------------------------------------------------------------ This SF.Net email is sponsored by the Verizon Developer Community Take advantage of Verizon's best-in-class app development support A streamlined, 14 day to market process makes app distribution fast and easy Join now and get one step closer to millions of Verizon customers http://p.sf.net/sfu/verizon-dev2dev _____________________________________________________________________ Ltsp-discuss mailing list. To un-subscribe, or change prefs, goto: https://lists.sourceforge.net/lists/listinfo/ltsp-discuss For additional LTSP help, try #ltsp channel on irc.freenode.net
