Ok, forcing sensor=1 I can load module m5602-ov9650-2. /home/willy/software/pequeno/webcam/svn/m560x-driver/m560x/branches/m5602-ov9650-2/m5602_v4l2.c: m5602 open /home/willy/software/pequeno/webcam/svn/m560x-driver/m560x/branches/m5602-ov9650-2/m5602_v4l2.c: m5602 open /home/willy/software/pequeno/webcam/svn/m560x-driver/m560x/branches/m5602-ov9650-2/m5602_v4l2.c: m5602 open /home/willy/software/pequeno/webcam/svn/m560x-driver/m560x/branches/m5602-ov9650-2/m5602.c: usb_m5602_exit - WebCam driver shutdown usbcore: deregistering interface driver m5602 /home/willy/software/pequeno/webcam/svn/m560x-driver/m560x/branches/m5602-ov9650-2/m5602.c: m5602 release resources video device 0 /home/willy/software/pequeno/webcam/svn/m560x-driver/m560x/branches/m5602-ov9650-2/m5602.c: m5602_disconnect- M560x-based WebCam disconnected Linux video capture interface: v2.00 /home/willy/software/pequeno/webcam/svn/m560x-driver/m560x/branches/m5602-ov9650-2/m5602.c: usb_m5602_init - WebCam driver startup /home/willy/software/pequeno/webcam/svn/m560x-driver/m560x/branches/m5602-ov9650-2/m5602.c: BisonCam webcam found. /home/willy/software/pequeno/webcam/svn/m560x-driver/m560x/branches/m5602-ov9650-2/m5602.c: Probing for an ov9650 sensor /home/willy/software/pequeno/webcam/svn/m560x-driver/m560x/branches/m5602-ov9650-2/m5602.c: I2C_BUSY, 0xc7 /home/willy/software/pequeno/webcam/svn/m560x-driver/m560x/branches/m5602-ov9650-2/m5602.c: Sensor reported as 0xff:0xff /home/willy/software/pequeno/webcam/svn/m560x-driver/m560x/branches/m5602-ov9650-2/m5602.c: Forcing an ov9650 sensor /home/willy/software/pequeno/webcam/svn/m560x-driver/m560x/branches/m5602-ov9650-2/m5602.c: If this works, please report your sensor product id: 0xff:0xff to [email protected] /home/willy/software/pequeno/webcam/svn/m560x-driver/m560x/branches/m5602-ov9650-2/m5602.c: m5602_probe - m5602 WebCam driver is now controlling video device 0 usbcore: registered new interface driver m5602 /home/willy/software/pequeno/webcam/svn/m560x-driver/m560x/branches/m5602-ov9650-2/m5602.c: 0.1.0:M5602 Webcam Driver
But when I start livecam (640x480 rgb24) I can't get any image (Bison Cam @ 0 fps). No errors in dmesg nor in syslog... Any ideas? Il giorno mer, 12/03/2008 alle 10.55 +0100, Erik Andrén ha scritto: > Hi Willy, > > 2008/3/12, willy <[EMAIL PROTECTED]>: > Hi! > I have already tried to load m5602-ov9650-2 modules > but it doesn't > detect the sensor. It says "no supported sensor found". > > Have you tried to insert the module with the force=1 parameter? > > If it works, please report your sensor id to this list. > Also, make sure you test the cam with the livecam application, nothing > else works for the moment AFAICT. > > Regards, > Erik > ------------------------------------------------------------------------- This SF.net email is sponsored by: Microsoft Defy all challenges. Microsoft(R) Visual Studio 2008. http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/ _______________________________________________ M560x-driver-devel mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/m560x-driver-devel
