addon: i have flashed an old image on the sd card and on startup it said the exact same but after 5-6 seconds in booted up like normal
Am Samstag, 1. Oktober 2016 19:32:56 UTC+2 schrieb Sag ich Dir nich: > > thanks i was able to recover the config via Live "CD", > > i had 4 times, where something on the card (probably) was corrupted (3 > times i could not log in, i had to skip touchscreen calibration twice and > it would always reboot, the 4th time it wasnt even booting up), maybe the > card is defective, should i get another sd card? > > Am Freitag, 30. September 2016 21:00:48 UTC+2 schrieb Charles Steinkuehler: >> >> Yes, pretty much any Linux system you can hook a uSD card reader to >> should work. >> >> Besides the image from LinuxCNC, there are many "rescue" releases >> available. I always keep SystemRescueCD setup to network boot, so if >> I ever have a problem with any machine I can just reboot, go to the >> boot menu, and run Linux out of ram straight from the network. :) >> >> On 9/30/2016 1:42 PM, Sag ich Dir nich wrote: >> > I dont have a Linux system but can i try booting Linuxcnc testversion >> using a >> > USB stick? Will that work? >> > >> > Am Freitag, 30. September 2016 13:41:29 UTC+2 schrieb Charles >> Steinkuehler: >> > >> > If you have another Linux system available, you can run fsck on the >> > uSD filesystem and possibly copy off your data if the uSD is having >> > problems. Since the system doesn't boot with the old screen, I >> > suspect you have some sort of corruption. Note that you have to >> > cleanly shut-down the BeagleBone (don't just power it off) or you >> will >> > get file system corruption. I've also had uSD cards that just >> became >> > flaky...typically they work OK again after reformatting. >> > >> > On 9/30/2016 4:53 AM, Sag ich Dir nich wrote: >> > > unfortunately i dont know if it was before, but would that mean >> i have to >> > flash >> > > the microsd card again? can i somehow extract the configuration? >> > > >> > > Am Freitag, 30. September 2016 01:58:01 UTC+2 schrieb Charles >> Steinkuehler: >> > > >> > > On 9/28/2016 4:05 PM, Sag ich Dir nich wrote: >> > > > Hi, >> > > > >> > > > today i received my new bigger screen (old screen >> 800x480, new >> > 1280x800) and >> > > > plugged it into the Beaglebone, first boot was almost >> normal, >> > except for it >> > > > loaded like 100 digits (which i could not recognize, >> because it >> > was so >> > > fast) i >> > > > was able to load the machine and everything was normal... >> then i >> > rebooted >> > > and i >> > > > get this every time i boot: >> > > >> > > > [ 0.706640] omap_hsmmc mmc.5: >> of_parse_phandle_with_args of >> > ´reset´ >> > > failed >> > > >> > > <snip> >> > > >> > > > it does also not boot with the old screen >> > > >> > > Was the mmc error there previously? Your eMMC or uSD card >> could be >> > > corrupt or failed. >> > > >> > > -- >> > > Charles Steinkuehler >> > > [email protected] <javascript:> >> > > >> > > -- >> > > website: http://www.machinekit.io blog: >> http://blog.machinekit.io github: >> > > https://github.com/machinekit >> > > --- >> > > You received this message because you are subscribed to the >> Google Groups >> > > "Machinekit" group. >> > > To unsubscribe from this group and stop receiving emails from >> it, send an >> > email >> > > to [email protected] <javascript:> >> > > <mailto:[email protected] <javascript:>>. >> > > Visit this group at https://groups.google.com/group/machinekit >> > <https://groups.google.com/group/machinekit>. >> > > For more options, visit https://groups.google.com/d/optout >> > <https://groups.google.com/d/optout>. >> > > >> > >> > >> > -- >> > Charles Steinkuehler >> > [email protected] <javascript:> >> > >> > -- >> > website: http://www.machinekit.io blog: http://blog.machinekit.io >> github: >> > https://github.com/machinekit >> > --- >> > You received this message because you are subscribed to the Google >> Groups >> > "Machinekit" group. >> > To unsubscribe from this group and stop receiving emails from it, send >> an email >> > to [email protected] >> > <mailto:[email protected]>. >> > Visit this group at https://groups.google.com/group/machinekit. >> > For more options, visit https://groups.google.com/d/optout. >> > >> >> >> -- >> Charles Steinkuehler >> [email protected] >> > -- website: http://www.machinekit.io blog: http://blog.machinekit.io github: https://github.com/machinekit --- You received this message because you are subscribed to the Google Groups "Machinekit" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. Visit this group at https://groups.google.com/group/machinekit. For more options, visit https://groups.google.com/d/optout.
