I think you can perform the following procedures to get the results you
need:
1 To set the breakpoint in the 241 line of runpf.m file
2 To compute the load flow of specified , for example. runpf ('case118')
3. To check the bus, gen, branch in workspace to get the results
Good luck!
On Tue, Nov 25, 2008 at 10:17 AM, Dr. Ismail Musirin
<[email protected]>wrote:
> Dear Di Wu,
>
> Thanks for the email. I understand that we need to set the break point.
> Would you please kindly let me know the exact break point. I hope this
> does not interrupt your time.
>
> I understand that once the load flow has been converged, the workspace is
> deleted in order to reduce the memory of our computer. I appreciate your
> advice.
>
> **Best regards.
>
>
> ------------------------------
> *From:* di wu <[email protected]>
> *To:* MATPOWER discussion forum <[email protected]>
> *Sent:* Tuesday, 25 November, 2008 17:06:17
> *Subject:* Re: MATPOWER QUESTIONS
>
> First of all, you should set the breakpoint at the end of runpf.m. Then,
> you solve the power flow so that you can get the results you need.
>
> On Tue, Nov 25, 2008 at 10:00 AM, Dr. Ismail Musirin <
> [email protected]> wrote:
>
>> Thank you Di Wu,
>>
>> I know that. But my workspace is empty. No variables at all. Pls help.
>>
>> Thank you.
>>
>> Regards.
>>
>> Ismail
>>
>> ------------------------------
>> *From:* di wu <[email protected]>
>> *To:* MATPOWER discussion forum <[email protected]>
>> *Sent:* Tuesday, 25 November, 2008 16:57:29
>> *Subject:* Re: MATPOWER QUESTIONS
>>
>> Actually, the load flow results you need have saved in the varaibles of
>> workspace (i.e. the variables is bus, gen, branch). That is, the vairables
>> (bus, gen, branch in workspace) have been updated when the results have been
>> on screen.
>>
>> On Tue, Nov 25, 2008 at 8:53 AM, Dr. Ismail Musirin <
>> [email protected]> wrote:
>>
>>> Dear all,
>>>
>>>
>>> I am Ismail Musirin from Universiti Teknologi MARA, Malaysia. First of
>>> all, I must say thank you to Prof. Ray Zimmerman for the power flow package
>>> you developed to solve the power flow problems.
>>>
>>> I am writing to you to ask how can I extract all the load flow results
>>> and put them in the workspace. Apparently using the following example:-
>>>
>>> >> runpf 'case118'
>>>
>>> we may get beautiful load flow results on the screen or command window.
>>> However, the variables such as the bus and branch variables are not appeared
>>> in the workspace. I need to know all these variables in order to do my
>>> further coding.
>>>
>>> I appreciate your response.
>>>
>>> Best regards.
>>>
>>> *Associate Professor Dr. Ismail Musirin
>>> * *(MIEEE, -PES, -CIS, -CMCS, ARTIST, IAENG) *
>>> *Faculty of Electrical Engineering
>>> Universiti Teknologi MARA
>>> 40450 Shah Alam, Selangor
>>> MALAYSIA
>>>
>>> Tel: 603-55435044 or 6012-6603864
>>> Fax: 603-55435044*
>>>
>>>
>>>
>>>
>>
>>
>> --
>> Di Wu
>> POLITECNICO DI TORINO
>> Dipartimento di Ingegneria Elettrica
>> Corso Duca degli Abruzzi, 24,
>> 10129 TORINO - ITALY
>> Tel . +39 011 090 7117
>> Fax. +39 011 090 7199
>> Email [email protected]
>>
>>
>
>
> --
> Di Wu
> POLITECNICO DI TORINO
> Dipartimento di Ingegneria Elettrica
> Corso Duca degli Abruzzi, 24,
> 10129 TORINO - ITALY
> Tel . +39 011 090 7117
> Fax. +39 011 090 7199
> Email [email protected]
>
>
--
Di Wu
POLITECNICO DI TORINO
Dipartimento di Ingegneria Elettrica
Corso Duca degli Abruzzi, 24,
10129 TORINO - ITALY
Tel . +39 011 090 7117
Fax. +39 011 090 7199
Email [email protected]
