Ive seen a similar setup using a chopper disk arrangment inside a large dist without the cap etc.He was also running a boost retard type arrangment to give it that almost 3 dimensional maping when combined with the jaycar controller.He had previously run it without the boost retard but the holden6 ran pretty hot on highway cruising with not much advance.
"GREENBURY, Andrew Robert" wrote: > Gday Pete, > > Did you consider the use of a chopper disk mounted to the pulley? You > could have still used hall effect, or optical sensor instead, mounted in > the same position you used. But the chopper disk could still be rotated in > place for final adjustments, allowing easier fine tuning of base timing, > therefore the installation is less critical than the positioning of > magnets in the pulley etc. If only 2 pulses per rev are required, then a > "chopper disk" could consist of a simple rectangular steel strip a bit > longer than the pulley diameter. Plus if your future mods require more > pulses per rev, simply make a new chopper disk rather than having to add > more magnets to the pulley? > > Andrew > > On Sun, 24 Nov 2002, Pete Parnell wrote: > > > Mal, > > Bolt on. I glued the hall sensor on an alluminium bracket I made > > and bolted the bracket through 2 timing cover bolts. When the sensor is > > mounted you can then work out the position of the magnets. > > > > ie, mount the sensor first ( allowing for adjustment as this sets the > > base timing) then mark the pulley, remove the pulley. drill holes and > > glue in magnets. > > > > Pete. > > ----- Original Message ----- > > From: maldat > > To: [EMAIL PROTECTED] > > Sent: Saturday, November 23, 2002 10:50 PM > > Subject: Re: new web site > > > > > > Thats what I want so smooth reving over 8000Rpm. > > > > To attach the pickup ??is it a bolt on or a weld on??? > > I have seen one set up like yours using motorbike bits and the pickup plate was >welded on the timmimg cover. > > > > Welded on means ,If I want your set up I'd have to post you my timming cover,cos >its all been decked. > > Malcolm > > ----- Original Message ----- > > From: Pete Parnell > > To: Ozdat List > > Sent: Sunday, November 24, 2002 1:30 AM > > Subject: new web site > > > > > > http://www.members.optusnet.com.au/~peterandtrace/ > > > > People this is my web site displaying my crank triggered, programmable, coil >pack ignition system designed for those that want to get rid of their dizzys. > > > > Still more info and photos to come. But you gotta start somewhere!! > > > > Pete. > > > > --membersozdat------------------------------------------------------- > > OZDAT Mailing List Please Note:- > > Send (un)subscribe requests to [EMAIL PROTECTED] > > Send submissions to [EMAIL PROTECTED] > > No unauthorised redistribution of this email > > http://www.ozdat.com/ozdatonline/index.htm > > http://www.ozdat.com/ozdatonline/listindex.html > > http://www.mail-archive.com/[email protected]/ > > --------------------------------------------------------------------- > > > > --membersozdat------------------------------------------------------- > > OZDAT Mailing List Please Note:- > > Send (un)subscribe requests to [EMAIL PROTECTED] > > Send submissions to [EMAIL PROTECTED] > > No unauthorised redistribution of this email > > http://www.ozdat.com/ozdatonline/index.htm > > http://www.ozdat.com/ozdatonline/listindex.html > > http://www.mail-archive.com/[email protected]/ > > --------------------------------------------------------------------- > > > --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/[email protected]/ ---------------------------------------------------------------------
