Also, make sure what your welding is clean!
Rod Fowler
Email: [EMAIL PROTECTED]
URL: Nissan Appreciation Page
http://www.geocities.com/toasterino
From: "Rob P" <[EMAIL PROTECTED]>
Reply-To: [EMAIL PROTECTED]
To: <[EMAIL PROTECTED]>
Subject: Re: Welder advice
Date: Wed, 11 Dec 2002 09:48:22 +0800
Julian,
I'm using a mini-roll of 0.6 wire, this was recommended to me for car
panelwork, worked well on my baffled sump welding and bodywork but I need
more practice, it's pretty easy to burn a hole right through. I am an expert
Arc (rod) welder, but I can't seem to make my MIG welds as neatly as Arc
welds. I have a big roll of 0.9 wire with which it is just possible to
repair panels with but not easy. 0.9 is probably better for thicker-walled
exhaust tubing and flanges. Go the 0.6 for panels, I'm using Argoshield (a
mixture of Argon and CO2) gas on a Butters MIG single phase (home power
point) welder. Practice on scrap before you start welding your priceless
1600 panels!
If you want to weld Stainless Steel, it requires a TIG welder. My mate did
weld up a stainless fuel tank using plain steel wire and a MIG welder but
the welds will rust if left untreated (on the outside of the tank anyway).
It's not the normal way to do it.
You can just swap the gas on some MIG welders and get a different handpeice.
TIG welding requires different electrical pulsing and not all MIG welders
have the ability to change the pulsing. TIG welding is also not wire-fed
welding, you have a Tungsten handpiece and you use a rod to weld with. The
gas used in TIG (for stainless, aluminium and alloy) is pure Argon, not
Argoshield.
Hope this helps.
Regards,
Rob P
----- Original Message -----
From: "mark krawczuk" <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Sent: Tuesday, December 10, 2002 10:10 PM
Subject: Re: Welder advice
> hi, get a gas welder, NOT a gassless.
> the gassless gets HEAPS more spatter, and the finish is no where as good
as
> the gas.
> i would be using just about the thinnest mig wire possible for what yor
> using, my brother had .8 or something mig wire, then went down to
thinner
> mig wire , and he said it made a heap of difference.
> he mainly welds car panels and other thin metals.
>
>
> mark k
> ----- Original Message -----
> From: "Julian" <[EMAIL PROTECTED]>
> To: <[EMAIL PROTECTED]>
> Sent: Tuesday, December 10, 2002 10:17 PM
> Subject: Welder advice
>
>
> > I remember reading ages ago a thread about which welder to buy, and what
> > you need to look for etc but I had a look for the archives but there
> > doesn't seem to be any???
> >
> > Anyway, I figure im gonna spend between $500 and $1000 on a welder , i
> > guess MIG, mainly to do exhausts, body work, fix the garage etc. Maybe
> > a turbo manifold if I am any good at welding.
> >
> > Basically I am wondering what power to get, where to get it, what to
> > look for, gas or gas less? Im in Melbourne so can you suggest anywhere
> > to buy it from?
> >
> > I have a friend who is a stainless worker who is going to teach me how
> > to weld (he doesn't know it yet!) so hopefully I can work it out.
> >
> > thanks
> > - Julian
> >
> >
>
>
_________________________________________________________________
Add photos to your e-mail with MSN 8. Get 2 months FREE*. http://join.msn.com/?page=features/featuredemail
--membersozdat-------------------------------------------------------
OZDAT Mailing List Please Note:-
Send (un)subscribe requests to [EMAIL PROTECTED]
Send submissions to [EMAIL PROTECTED]
No unauthorised redistribution of this email
http://www.ozdat.com/ozdatonline/index.htm
http://www.ozdat.com/ozdatonline/listindex.html
http://www.mail-archive.com/[email protected]/
---------------------------------------------------------------------
