They sure do but '71 struts are usually 11.5" jobs (as in very long). Late 180B struts are preferred as they are 10.25" and have 74mm stub axles. With Verada discs you need a bit of re-drilling and machining know how etc and 15" wheels, small weld job to reduce the centre hole in the disc by 1mm for 1600 struts, machine out to 74mm for 180B, re-drill the discs to suit the Datto hub bolt circle and not much else other than a fair bit of spare cash to enable you to use all new parts. Magna discs can also be used and they will fit 14" wheels. You may still be able to buy the Magna based kit from SSS, not sure of what $$$ these days though.
regards Terry -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Duncan Shillito Sent: Monday, 24 March 2003 2:23 PM To: [EMAIL PROTECTED] Subject: RE: brake conversion. so, do verada disks and vl calipers fit on standard 71 1600 struts????? what ealse is needed ? if so, that suits me as i've recently replaced the springs, strut inserts and bearings on the standard 71 1600 struts. thanks. dunc. >From: "Terry Rudd" <[EMAIL PROTECTED]> >Reply-To: [EMAIL PROTECTED] >To: <[EMAIL PROTECTED]> >Subject: RE: brake conversion. >Date: Sun, 23 Mar 2003 01:21:02 +1100 > >Mark, > >I've read this a couple of times and something still doesn't quite make >sense to me here - a 180B/1600 strut has calliper mount bolt spacing of >76.2mm (3") which is exactly the sized struts that you've asked about. VL >callipers are 76.2mm bolt spaced (that's why they're used with the Magna or >Verada conversions), and the availability of good low cost pads just about >anywhere in Oz. The other size calliper that Holden uses on it's family >type >VT/VU Commydore is 3.5" bolt spaced and they fit 200B/240K/C210 etc Nissan >struts. I'm not talking about Clubsport & SS models, they use AP callipers >which are very different again. The measurements that I've quoted are >"centre bolt to centre bolt" - may be you've not quoted the measurements in >like terms? > >regards >Terry > >-----Original Message----- >From: [EMAIL PROTECTED] >[mailto:[EMAIL PROTECTED] Behalf Of mark krawczuk >Sent: Friday, 14 March 2003 12:56 PM >To: [EMAIL PROTECTED] >Subject: brake conversion. > > >hi, i am trying to setup a verada front brake setup on my 1600, but >instead of using vl calipers, i am using vt calipers. > they will not bolt up to 180b or 1600 struts, as i was told. >i used a verniers to measure the holes on the vt caliper, >from the outer side of each hole it measures approx (3.475") 88mm. >from the inner side of each hole it measures approx (2.52") 64mm. >the holes are 12 mm big. >therefore i need a strut with caliper mounting holes approx 76 mm apart. >is there a strut suitable, or do i need a adapter etc,,,,,????? > > > mark k > > > > _________________________________________________________________ Hotmail now available on Australian mobile phones. Go to http://ninemsn.com.au/mobilecentral/hotmail_mobile.asp --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/[EMAIL PROTECTED]/ ---------------------------------------------------------------------
