hi rick,
i have a pair of webers 40mm but i dont have a inlet manifold.do you know where can i
get one from,or anyone out there has one of them.
our 1/4 mile is on the 29/02 and i wana run my car in this race.
-----Original Message-----
From: Rick Clough [mailto:[EMAIL PROTECTED]
Sent: Tuesday, February 03, 2004 11:24 PM
To: [EMAIL PROTECTED]
Subject: Re: manifold brace for Fj20et
Mohit,
Welcome to us "Aussi" Datsun lovers. I am sure some of us will be able to
help you get your 1600 atmo engine going harder. Do you have access to a
multi carb manifold and carbs? A pair of 45mm Webers jetted to suit your
engine is a good start.if you can get them.
The factory "SSS" twin hitachi carbs, manifold, airfilter and throttle
linkage is a good lower priced road use option. These can be found in
Australia usually for about $A150.
Inlet manifold and exhaust improvements will help breathing, followed by
head porting and a "bigger" camshaft and valves, everything to help it
breath better.
Because it will rev harder with better breathing you should balance the
pistons, rods, crank and fit a lightened and balanced flywheel.for
reliability if you plan to use higher revs (above 6000).
----- Original Message -----
From: "Mohit K. Autar" <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Sent: Friday, 30 January 2004 11:16 AM
Subject: RE: manifold brace for Fj20et
hi guys,
sorry,coz i will be of the topic.i have a datsun 1400 and i wana fit a
modified L16 engine in it and run it for 1/4 mile.does anyone know what time
i will be doing.
if anyone can guide what all to do.i wana built a budget built car.i have
most of the staff with me to get power.
-----Original Message-----
From: amr [mailto:[EMAIL PROTECTED]
Sent: Thursday, January 29, 2004 11:03 PM
To: Ozdat
Subject: RE: manifold brace for Fj20et
think it's the same as my FJ20E ones, the goes from the engine mount up
to 2 points on the inlet, also there is another one that goes from back
of alternator to inlet too,
I might be able to take some pictures of them if some one wants, i have
a set off my spare engine
Anthony
ps yes these are factory braces
-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] Behalf Of Mark
Sent: 29 January 2004 10:43
To: amr
Subject: WTB: manifold brace for Fj20et
I spotted a very neat brace which I presume is a factory item,
supporting those long inlet runners on an FJ20ET. anyone got one they
wanna get rid of, as I'm fearful of eventual cracking due to lack of
support on my car. IIRC braces bolts to side of block, not to the car
like some DIY set-ups which would have to be flexible mounts.
Mark (Canberra)
On Thursday, January 29, 2004, at 08:55 PM, maldat wrote:
> Just go to any Nissan dealer and ask for part number 14035-N6900.
>
>
> Malcolm
>
> P.S
> make sure you use the steel brace that goes from end of the EFI inlet
> to
> engine mount ,,Thus the inlet will not wobble and come loose,, (just
> thought
> I should add that,Most people forget about it )
>
>
> ----- Original Message -----
> From: "Andrew Greenbury" <[EMAIL PROTECTED]>
> To: <[EMAIL PROTECTED]>
> Sent: Thursday, January 29, 2004 7:14 PM
> Subject: Re: EFI L series manifold gasket
>
>
>> Hi Malcolm,
>>
>> I don't believe we got the S110 in Aust, or at least with a different
>> engine, so having trouble getting the correct gasket :(
>>
>> Andrew
>>
>>> Use the right gasket.
>>> L18E from a S110 180SX is what to ask for/.
>>>
>>> Malcolm
>>> ----- Original Message -----
>>> From: "Andrew Greenbury" <[EMAIL PROTECTED]>
>>> To: <[EMAIL PROTECTED]>
>>> Sent: Thursday, January 29, 2004 4:46 PM
>>> Subject: EFI L series manifold gasket
>>>
>>>
>>>> Hi everyone,
>>>>
>>>> Im having trouble getting my recently installed L18 efi manifold to
> seal
>>>> - I used an L20 mani gasket with the top port section cut out for
>>>> the
>>>> injectors. This appears to not leave much material to seal, and it
>>>> seems to be leaking a bit around the top port section.
>>>>
>>>> What gasket has other people used on efi L4s, or should I make a
>>>> custom gasket for the application?
>>>>
>>>> Thanks for any help,
>>>> Andrew
>>>>
>>>>
>>>>
>>>>
>>>>
>>>
>>>
>>>
>>>
>>>
>>
>>
>>
>>
>>
>>
>
>
>
>
>
--membersozdat-------------------------------------------------------
OZDAT Mailing List Please Note:-
Send (un)subscribe requests to [EMAIL PROTECTED]
Send submissions to [EMAIL PROTECTED]
No unauthorised redistribution of this email
http://www.ozdat.com/ozdatonline/index.htm
http://www.ozdat.com/ozdatonline/listindex.html
http://www.mail-archive.com/[EMAIL PROTECTED]/
---------------------------------------------------------------------
This email and any files transmitted with it are confidential and intended solely for
the use of the individual or entity to whom they are addressed. If you have received
this mail in error, please notify the System Administrator. Please note that any views
or opinions presented in this mail are solely those of the author and do not
necessarily
represent those of the Institute. Finally the recipient should check this mail and any
attachment for the presence of viruses. FIT has a virus detection in place and makes
every reasonable effort to ensure that this message is free from viruses. FIT accepts
no liability for any damage caused by any virus transmitted by this mail
