On Wed, Dec 07, 2022 at 03:43:12PM -0600, Andrew Davis via
lists.yoctoproject.org wrote:
> The WIC image for K3 depends on the TI-SCI firmware, on AM65x and J721e
> also the bootloader. Make this clear by only depending on firmware in
> the base k3.inc file, then adding the bootloader dependency in AM65x and
> J721e specific includes.
>
> Remove unneeded overrides from the evm level files.
>
> Remove do_image_tar dependencies as the tar files do not include
> the bootloader nor TI-SCI firmware, only the boot partition of
> the WIC file needs these.
>
> Signed-off-by: Andrew Davis <[email protected]>
> ---
> diff --git a/meta-ti-bsp/conf/machine/include/j721e.inc
> b/meta-ti-bsp/conf/machine/include/j721e.inc
> index 12ee0c90..6322fe46 100644
> --- a/meta-ti-bsp/conf/machine/include/j721e.inc
> +++ b/meta-ti-bsp/conf/machine/include/j721e.inc
> @@ -9,6 +9,17 @@ PREFERRED_PROVIDER_virtual/libgles2 ?= "ti-img-rogue-umlibs"
> PREFERRED_PROVIDER_virtual/libgbm ?= "ti-img-rogue-umlibs"
> PREFERRED_PROVIDER_virtual/gpudriver ?= "ti-img-rogue-driver"
>
> +# On J721e the file tiboot3.bin comes from the bootloader not ti-sci-fw
> +do_image_wic[mcdepends] += "mc::k3r5:virtual/bootloader:do_deploy"
> +
> +# Default sysfw.itb on J721e is for SR1.1
> +BBMULTICONFIG += "k3r5-sr1-1"
There's a slight problem - k3r5-sr1-1 multiconfig previously only applied to
the HS j721e-hs-evm device, but not the GP j721e-evm, see below.
Hence there's no corresponding k3r5 config j721e-evm-k3r5-sr1-1.conf exists,
only the one for the HS - j721e-hs-evm-k3r5-sr1-1.conf
Since you moved the above BBMULTICONFIG line into the common j721e.inc, it now
breaks with the error:
MACHINE=j721e-evm-k3r5-sr1-1 is invalid. Please set a valid MACHINE in your
local.conf, environment or other configuration file.
I can re-spin this series with a fix, so it's easier for Ryan to apply...
> +do_image_wic[mcdepends] += "mc::k3r5-sr1-1:ti-sci-fw:do_deploy"
> +IMAGE_BOOT_FILES += "sysfw.itb"
> +
> +# Since default sysfw.itb on J721e is for SR1.1, add a version for SR1.0
> +IMAGE_BOOT_FILES += "sysfw-j721e-evm.itb"
> +
> TFA_BOARD = "generic"
>
> OPTEEMACHINE = "k3-j721e"
<snip>
> diff --git a/meta-ti-bsp/conf/machine/j721e-evm.conf
> b/meta-ti-bsp/conf/machine/j721e-evm.conf
> index d28d16d1..fe28e6f5 100644
> --- a/meta-ti-bsp/conf/machine/j721e-evm.conf
> +++ b/meta-ti-bsp/conf/machine/j721e-evm.conf
> @@ -7,9 +7,6 @@ require conf/machine/include/j721e.inc
> SERIAL_CONSOLES = "115200;ttyS2 115200;ttyS3"
> SERIAL_CONSOLES_CHECK = "${SERIAL_CONSOLES}"
>
> -# Since J721e does not support multi-cert tiboot3.bin add standalone
> sysfw.itb
> -IMAGE_BOOT_FILES += "sysfw.itb"
> -
> KERNEL_DEVICETREE = " \
> ti/k3-j721e-common-proc-board.dtb \
> ti/k3-j721e-common-proc-board-infotainment.dtbo \
> diff --git a/meta-ti-bsp/conf/machine/j721e-hs-evm.conf
> b/meta-ti-bsp/conf/machine/j721e-hs-evm.conf
> index 9ef7b86a..acd5ca18 100644
> --- a/meta-ti-bsp/conf/machine/j721e-hs-evm.conf
> +++ b/meta-ti-bsp/conf/machine/j721e-hs-evm.conf
> @@ -18,10 +18,3 @@ SPL_BINARY = "tispl.bin_HS"
> UBOOT_BINARY = "u-boot.img_HS"
> UBOOT_SYMLINK = "u-boot.img"
> SYSFW_SYMLINK = ""
> -
> -BBMULTICONFIG += "k3r5-sr1-1"
> -
> -# Since default sysfw.itb on J721e is for SR1.1, add a version for SR1.0
> -IMAGE_BOOT_FILES += "sysfw-j721e-evm.itb"
> -do_image_wic[mcdepends] += "mc::k3r5-sr1-1:ti-sci-fw:do_deploy"
> -do_image_tar[mcdepends] += "mc::k3r5-sr1-1:ti-sci-fw:do_deploy"
-=-=-=-=-=-=-=-=-=-=-=-
Links: You receive all messages sent to this group.
View/Reply Online (#15585):
https://lists.yoctoproject.org/g/meta-ti/message/15585
Mute This Topic: https://lists.yoctoproject.org/mt/95525682/21656
Group Owner: [email protected]
Unsubscribe: https://lists.yoctoproject.org/g/meta-ti/unsub
[[email protected]]
-=-=-=-=-=-=-=-=-=-=-=-
