ah, that explains it then.

Okay, so I've made a bit more progress. I added some more packages to my build 
my appending this to my build/conf/local.conf

CORE_IMAGE_EXTRA_INSTALL += "wpa-supplicant"
CORE_IMAGE_EXTRA_INSTALL += "wireless-tools"
#CORE_IMAGE_EXTRA_INSTALL += "resolveconf"
CORE_IMAGE_EXTRA_INSTALL += "openssl"
CORE_IMAGE_EXTRA_INSTALL += "zeroconf"
CORE_IMAGE_EXTRA_INSTALL += "modutils-initscripts"
CORE_IMAGE_EXTRA_INSTALL += "update-modules"


This gives me depmod and the rest.  Now I can manually load drivers and depmod 
-a succeeds.  However, I still can't activate the wlan0.   ifup wlan0 gives me

root@overo:~# ifup wlan0
Could not read interface wlan0 flags: No such device
WEXT: Could not set interface 'wlan0' UP
wlan0: Failed to initialize driver interface

On a hunch I looked at /var/log/messages and it says near the end:


Jul 30 23:17:03 overo user.info kernel: libertas_sdio: Libertas SDIO driver
Jul 30 23:17:03 overo user.info kernel: libertas_sdio: Copyright Pierre Ossman
Jul 30 23:17:03 overo user.err kernel: libertas_sdio: failed to find firmware 
(-2)


You mentioned the firmware. Where do I get that?


Incidentally, I don't get all of the kernel boot messages when my gumstix 
boots.  It says 

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

Yocto (Built by Poky 7.0) 1.2+snapshot-20120730 overo ttyO2

overo login:


And then I'm at the login prompt.  I'm assuming there is some boot setting 
which controls this? All of the messages are showing up in /var/log/messages, 
however.

Thanks,

 Josh


On Jul 30, 2012, at 12:42 PM, ext Denys Dmytriyenko wrote:

> On Mon, Jul 30, 2012 at 07:10:23PM +0000, [email protected] wrote:
>> Hmm. I don't see to have depmod installed.  Perhaps that is part of my 
>> problem. What package would I need to add to the minimal-core-image to get 
>> that?
> 
> Josh,
> 
> core-image-minimal uses busybox for tools like insmod and modprobe. The 
> default configuration for busybox does not have depmod enabled. As of 
> module-init-tools, they are being built, but not installed on the filesystem. 
> So, you can either modify busybox config to enable depmod, or add 
> module-init-tools-depmod package to your filesystem. The new way is to use 
> kmod, which is available in oe-core master, or meta-oe in denzil. But oe-core 
> master setup is broken for me at the moment, so I can't verify that kmod is 
> included. At least it's not listed in the image/task...
> 
> Denys
> 
> 
>> On Jul 30, 2012, at 1:07 AM, ext Enrico wrote:
>> 
>>> On Sat, Jul 28, 2012 at 9:30 PM,  <[email protected]> wrote:
>>>> This does work. When I boot the wpa stuff is included but I still don't 
>>>> have a network driver loaded.  If I include the built 
>>>> modules-3.2.19-r0-overo.tgz in my rootfs I can cd into the directory with 
>>>> all of the modules.  However insmod libertas.ko fails with
>>>> 
>>>>       insmod: can't insert 'libertas_tf_usb.ko': unknown symbol in module, 
>>>> or unknown parameter
>>>> 
>>>> and modprobe fails with
>>>> 
>>>>       modprobe: module libertas not found in modules.dep
>>>> 
>>>> 
>>>> So, what should I do to make sure the libertas module is compiled 
>>>> correctly, included in my kernel, and then actually used at runtime?
>>> 
>>> try with "depmod -a" (this must be done only once after you untar the
>>> modules) before modprobe libertas.
>>> 
>>> I am not sure but i think it was "modprobe libertas_sdio", try that
>>> too. And of course you will need the libertas firmware
>>> (sd8686....bin).
>>> 
>>> Enrico
>> 
>> _______________________________________________
>> meta-ti mailing list
>> [email protected]
>> https://lists.yoctoproject.org/listinfo/meta-ti

_______________________________________________
meta-ti mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/meta-ti

Reply via email to