Thank you everyone for your help. I finally got it working. After adding those 
extra recipes, doing the usual wifi config with /etc/network/interfaces and 
wpa-supplicant, and running depmod -a I was able get everything in place. 
Adding the magic firmware files extracted from Gumstix's pre-built distro was 
the last piece of the puzzle. When I next rebooted I was already on the 
network.  

So, my question now is "what's up with those sd8686* firmware files? If they 
are required then why aren't they a part of meta-gumstix?  Is it something 
special that can only be legally downloaded from Gumstix.com? 

thank you everyone.
        Josh


On Jul 30, 2012, at 5:31 PM, ext [email protected] wrote:

> ah, that explains it then.
> 
> Okay, so I've made a bit more progress. I added some more packages to my 
> build my appending this to my build/conf/local.conf
> 
> CORE_IMAGE_EXTRA_INSTALL += "wpa-supplicant"
> CORE_IMAGE_EXTRA_INSTALL += "wireless-tools"
> #CORE_IMAGE_EXTRA_INSTALL += "resolveconf"
> CORE_IMAGE_EXTRA_INSTALL += "openssl"
> CORE_IMAGE_EXTRA_INSTALL += "zeroconf"
> CORE_IMAGE_EXTRA_INSTALL += "modutils-initscripts"
> CORE_IMAGE_EXTRA_INSTALL += "update-modules"
> 
> 
> This gives me depmod and the rest.  Now I can manually load drivers and 
> depmod -a succeeds.  However, I still can't activate the wlan0.   ifup wlan0 
> gives me
> 
> root@overo:~# ifup wlan0
> Could not read interface wlan0 flags: No such device
> WEXT: Could not set interface 'wlan0' UP
> wlan0: Failed to initialize driver interface
> 
> On a hunch I looked at /var/log/messages and it says near the end:
> 
> 
> Jul 30 23:17:03 overo user.info kernel: libertas_sdio: Libertas SDIO driver
> Jul 30 23:17:03 overo user.info kernel: libertas_sdio: Copyright Pierre Ossman
> Jul 30 23:17:03 overo user.err kernel: libertas_sdio: failed to find firmware 
> (-2)
> 
> 
> You mentioned the firmware. Where do I get that?
> 
> 
> Incidentally, I don't get all of the kernel boot messages when my gumstix 
> boots.  It says 
> 
> Starting kernel ...
> 
> Uncompressing Linux... done, booting the kernel.
> 
> Yocto (Built by Poky 7.0) 1.2+snapshot-20120730 overo ttyO2
> 
> overo login:
> 
> 
> And then I'm at the login prompt.  I'm assuming there is some boot setting 
> which controls this? All of the messages are showing up in /var/log/messages, 
> however.
> 
> Thanks,
> 
> Josh
> 
> 
> On Jul 30, 2012, at 12:42 PM, ext Denys Dmytriyenko wrote:
> 
>> On Mon, Jul 30, 2012 at 07:10:23PM +0000, [email protected] wrote:
>>> Hmm. I don't see to have depmod installed.  Perhaps that is part of my 
>>> problem. What package would I need to add to the minimal-core-image to get 
>>> that?
>> 
>> Josh,
>> 
>> core-image-minimal uses busybox for tools like insmod and modprobe. The 
>> default configuration for busybox does not have depmod enabled. As of 
>> module-init-tools, they are being built, but not installed on the 
>> filesystem. 
>> So, you can either modify busybox config to enable depmod, or add 
>> module-init-tools-depmod package to your filesystem. The new way is to use 
>> kmod, which is available in oe-core master, or meta-oe in denzil. But 
>> oe-core 
>> master setup is broken for me at the moment, so I can't verify that kmod is 
>> included. At least it's not listed in the image/task...
>> 
>> Denys
>> 
>> 
>>> On Jul 30, 2012, at 1:07 AM, ext Enrico wrote:
>>> 
>>>> On Sat, Jul 28, 2012 at 9:30 PM,  <[email protected]> wrote:
>>>>> This does work. When I boot the wpa stuff is included but I still don't 
>>>>> have a network driver loaded.  If I include the built 
>>>>> modules-3.2.19-r0-overo.tgz in my rootfs I can cd into the directory with 
>>>>> all of the modules.  However insmod libertas.ko fails with
>>>>> 
>>>>>      insmod: can't insert 'libertas_tf_usb.ko': unknown symbol in module, 
>>>>> or unknown parameter
>>>>> 
>>>>> and modprobe fails with
>>>>> 
>>>>>      modprobe: module libertas not found in modules.dep
>>>>> 
>>>>> 
>>>>> So, what should I do to make sure the libertas module is compiled 
>>>>> correctly, included in my kernel, and then actually used at runtime?
>>>> 
>>>> try with "depmod -a" (this must be done only once after you untar the
>>>> modules) before modprobe libertas.
>>>> 
>>>> I am not sure but i think it was "modprobe libertas_sdio", try that
>>>> too. And of course you will need the libertas firmware
>>>> (sd8686....bin).
>>>> 
>>>> Enrico
>>> 
>>> _______________________________________________
>>> meta-ti mailing list
>>> [email protected]
>>> https://lists.yoctoproject.org/listinfo/meta-ti
> 
> _______________________________________________
> meta-ti mailing list
> [email protected]
> https://lists.yoctoproject.org/listinfo/meta-ti

_______________________________________________
meta-ti mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/meta-ti

Reply via email to