Below I provide full information from ifconfig, route and a full dmesg. By the
way, I think this is a BUG in the wireless firmware that I'm using (downloaded
from the OpenBSD firmware site). I say this because I found this line in the
dmesg output: wpi0: fatal firmware error
So below are the outputs.
ifconfig output:
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 32768
index 4 priority 0 llprio 3
groups: lo
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4
inet 127.0.0.1 netmask 0xff000000
re0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:1f:16:03:90:fe
index 1 priority 0 llprio 3
media: Ethernet autoselect (none)
status: no carrier
wpi0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:1f:3c:8d:aa:a2
index 2 priority 4 llprio 3
groups: wlan egress
media: IEEE802.11 autoselect (DS1 mode 11g)
status: active
ieee80211: nwid zsolt chan 11 bssid 70:4f:57:2c:b1:04 -42dBm wpakey <not
displayed> wpaprotos wpa2 wpaakms psk wpaciphers ccmp wpagroupcipher ccmp
inet 192.168.0.101 netmask 0xffffff00 broadcast 192.168.0.255
enc0: flags=0<>
index 3 priority 0 llprio 3
groups: enc
status: active
pflog0: flags=141<UP,RUNNING,PROMISC> mtu 33136
index 5 priority 0 llprio 3
groups: pflog
route -n show output:
Routing tables
Internet:
Destination Gateway Flags Refs Use Mtu Prio Iface
default 192.168.0.1 UGS 3 450 - 12 wpi0
224/4 127.0.0.1 URS 0 12 32768 8 lo0
127/8 127.0.0.1 UGRS 0 0 32768 8 lo0
127.0.0.1 127.0.0.1 UHhl 1 3101 32768 1 lo0
192.168.0/24 192.168.0.101 UCn 1 0 - 8 wpi0
192.168.0.1 70:4f:57:2c:b1:04 UHLch 2 267 - 7 wpi0
192.168.0.101 00:1f:3c:8d:aa:a2 UHLl 0 831 - 1 wpi0
192.168.0.255 192.168.0.101 UHb 0 0 - 1 wpi0
Internet6:
Destination Gateway Flags Refs
Use Mtu Prio Iface
::/96 ::1 UGRS 0
0 32768 8 lo0
::/104 ::1 UGRS 0
0 32768 8 lo0
::1 ::1 UHhl 14
34 32768 1 lo0
::127.0.0.0/104 ::1 UGRS 0
0 32768 8 lo0
::224.0.0.0/100 ::1 UGRS 0
0 32768 8 lo0
::255.0.0.0/104 ::1 UGRS 0
0 32768 8 lo0
::ffff:0.0.0.0/96 ::1 UGRS 0
0 32768 8 lo0
2002::/24 ::1 UGRS 0
0 32768 8 lo0
2002:7f00::/24 ::1 UGRS 0
0 32768 8 lo0
2002:e000::/20 ::1 UGRS 0
0 32768 8 lo0
2002:ff00::/24 ::1 UGRS 0
0 32768 8 lo0
fe80::/10 ::1 UGRS 0
0 32768 8 lo0
fec0::/10 ::1 UGRS 0
0 32768 8 lo0
fe80::1%lo0 fe80::1%lo0 UHl 0
0 32768 1 lo0
ff01::/16 ::1 UGRS 0
0 32768 8 lo0
ff01::%lo0/32 ::1 Um 0
1 32768 4 lo0
ff02::/16 ::1 UGRS 0
0 32768 8 lo0
ff02::%lo0/32 ::1 Um 0
1 32768 4 lo0
dmesg output:
OpenBSD 6.2 (GENERIC.MP) #5: Fri Feb 2 23:02:19 CET 2018
r...@syspatch-62-amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
real mem = 2121072640 (2022MB)
avail mem = 2049826816 (1954MB)
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.4 @ 0x7f6df000 (43 entries)
bios0: vendor Phoenix Technologies LTD version "V1.10" date 05/21/2009
bios0: FUJITSU SIEMENS AMILO Li 2735
acpi0 at bios0: rev 2
acpi0: sleep states S0 S3 S4 S5
acpi0: tables DSDT FACP HPET MCFG TCPA TMOR SLIC APIC BOOT SSDT SSDT SSDT SSDT
acpi0: wakeup devices LID0(S3) SLPB(S3) LANC(S4) HDEF(S4) PXSX(S4) PXSX(S4)
PXSX(S4) PXSX(S4) PXSX(S4) PXSX(S4) USB1(S3) USB2(S3) USB3(S3) USB4(S3)
USB5(S3) EHC1(S3) [...]
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpihpet0 at acpi0: 14318179 Hz
acpimcfg0 at acpi0 addr 0xe0000000, bus 0-255
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Core(TM)2 Duo CPU T5750 @ 2.00GHz, 1995.61 MHz
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM,NXE,LONG,LAHF,PERF,SENSOR
cpu0: 2MB 64b/line 8-way L2 cache
cpu0: smt 0, core 0, package 0
mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
cpu0: apic clock running at 166MHz
cpu0: mwait min=64, max=64, C-substates=0.2.2.2.2, IBE
cpu1 at mainbus0: apid 1 (application processor)
cpu1: Intel(R) Core(TM)2 Duo CPU T5750 @ 2.00GHz, 1995.22 MHz
cpu1:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM,NXE,LONG,LAHF,PERF,SENSOR
cpu1: 2MB 64b/line 8-way L2 cache
cpu1: smt 0, core 1, package 0
ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 2 (RP01)
acpiprt2 at acpi0: bus 4 (RP02)
acpiprt3 at acpi0: bus 8 (RP03)
acpiprt4 at acpi0: bus -1 (RP04)
acpiprt5 at acpi0: bus -1 (RP05)
acpiprt6 at acpi0: bus -1 (RP06)
acpiprt7 at acpi0: bus 16 (PCIB)
acpiec0 at acpi0
acpicpu0 at acpi0: !C3(100@57 mwait.3@0x30), !C2(500@1 mwait.1@0x10), C1(1000@1
mwait.1), PSS
acpicpu1 at acpi0: !C3(100@57 mwait.3@0x30), !C2(500@1 mwait.1@0x10), C1(1000@1
mwait.1), PSS
acpitz0 at acpi0: critical temperature is 85 degC
acpitz1 at acpi0: critical temperature is 126 degC
"*pnp0c14" at acpi0 not configured
acpibtn0 at acpi0: LID0
acpibtn1 at acpi0: SLPB
acpibat0 at acpi0: BAT0 not present
acpiac0 at acpi0: AC unit online
"SYN0310" at acpi0 not configured
acpivideo0 at acpi0: VGA_
acpivideo1 at acpi0: GFX0
acpivout0 at acpivideo1: DD03
cpu0: Enhanced SpeedStep 1995 MHz: speeds: 2000, 1667, 1333, 1000 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel GM965 Host" rev 0x03
inteldrm0 at pci0 dev 2 function 0 "Intel GM965 Video" rev 0x03
drm0 at inteldrm0
intagp0 at inteldrm0
agp0 at intagp0: aperture at 0xd0000000, size 0x10000000
inteldrm0: msi
inteldrm0: 848x480, 32bpp
wsdisplay0 at inteldrm0 mux 1: console (std, vt100 emulation)
wsdisplay0: screen 1-5 added (std, vt100 emulation)
"Intel GM965 Video" rev 0x03 at pci0 dev 2 function 1 not configured
uhci0 at pci0 dev 26 function 0 "Intel 82801H USB" rev 0x04: apic 2 int 16
uhci1 at pci0 dev 26 function 1 "Intel 82801H USB" rev 0x04: apic 2 int 21
ehci0 at pci0 dev 26 function 7 "Intel 82801H USB" rev 0x04: apic 2 int 18
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Intel EHCI root hub" rev 2.00/1.00
addr 1
azalia0 at pci0 dev 27 function 0 "Intel 82801H HD Audio" rev 0x04: msi
azalia0: codecs: Realtek ALC268
audio0 at azalia0
ppb0 at pci0 dev 28 function 0 "Intel 82801H PCIE" rev 0x04: msi
pci1 at ppb0 bus 2
re0 at pci1 dev 0 function 0 "Realtek 8101E" rev 0x01: RTL8101E (0x3400), msi,
address 00:1f:16:03:90:fe
rlphy0 at re0 phy 7: RTL8201L 10/100 PHY, rev. 1
ppb1 at pci0 dev 28 function 1 "Intel 82801H PCIE" rev 0x04: msi
pci2 at ppb1 bus 4
ppb2 at pci0 dev 28 function 2 "Intel 82801H PCIE" rev 0x04: msi
pci3 at ppb2 bus 8
wpi0 at pci3 dev 0 function 0 "Intel PRO/Wireless 3945ABG" rev 0x02: msi, MoW2,
address 00:1f:3c:8d:aa:a2
uhci2 at pci0 dev 29 function 0 "Intel 82801H USB" rev 0x04: apic 2 int 23
uhci3 at pci0 dev 29 function 1 "Intel 82801H USB" rev 0x04: apic 2 int 19
uhci4 at pci0 dev 29 function 2 "Intel 82801H USB" rev 0x04: apic 2 int 18
ehci1 at pci0 dev 29 function 7 "Intel 82801H USB" rev 0x04: apic 2 int 23
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 configuration 1 interface 0 "Intel EHCI root hub" rev 2.00/1.00
addr 1
ppb3 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xf4
pci4 at ppb3 bus 16
pcib0 at pci0 dev 31 function 0 "Intel 82801HBM LPC" rev 0x04
pciide0 at pci0 dev 31 function 1 "Intel 82801HBM IDE" rev 0x04: DMA, channel 0
configured to compatibility, channel 1 configured to compatibility
atapiscsi0 at pciide0 channel 0 drive 0
scsibus1 at atapiscsi0: 2 targets
cd0 at scsibus1 targ 0 lun 0: <TSSTcorp, CDDVDW TS-L632H, AS04> ATAPI 5/cdrom
removable
cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
pciide1 at pci0 dev 31 function 2 "Intel 82801HBM SATA" rev 0x04: DMA, channel
0 configured to native-PCI, channel 1 configured to native-PCI
pciide1: using apic 2 int 19 for native-PCI interrupt
wd0 at pciide1 channel 0 drive 0: <WDC WD1600BEVT-22ZCT0>
wd0: 16-sector PIO, LBA48, 152627MB, 312581808 sectors
wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 6
ichiic0 at pci0 dev 31 function 3 "Intel 82801H SMBus" rev 0x04: apic 2 int 19
iic0 at ichiic0
spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM non-parity PC2-5300CL5 SO-DIMM
spdmem1 at iic0 addr 0x52: 1GB DDR2 SDRAM non-parity PC2-5300CL5 SO-DIMM
usb2 at uhci0: USB revision 1.0
uhub2 at usb2 configuration 1 interface 0 "Intel UHCI root hub" rev 1.00/1.00
addr 1
usb3 at uhci1: USB revision 1.0
uhub3 at usb3 configuration 1 interface 0 "Intel UHCI root hub" rev 1.00/1.00
addr 1
usb4 at uhci2: USB revision 1.0
uhub4 at usb4 configuration 1 interface 0 "Intel UHCI root hub" rev 1.00/1.00
addr 1
usb5 at uhci3: USB revision 1.0
uhub5 at usb5 configuration 1 interface 0 "Intel UHCI root hub" rev 1.00/1.00
addr 1
usb6 at uhci4: USB revision 1.0
uhub6 at usb6 configuration 1 interface 0 "Intel UHCI root hub" rev 1.00/1.00
addr 1
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5 irq 1 irq 12
pckbd0 at pckbc0 (kbd slot)
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
wsmouse0 at pms0 mux 0
pms0: Synaptics touchpad, firmware 6.3, 0x1280b1 0xa04000
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
vblank wait timed out on crtc 1
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
root on wd0a (eb090922f0f6e0ef.a) swap on wd0b dump on wd0b
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
wpi0: fatal firmware error
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
vblank wait timed out on crtc 1
On Sunday, February 11, 2018 9:33 PM, Tom Smyth <tom.sm...@wirelessconnect.eu>
wrote:
Hi Zsolt,
in order to help us help you try to include more information
output from dmesg , what is your network configuration
ifconfig
route -n show
there is no default queuing in OpenBSD that would limit you that
badly
Thanks
On 11 February 2018 at 19:15, Zsolt Kantor <zsoltkan...@yahoo.co.uk> wrote:
> Hello,
> I'm using the latest release. Where the dl speed in other OS is approx. 1.4
> MB/s in BSD is only approx. 240 KB/s. Why is this? Is about a setting in some
> config file that limits download/traffic rate?
>
> Thanks.
>
--
Kindest regards,
Tom Smyth
Mobile: +353 87 6193172
The information contained in this E-mail is intended only for the
confidential use of the named recipient. If the reader of this message
is not the intended recipient or the person responsible for
delivering it to the recipient, you are hereby notified that you have
received this communication in error and that any review,
dissemination or copying of this communication is strictly prohibited.
If you have received this in error, please notify the sender
immediately by telephone at the number above and erase the message
You are requested to carry out your own virus check before
opening any attachment.
