Hello
Do you have any reason to not use pxeboot? Take a look in /usr/mdec.
Else, take a look at flashdist-20060413.tar
residing here http://www.nmedia.net/~chris/soekris/
Hope this is readable although I'm writing it in the virusmanager outlook
express.
/regards from Sweden
----- Original Message -----
From: "Marc Peters" <[EMAIL PROTECTED]>
To: <[email protected]>
Sent: Tuesday, May 30, 2006 2:08 PM
Subject: can't get soekris 4801 to boot via pxe
hello misc,
i bought a soekris 4801 from wim and wanted to install it via net. when i
boot the box it gets it ip-address and when it comes to load bsd.rd it
loads the kernel but hangs during load:
comBIOS ver. 1.28 20050529 Copyright (C) 2000-2005 Soekris Engineering.
net4801
0128 Mbyte Memory CPU Geode 266 Mhz
Pri Sla SILICONSYSTEMS INC 512MB LBA 1011-16-63 509 Mbyte
Slot Vend Dev ClassRev Cmd Stat CL LT HT Base1 Base2 Int
-------------------------------------------------------------------
0:00:0 1078 0001 06000000 0107 0280 00 00 00 00000000 00000000
0:06:0 100B 0020 02000000 0107 0290 00 3F 00 0000E101 A0000000 10
0:07:0 100B 0020 02000000 0107 0290 00 3F 00 0000E201 A0001000 10
0:08:0 100B 0020 02000000 0107 0290 00 3F 00 0000E301 A0002
0:18:2 100B 0502 01018001 0005 0280 00 00 00 00000000 00000000
0:19:0 0E11 A0F8 0C031008 0117 0280 08 38 00 A0003000 00000000 11
4 Seconds to automatic boot. Press Ctrl-P for entering Monitor.
comBIOS Monitor. Press ? for help.
> boot F0
NSC DP83815/DP83816 Fast Ethernet UNDI, v1.03
Copyright (C) 2002, 2003 National Semiconductor Corporation
All rights reserved.
Pre-boot eXecution Environment PXE-2.0 (build 082)
Copyright (C) 1997-2000 Intel Corporation
CLIENT MAC ADDR: 00 00 24 C6 5C F8
CLIENT IP: 192.168.83.3 MASK: 255.255.255.0 DHCP IP: 192.168.83.208
GATEWAY IP: 192.168.83.1
probing: pc0 com0 com1 pci pxe![2.1] mem[639K 127M a20=on]
disk: hd0+*
net: mac 00:00:24:c6:5c:f8, ip 192.168.83.3, server 192.168.83.208
>> OpenBSD/i386 PXEBOOT 1.07
switching console to com0
>> OpenBSD/i386 PXEBOOT 1.07
booting tftp:bsd.rd: 4435508+740284 [52+155376+141982]=0x538528
entry point at 0x100120
~$f$~xxf$~$f$8~8~$f$f$
the tftpd resides on a 3.9 and the bsd.rd kernel is from 3.9-RELEASE. i
installed the tftpd as explained in the faq and this is my
/tftpboot/etc/boot.conf:
~ # cat /tftpboot/etc/boot.conf
set tty com0
boot bsd.rd
same thing with latest snapshot:
probing: pc0 com0 com1 pci pxe![2.1] mem[639K 127M a20=on]
disk: hd0+*
net: mac 00:00:24:c6:5c:f8, ip 192.168.83.3, server 192.168.83.208
>> OpenBSD/i386 PXEBOOT 1.07
switching console to com0
>> OpenBSD/i386 PXEBOOT 1.07
booting tftp:bsd.rd: 4539860+740228 [52+159968+145900]=0x553dcc
entry point at 0x200120
~$f$~~xxf$~$f$8~8~$f$f$
anyone has any ideas to point me in the correct direction?
TIA,
marc
