On Tue, Jul 1, 2008 at 2:31 PM, Eric Dillenseger
<[EMAIL PROTECTED]> wrote:
> I bought one of these and tried to install openbsd on it.
> My first try was with 4.3 bsd booting over PXE.
> As the ethernet wasn't recognized by the kernel I installed using a
> usb thumb drive because I hadn't found how to boot from a usb device
> at this moment.
> Although the kernel claimed to recognize the atheros wireless card, I
> couldn't use it (ath%d: ath_chan_set: unable to reset channel %u (%u
> Mhz)).
> Now I'm trying to boot bsd from a snapshot (as of yesterday 21:00
> GMT+2) but the kernel hang on the sata driver apparently
>
> pciide0 at pci0 dev 31 function 2 "Intel 82801FBM SATA" rev 0x04: DMA,
> channel 0 wired to compatibility, channel 1 wired to compatibility).
>
> Surprisingly, I tried and successfully booted bsd.mp a few times, but
> it sometimes hang a little further on
>
> npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16.
>
> And sometimes it inverts the SDCard slot and the usb disk so it's
> kinda difficult to get a properly running box yet to test.
>
> I tried with bsd.rd and was able to install a working system and
> again, booting bsd ain't working and bsd.mp often hangs on npx0 and
> sometimes(rarely) boots successfully.
>
> Here's a dmesg:
> OpenBSD 4.3-current (GENERIC.MP) #776: Sun Jun 29 11:34:39 MDT 2008
> [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC.MP
> cpu0: Intel(R) Celeron(R) M processor 900MHz ("GenuineIntel" 686-class) 901
> MHz
> cpu0:
> FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF
> real mem = 1064398848 (1015MB)
> avail mem = 1020956672 (973MB)
> mainbus0 at root
> bios0 at mainbus0: AT/286+ BIOS, date 05/12/08, BIOS32 rev. 0 @
> 0xf0010, SMBIOS rev. 2.5 @ 0xf06f0 (37 entries)
> bios0: vendor American Megatrends Inc. version "0501" date 05/12/2008
> bios0: ASUSTeK Computer INC. 900
> apm0 at bios0: Power Management spec V1.2
> apm0: AC on, battery charge unknown
> acpi at bios0 function 0x0 not configured
> pcibios0 at bios0: rev 3.0 @ 0xf0000/0x10000
> pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf7410/176 (9 entries)
> pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82801FB LPC" rev 0x00)
> pcibios0: PCI bus #5 is the last bus
> bios0: ROM list: 0xc0000/0xf800!
> mainbus0: Intel MP Specification (Version 1.4)
> cpu0 at mainbus0: apid 0 (boot processor)
> cpu0: apic clock running at 100MHz
> mainbus0: bus 0 is type PCI
> mainbus0: bus 1 is type PCI
> mainbus0: bus 2 is type PCI
> mainbus0: bus 3 is type PCI
> mainbus0: bus 4 is type PCI
> mainbus0: bus 5 is type PCI
> mainbus0: bus 6 is type ISA
> ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 20, 24 pins
> pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
> pchb0 at pci0 dev 0 function 0 "Intel 82915GM Host" rev 0x04
> vga1 at pci0 dev 2 function 0 "Intel 82915GM Video" rev 0x04
> wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
> wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
> agp0 at vga1: aperture at 0xd0000000, size 0x10000000
> "Intel 82915GM Video" rev 0x04 at pci0 dev 2 function 1 not configured
> azalia0 at pci0 dev 27 function 0 "Intel 82801FB HD Audio" rev 0x04:
> apic 1 int 16 (irq 5)
> azalia0: codec[s]: Realtek/0x0662
> audio0 at azalia0
> ppb0 at pci0 dev 28 function 0 "Intel 82801FB PCIE" rev 0x04: apic 1
> int 16 (irq 5)
> pci_intr_map: bus 0 dev 28 func 0 pin 4; line 3
> pci_intr_map: no MP mapping found
> pci1 at ppb0 bus 4
> ppb1 at pci0 dev 28 function 1 "Intel 82801FB PCIE" rev 0x04: apic 1
> int 17 (irq 11)
> pci_intr_map: bus 0 dev 28 func 1 pin 4; line 3
> pci_intr_map: no MP mapping found
> pci2 at ppb1 bus 3
> lii0 at pci2 dev 0 function 0 "Attansic Technology L2" rev 0xa0: apic
> 1 int 17 (irq 11), address 00:1f:c6:8f:0d:ee
> ukphy0 at lii0 phy 1: Generic IEEE 802.3u media interface, rev. 2: OUI
> 0x001374, model 0x0002
> ppb2 at pci0 dev 28 function 2 "Intel 82801FB PCIE" rev 0x04: apic 1
> int 18 (irq 10)
> pci_intr_map: bus 0 dev 28 func 2 pin 4; line 3
> pci_intr_map: no MP mapping found
> pci3 at ppb2 bus 1
> ath0 at pci3 dev 0 function 0 "Atheros AR5424" rev 0x01: apic 1 int 18 (irq
> 10)
> ath0: AR5424 14.2 phy 7.0 rf 0.0, WOR0W, address 00:15:af:a7:3d:55
> uhci0 at pci0 dev 29 function 0 "Intel 82801FB USB" rev 0x04: apic 1
> int 23 (irq 7)
> uhci1 at pci0 dev 29 function 1 "Intel 82801FB USB" rev 0x04: apic 1
> int 19 (irq 3)
> uhci2 at pci0 dev 29 function 2 "Intel 82801FB USB" rev 0x04: apic 1
> int 18 (irq 10)
> uhci3 at pci0 dev 29 function 3 "Intel 82801FB USB" rev 0x04: apic 1
> int 16 (irq 5)
> ppb3 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xd4
> pci_intr_map: bus 0 dev 30 func 0 pin 1; line 11
> pci_intr_map: no MP mapping found
> pci_intr_map: bus 0 dev 30 func 0 pin 2; line 3
> pci_intr_map: no MP mapping found
> pci4 at ppb3 bus 5
> ichpcib0 at pci0 dev 31 function 0 "Intel 82801FBM LPC" rev 0x04: PM disabled
> pciide0 at pci0 dev 31 function 2 "Intel 82801FBM SATA" rev 0x04: DMA,
> channel 0 wired to compatibility, channel 1 wired to compatibility
> wd0 at pciide0 channel 1 drive 0: <ASUS-PHISON OB SSD>
> wd0: 1-sector PIO, LBA, 3847MB, 7880544 sectors
> wd1 at pciide0 channel 1 drive 1: <ASUS-PHISON SSD>
> wd1: 1-sector PIO, LBA, 7695MB, 15761088 sectors
> wd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 4
> wd1(pciide0:1:1): using PIO mode 4, Ultra-DMA mode 4
> ichiic0 at pci0 dev 31 function 3 "Intel 82801FB SMBus" rev 0x04: apic
> 1 int 19 (irq 0)
> iic0 at ichiic0
> spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM non-parity PC2-3200CL5 SO-DIMM
> usb0 at uhci0: USB revision 1.0
> uhub0 at usb0 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> usb1 at uhci1: USB revision 1.0
> uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> usb2 at uhci2: USB revision 1.0
> uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> usb3 at uhci3: USB revision 1.0
> uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> isa0 at ichpcib0
> isadma0 at isa0
> pckbc0 at isa0 port 0x60/5
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard, using wsdisplay0
> pmsi0 at pckbc0 (aux slot)
> pckbc0: using irq 12 for aux slot
> wsmouse0 at pmsi0 mux 0
> pcppi0 at isa0 port 0x61
> midi0 at pcppi0: <PC speaker>
> spkr0 at pcppi0
> npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
> mtrr: Pentium Pro MTRR support
> umass0 at uhub1 port 2 configuration 1 interface 0 "SMI Corporation
> USB DISK" rev 2.00/11.00 addr 2
> umass0: using SCSI over Bulk-Only
> scsibus0 at umass0: 2 targets, initiator 0
> sd0 at scsibus0 targ 1 lun 0: <USB, Flash Disk, 1100> SCSI0 0/direct removable
> sd0: 956MB, 121 cyl, 255 head, 63 sec, 512 bytes/sec, 1957888 sec total
> umass1 at uhub2 port 1 configuration 1 interface 0 "ENE UB6225" rev
> 2.00/1.00 addr 2
> umass1: using SCSI over Bulk-Only
> scsibus1 at umass1: 2 targets, initiator 0
> sd1 at scsibus1 targ 1 lun 0: <USB2.0, CardReader SD0, 0100> SCSI0
> 0/direct removable
> sd1: drive offline
> uvideo0 at uhub3 port 2 configuration 1 interface 0 "Chicony
> Electronics Co., Ltd. CNF7129" rev 2.00/15.12 addr 2
> video0 at uvideo0
> softraid0 at root
> root on sd0a swap on sd0b dump on sd0b
This was just discussed: http://marc.info/?l=openbsd-misc&m=121473630601623&w=2
--
# Curt Micol
