We looked at mbalmer's at the hackathon and we were relatively sure it wasn't acpi related. If someone wants to loan/give me one for some time I can try to figure out what is causing the hang.
Contact me off list if you are interested. On Tue, Jul 01, 2008 at 10:28:53PM -0400, Curt Micol wrote: > On Tue, Jul 1, 2008 at 2:31 PM, Eric Dillenseger > <[EMAIL PROTECTED]> wrote: > > I bought one of these and tried to install openbsd on it. > > My first try was with 4.3 bsd booting over PXE. > > As the ethernet wasn't recognized by the kernel I installed using a > > usb thumb drive because I hadn't found how to boot from a usb device > > at this moment. > > Although the kernel claimed to recognize the atheros wireless card, I > > couldn't use it (ath%d: ath_chan_set: unable to reset channel %u (%u > > Mhz)). > > Now I'm trying to boot bsd from a snapshot (as of yesterday 21:00 > > GMT+2) but the kernel hang on the sata driver apparently > > > > pciide0 at pci0 dev 31 function 2 "Intel 82801FBM SATA" rev 0x04: DMA, > > channel 0 wired to compatibility, channel 1 wired to compatibility). > > > > Surprisingly, I tried and successfully booted bsd.mp a few times, but > > it sometimes hang a little further on > > > > npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16. > > > > And sometimes it inverts the SDCard slot and the usb disk so it's > > kinda difficult to get a properly running box yet to test. > > > > I tried with bsd.rd and was able to install a working system and > > again, booting bsd ain't working and bsd.mp often hangs on npx0 and > > sometimes(rarely) boots successfully. > > > > Here's a dmesg: > > OpenBSD 4.3-current (GENERIC.MP) #776: Sun Jun 29 11:34:39 MDT 2008 > > [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC.MP > > cpu0: Intel(R) Celeron(R) M processor 900MHz ("GenuineIntel" 686-class) 901 > > MHz > > cpu0: > > FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF > > real mem = 1064398848 (1015MB) > > avail mem = 1020956672 (973MB) > > mainbus0 at root > > bios0 at mainbus0: AT/286+ BIOS, date 05/12/08, BIOS32 rev. 0 @ > > 0xf0010, SMBIOS rev. 2.5 @ 0xf06f0 (37 entries) > > bios0: vendor American Megatrends Inc. version "0501" date 05/12/2008 > > bios0: ASUSTeK Computer INC. 900 > > apm0 at bios0: Power Management spec V1.2 > > apm0: AC on, battery charge unknown > > acpi at bios0 function 0x0 not configured > > pcibios0 at bios0: rev 3.0 @ 0xf0000/0x10000 > > pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf7410/176 (9 entries) > > pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82801FB LPC" rev 0x00) > > pcibios0: PCI bus #5 is the last bus > > bios0: ROM list: 0xc0000/0xf800! > > mainbus0: Intel MP Specification (Version 1.4) > > cpu0 at mainbus0: apid 0 (boot processor) > > cpu0: apic clock running at 100MHz > > mainbus0: bus 0 is type PCI > > mainbus0: bus 1 is type PCI > > mainbus0: bus 2 is type PCI > > mainbus0: bus 3 is type PCI > > mainbus0: bus 4 is type PCI > > mainbus0: bus 5 is type PCI > > mainbus0: bus 6 is type ISA > > ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 20, 24 pins > > pci0 at mainbus0 bus 0: configuration mode 1 (no bios) > > pchb0 at pci0 dev 0 function 0 "Intel 82915GM Host" rev 0x04 > > vga1 at pci0 dev 2 function 0 "Intel 82915GM Video" rev 0x04 > > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) > > wsdisplay0: screen 1-5 added (80x25, vt100 emulation) > > agp0 at vga1: aperture at 0xd0000000, size 0x10000000 > > "Intel 82915GM Video" rev 0x04 at pci0 dev 2 function 1 not configured > > azalia0 at pci0 dev 27 function 0 "Intel 82801FB HD Audio" rev 0x04: > > apic 1 int 16 (irq 5) > > azalia0: codec[s]: Realtek/0x0662 > > audio0 at azalia0 > > ppb0 at pci0 dev 28 function 0 "Intel 82801FB PCIE" rev 0x04: apic 1 > > int 16 (irq 5) > > pci_intr_map: bus 0 dev 28 func 0 pin 4; line 3 > > pci_intr_map: no MP mapping found > > pci1 at ppb0 bus 4 > > ppb1 at pci0 dev 28 function 1 "Intel 82801FB PCIE" rev 0x04: apic 1 > > int 17 (irq 11) > > pci_intr_map: bus 0 dev 28 func 1 pin 4; line 3 > > pci_intr_map: no MP mapping found > > pci2 at ppb1 bus 3 > > lii0 at pci2 dev 0 function 0 "Attansic Technology L2" rev 0xa0: apic > > 1 int 17 (irq 11), address 00:1f:c6:8f:0d:ee > > ukphy0 at lii0 phy 1: Generic IEEE 802.3u media interface, rev. 2: OUI > > 0x001374, model 0x0002 > > ppb2 at pci0 dev 28 function 2 "Intel 82801FB PCIE" rev 0x04: apic 1 > > int 18 (irq 10) > > pci_intr_map: bus 0 dev 28 func 2 pin 4; line 3 > > pci_intr_map: no MP mapping found > > pci3 at ppb2 bus 1 > > ath0 at pci3 dev 0 function 0 "Atheros AR5424" rev 0x01: apic 1 int 18 (irq > > 10) > > ath0: AR5424 14.2 phy 7.0 rf 0.0, WOR0W, address 00:15:af:a7:3d:55 > > uhci0 at pci0 dev 29 function 0 "Intel 82801FB USB" rev 0x04: apic 1 > > int 23 (irq 7) > > uhci1 at pci0 dev 29 function 1 "Intel 82801FB USB" rev 0x04: apic 1 > > int 19 (irq 3) > > uhci2 at pci0 dev 29 function 2 "Intel 82801FB USB" rev 0x04: apic 1 > > int 18 (irq 10) > > uhci3 at pci0 dev 29 function 3 "Intel 82801FB USB" rev 0x04: apic 1 > > int 16 (irq 5) > > ppb3 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xd4 > > pci_intr_map: bus 0 dev 30 func 0 pin 1; line 11 > > pci_intr_map: no MP mapping found > > pci_intr_map: bus 0 dev 30 func 0 pin 2; line 3 > > pci_intr_map: no MP mapping found > > pci4 at ppb3 bus 5 > > ichpcib0 at pci0 dev 31 function 0 "Intel 82801FBM LPC" rev 0x04: PM > > disabled > > pciide0 at pci0 dev 31 function 2 "Intel 82801FBM SATA" rev 0x04: DMA, > > channel 0 wired to compatibility, channel 1 wired to compatibility > > wd0 at pciide0 channel 1 drive 0: <ASUS-PHISON OB SSD> > > wd0: 1-sector PIO, LBA, 3847MB, 7880544 sectors > > wd1 at pciide0 channel 1 drive 1: <ASUS-PHISON SSD> > > wd1: 1-sector PIO, LBA, 7695MB, 15761088 sectors > > wd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 4 > > wd1(pciide0:1:1): using PIO mode 4, Ultra-DMA mode 4 > > ichiic0 at pci0 dev 31 function 3 "Intel 82801FB SMBus" rev 0x04: apic > > 1 int 19 (irq 0) > > iic0 at ichiic0 > > spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM non-parity PC2-3200CL5 SO-DIMM > > usb0 at uhci0: USB revision 1.0 > > uhub0 at usb0 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > > usb1 at uhci1: USB revision 1.0 > > uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > > usb2 at uhci2: USB revision 1.0 > > uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > > usb3 at uhci3: USB revision 1.0 > > uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > > isa0 at ichpcib0 > > isadma0 at isa0 > > pckbc0 at isa0 port 0x60/5 > > pckbd0 at pckbc0 (kbd slot) > > pckbc0: using irq 1 for kbd slot > > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > > pmsi0 at pckbc0 (aux slot) > > pckbc0: using irq 12 for aux slot > > wsmouse0 at pmsi0 mux 0 > > pcppi0 at isa0 port 0x61 > > midi0 at pcppi0: <PC speaker> > > spkr0 at pcppi0 > > npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 > > mtrr: Pentium Pro MTRR support > > umass0 at uhub1 port 2 configuration 1 interface 0 "SMI Corporation > > USB DISK" rev 2.00/11.00 addr 2 > > umass0: using SCSI over Bulk-Only > > scsibus0 at umass0: 2 targets, initiator 0 > > sd0 at scsibus0 targ 1 lun 0: <USB, Flash Disk, 1100> SCSI0 0/direct > > removable > > sd0: 956MB, 121 cyl, 255 head, 63 sec, 512 bytes/sec, 1957888 sec total > > umass1 at uhub2 port 1 configuration 1 interface 0 "ENE UB6225" rev > > 2.00/1.00 addr 2 > > umass1: using SCSI over Bulk-Only > > scsibus1 at umass1: 2 targets, initiator 0 > > sd1 at scsibus1 targ 1 lun 0: <USB2.0, CardReader SD0, 0100> SCSI0 > > 0/direct removable > > sd1: drive offline > > uvideo0 at uhub3 port 2 configuration 1 interface 0 "Chicony > > Electronics Co., Ltd. CNF7129" rev 2.00/15.12 addr 2 > > video0 at uvideo0 > > softraid0 at root > > root on sd0a swap on sd0b dump on sd0b > > This was just discussed: > http://marc.info/?l=openbsd-misc&m=121473630601623&w=2 > > -- > # Curt Micol