Laptop is a Toshiba L305-S5921. I'm running -current on it with a snapshot from
04/14/09. No, I couldn't wait for my new cd's
presently in route. ;) Mostly done just for learning purposes &
to see what I could get going on the new laptop which was given
to me as a present. I would've probably chosen a Lenovo if I'd
have had my choice, but I'm not going to turn down a free laptop.
Built GENERIC.MP which ran fine for me. When I do
sysctl hw.sensors
I get
hw.sensors.acpiac0.indicator0=On (power supply)
hw.sensors.acpibat0.volt0=12.34 VDC (voltage)
hw.sensors.acpibat0.volt1=12.34 VDC (current voltage)
hw.sensors.acpibat0.amphour0=4.50 Ah (last full capacity)
hw.sensors.acpibat0.amphour1=0.00 Ah (warning capacity)
hw.sensors.acpibat0.amphour2=0.00 Ah (low capacity)
hw.sensors.acpibat0.amphour3=4.50 Ah (remaining capacity), OK
hw.sensors.acpibat0.raw0=0 (battery full), OK
hw.sensors.acpibat0.raw1=0 (rate)
hw.sensors.cpu0.temp0=45.00 degC
which doesn't show cpu1. Next is the top portion of top's output
which does show both cpu's:
load averages: 1.09, 1.02, 0.99 01:03:49
22 processes: 21 idle, 1 on processor
CPU0 states: 3.7% user, 0.0% nice, 1.8% system, 0.3% interrupt, 94.2% idle
CPU1 states: 4.0% user, 0.0% nice, 1.8% system, 0.0% interrupt, 94.2% idle
Memory: Real: 7520K/349M act/tot Free: 2538M Swap: 0K/1028M used/tot
Here's dmesg which also shows both cpu's but fails on
acpitz0 at acpi0acpitz0: THRM: failed to read _TMP
which I thought might have something to do with the issue:
OpenBSD 4.5-current (GENERIC.MP) #1: Wed Apr 15 14:22:16 UTC 2009
r...@lapdaddy.cableone.net:/usr/src/sys/arch/i386/compile/GENERIC.MP
cpu0: Intel(R) Pentium(R) Dual CPU T3400 @ 2.16GHz ("GenuineIntel" 686-class)
2.17 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,EST,TM2,CX16,xTPR
real mem = 3081773056 (2939MB)
avail mem = 2983903232 (2845MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 12/23/08, SMBIOS rev. 2.4 @ 0xe8120 (35
entries)
bios0: vendor INSYDE version "1.60" date 12/23/2008
bios0: TOSHIBA Satellite L305
acpi0 at bios0: rev 2
acpi0: tables DSDT FACP HPET APIC MCFG ASF! SLIC BOOT SSDT
acpi0: wakeup devices LID0(S4) P32_(S0) UHC1(S3) UHC2(S3) ECHI(S3) EXP1(S0)
EXP2(S0) EXP3(S4) EXP4(S4) EXP5(S4) EXP6(S4) AZAL(S4)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpihpet0 at acpi0: 14318179 Hz
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: apic clock running at 166MHz
cpu1 at mainbus0: apid 1 (application processor)
cpu1: Intel(R) Pentium(R) Dual CPU T3400 @ 2.16GHz ("GenuineIntel" 686-class)
2.17 GHz
cpu1:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,EST,TM2,CX16,xTPR
ioapic0 at mainbus0: apid 4 pa 0xfec00000, version 20, 24 pins
ioapic0: misconfigured as apic 0, remapped to apid 4
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 4 (P32_)
acpiprt2 at acpi0: bus 2 (EXP1)
acpiprt3 at acpi0: bus 3 (EXP2)
acpiprt4 at acpi0: bus -1 (EXP3)
acpiprt5 at acpi0: bus -1 (EXP4)
acpiprt6 at acpi0: bus 6 (EXP5)
acpiprt7 at acpi0: bus -1 (EXP6)
acpiprt8 at acpi0: bus -1 (PEGP)
acpiec0 at acpi0
acpicpu0 at acpi0
acpicpu1 at acpi0
acpitz0 at acpi0acpitz0: THRM: failed to read _TMP
: failed to read _TMP
acpibtn0 at acpi0: PWRB
acpibtn1 at acpi0: LID0
acpiac0 at acpi0: AC unit online
acpibat0 at acpi0: BAT0 model "PA3534U-1BRS" serial 7C3B type Li-ion
acpivideo at acpi0 not configured
acpivideo at acpi0 not configured
bios0: ROM list: 0xc0000/0xfa00! 0xd0000/0x1000 0xd1000/0x2c00!
cpu0: unknown Enhanced SpeedStep CPU, msr 0x060f0d2a06000d2a
cpu0: using only highest and lowest power states
cpu0: Enhanced SpeedStep 2167 MHz (1372 mV): speeds: 2167, 1000 MHz
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel GM45 Host" rev 0x07
vga1 at pci0 dev 2 function 0 "Intel GM45 Video" rev 0x07
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
intagp0 at vga1
agp0 at intagp0: aperture at 0xc0000000, size 0x10000000
inteldrm0 at vga1: apic 4 int 16 (irq 11)
drm0 at inteldrm0
"Intel GM45 Video" rev 0x07 at pci0 dev 2 function 1 not configured
uhci0 at pci0 dev 26 function 0 "Intel 82801I USB" rev 0x03: apic 4 int 16 (irq
11)
uhci1 at pci0 dev 26 function 1 "Intel 82801I USB" rev 0x03: apic 4 int 21 (irq
10)
ehci0 at pci0 dev 26 function 7 "Intel 82801I USB" rev 0x03: apic 4 int 19 (irq
11)
ehci0: timed out waiting for BIOS
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
azalia0 at pci0 dev 27 function 0 "Intel 82801I HD Audio" rev 0x03: apic 4 int
22 (irq 11)
azalia0: codecs: Realtek ALC268, AT&T/Lucent/0x1040, using Realtek ALC268
audio0 at azalia0
ppb0 at pci0 dev 28 function 0 "Intel 82801I PCIE" rev 0x03: apic 4 int 17 (irq
5)
pci1 at ppb0 bus 2
re0 at pci1 dev 0 function 0 "Realtek 8101E" rev 0x02: RTL8102E (0x3480), apic
4 int 16 (irq 5), address 00:1e:33:9a:76:ee
rlphy0 at re0 phy 7: RTL8201L 10/100 PHY, rev. 1
ppb1 at pci0 dev 28 function 1 "Intel 82801I PCIE" rev 0x03: apic 4 int 16 (irq
11)
pci2 at ppb1 bus 3
ath0 at pci2 dev 0 function 0 "Atheros AR5424" rev 0x01: apic 4 int 17 (irq 11)
ath0: AR5424 14.2 phy 7.0 rf 0.0, WOR5_ETSIC, address 00:24:d2:01:89:ff
ppb2 at pci0 dev 28 function 4 "Intel 82801I PCIE" rev 0x03: apic 4 int 17 (irq
11)
pci3 at ppb2 bus 6
uhci2 at pci0 dev 29 function 0 "Intel 82801I USB" rev 0x03: apic 4 int 23 (irq
11)
uhci3 at pci0 dev 29 function 1 "Intel 82801I USB" rev 0x03: apic 4 int 19 (irq
11)
uhci4 at pci0 dev 29 function 2 "Intel 82801I USB" rev 0x03: apic 4 int 16 (irq
11)
uhci5 at pci0 dev 29 function 3 "Intel 82801I USB" rev 0x03: apic 4 int 18 (irq
11)
ehci1 at pci0 dev 29 function 7 "Intel 82801I USB" rev 0x03: apic 4 int 23 (irq
11)
ehci1: timed out waiting for BIOS
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb3 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0x93
pci4 at ppb3 bus 4
pcib0 at pci0 dev 31 function 0 vendor "Intel", unknown product 0x2919 rev 0x03
ahci0 at pci0 dev 31 function 2 "Intel 82801I AHCI" rev 0x03: apic 4 int 19
(irq 11), AHCI 1.2
ahci0: PHY offline on port 1
ahci0: PHY offline on port 4
scsibus0 at ahci0: 32 targets
sd0 at scsibus0 targ 0 lun 0: <ATA, ST9250827AS, 3.AA> SCSI3 0/direct fixed
sd0: 238475MB, 512 bytes/sec, 488397168 sec total
cd0 at scsibus0 targ 5 lun 0: <MATSHITA, DVD-RAM UJ880AS, 1.50> ATAPI 5/cdrom
removable
ichiic0 at pci0 dev 31 function 3 "Intel 82801I SMBus" rev 0x03: apic 4 int 18
(irq 11)
iic0 at ichiic0
spdmem0 at iic0 addr 0x50: 2GB DDR2 SDRAM non-parity PC2-6400CL5 SO-DIMM
spdmem1 at iic0 addr 0x52: 2GB DDR2 SDRAM non-parity PC2-6400CL5 SO-DIMM
usb2 at uhci0: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci1: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci2: USB revision 1.0
uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb5 at uhci3: USB revision 1.0
uhub5 at usb5 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb6 at uhci4: USB revision 1.0
uhub6 at usb6 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb7 at uhci5: USB revision 1.0
uhub7 at usb7 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
mtrr: Pentium Pro MTRR support
umass0 at uhub0 port 4 configuration 1 interface 0 "Generic USB2.0-CRW" rev
2.00/58.87 addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <Generic-, Multi-Card, 1.00> SCSI0 0/direct
removable
sd1: drive offline
uhidev0 at uhub4 port 1 configuration 1 interface 0 "vendor 0x15d9 USB Mouse"
rev 1.10/1.00 addr 2
uhidev0: iclass 3/1
ums0 at uhidev0: 3 buttons, Z dir
wsmouse1 at ums0 mux 0
softraid0 at root
root on sd0a swap on sd0b dump on sd0b
pckbc: command timeout
pms_disable: command error
Not being able to read cpu1 temp probably isn't a big deal, at
least I'm guessing it's not & that's it probably pretty close
to the same temp as cpu0 since they both seem to share the load
fairly equally when I'm doing intensive stuff like building a
kernel & so forth. I just wanted to try to learn how to enable
all functions on cpu1 if possible. Also, I thought it might help
if I included the advanced cmos settings:
Core Multi-Processing: [Enabled]
Dynamic CPU Frequency Mode: [Dynamic]
(other choice on above setting is 'Always Low')
Pointing Devices: [Disabled]
(above disables touchpad which I hate. using usb mouse instead)
Built-in LAN: [Enabled]
Wake-up on LAN: [Disabled]
Wake On Wireless LAN: [Disabled]
Critical Battery Wake-up: [Enabled]
Execute-Disable Bit Capability: [Enabled]
Intel Virtualization Technology: [Disabled]
Intel (R) Turbo Memory: [Enabled]
Legacy USB Support: [Enabled]
Wake on Keyboard: [Disabled]
Intel Dynamic Acceleration: [Disabled]
(not able to change above setting)
SATA Controller Mode: [AHCI]
Any help, tips, reading links, etc., greatly appreciated.
Denny White
--
===============================================================
() ASCII ribbon campaign - against html e-mail
/\ www.asciiribbon.org - against proprietary attachments
===============================================================
GnuPG key : 0x1644E79A | http://wwwkeys.nl.pgp.net
Fingerprint: D0A9 AD44 1F10 E09E 0E67 EC25 CB44 F2E5 1644 E79A
===============================================================
