That's a lot of dump.
So, the fact that there is only loopback and your eth0 (hardwired
connection) is disappointing. You don't have your wifi card driver
loaded.
The dmesg|grep eth is not worth much. On a fresh boot, you can run dmesg
bootmsg.txt and see what is going on there, but we probably don't need
to do that. It's informative to see what's going on at boot time, but
more for you to learn what is going on.
For a wifi device, iwconfig has largely replaced ifconfig on linux for
anything to do with wifi stuff. You'll need the device listed in ifconfig
though.
Someone correct me if I'm wrong but intel pro1000e is the ethernet NIC
right? Denis: you'll have to lspci | less and run through what's there,
there should be something about the broadcom wifi (or any wifi something).
Then re-run with -v and look at that entry and see what there is, -k will
tell you what kernel modules go with it, but you're going to have to
modprobe the right driver based on what you get out of the lspci dump. Ie
lspci->get card / chipset info -> google for driver -> modprobe the driver
-> success. In any case, once you're sure about the chipset you can
google your distro and see what problems/solutions there are.
You also might want to verify that there are some power lights or some
kind of 'yes I'm not a fried /dead card' signals.. I guess if it "worked
under windows" then that's verification enough.
Good luck, report back success/problems.
On Tue, 28 Feb 2012, Denis-André Desjardins. wrote:
The requested information;
ifconfig
eth0 Link encap:Ethernet HWaddr 00:15:60:4e:d5:59
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:17
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:140 errors:0 dropped:0 overruns:0 frame:0
TX packets:140 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:10896 (10.8 KB) TX bytes:10896 (10.8 KB)
dmesg|grep eth
[ 0.156606] HP Compaq Laptop series board detected. Selecting BIOS-method
for reboots.
[ 0.392495] ACPI Error: Method parse/execution failed [\_SB_.PCI0._OSC]
(Node f40255e8), AE_ALREADY_EXISTS (20110112/psparse-536)
[ 0.392512] ACPI: Marking method _OSC as Serialized because of
AE_ALREADY_EXISTS error
[ 0.396728] ACPI Error: Method parse/execution failed [\_SB_.PCI0._OSC]
(Node f40255e8), AE_ALREADY_EXISTS (20110112/psparse-536)
[ 0.396895] ACPI Error: Method parse/execution failed [\_SB_.PCI0._OSC]
(Node f40255e8), AE_ALREADY_EXISTS (20110112/psparse-536)
[ 0.955212] i2c-core: driver [adp5520] using legacy suspend method
[ 0.955215] i2c-core: driver [adp5520] using legacy resume method
[ 1.630847] tg3 0000:3f:00.0: eth0: Tigon3 [partno(BCM95752) rev 6001]
(PCI Express) MAC address 00:15:60:4e:d5:59
[ 1.630858] tg3 0000:3f:00.0: eth0: attached PHY is 5752
(10/100/1000Base-T Ethernet) (WireSpeed[1])
[ 1.630865] tg3 0000:3f:00.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0]
ASF[0] TSOcap[1]
[ 1.630871] tg3 0000:3f:00.0: eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 8.884616] ADDRCONF(NETDEV_UP): eth0: link is not ready
lspci|grep -i eth
3f:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5752 Gigabit
Ethernet PCI Express (rev 01)
rfkill list
0: phy1: Wireless LAN
Soft blocked: no
Hard blocked: no
tail dmesg
[ 9.305216] lp0: using parport0 (interrupt-driven).
[ 9.308249] type=1400 audit(1330459696.648:11): apparmor="STATUS"
operation="profile_load" name="/usr/bin/evince-previewer" pid=624
comm="apparmor_parser"
[ 9.337830] psmouse serio1: ID: 10 00 64
[ 9.380396] input: Chicony Compaq Internet Keyboard as
/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1:1.0/input/input2
[ 9.380784] generic-usb 0003:049F:000E.0001: input,hidraw0: USB HID v1.10
Keyboard [Chicony Compaq Internet Keyboard] on usb-0000:00:1d.0-1/input0
[ 9.400844] logips2pp: Detected unknown logitech mouse model 105
[ 9.558442] input: Chicony Compaq Internet Keyboard as
/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1:1.1/input/input3
[ 9.558958] generic-usb 0003:049F:000E.0002: input,hiddev0,hidraw1: USB
HID v1.10 Device [Chicony Compaq Internet Keyboard] on
usb-0000:00:1d.0-1/input1
[ 9.559045] usbcore: registered new interface driver usbhid
[ 9.559048] usbhid: USB HID core driver
_______________________________________________
mlug mailing list
[email protected]
https://listes.koumbit.net/cgi-bin/mailman/listinfo/mlug-listserv.mlug.ca
