Today you sent me mail regarding Re: [rrd-developers] Preliminary libtooled...:
*> Tobias, *> *> Could you push out a rrdtool 1.0.5 with the libtool changes I added *> to 1.0.3 and with the differences you put in between 1.0.3 and *> 1.0.4? This will make it easier to work on supplying patches to *> a common code base, instead of patches for the libtool 1.0.3 or *> 1.0.4. *> *> To get the new automake/libtool system build static by default *> and make shared optionally, replace the following line *> *> AC_DISABLE_STATIC *> *> with *> *> AC_DISABLE_SHARED *> *> in configure.in. To have both static and shared, remove the *> AC_DISABLE_STATIC completely. *> *> However, I think that if the user will be building the perl RRDs.so *> module, then shared building should be enabled in addition to a *> static library. If not, then build only a static module. You don't *> want users to have to specify a shared library if they are going *> to compile RRDs.so. I will try to add 1.0.3b to 1.0.4 on monday ... I wont be at work over the weekend ... :-) in any event ... thanks verymuch for your effort ... cheers tobi *> *> Have a great weekend, *> Blair *> *> Tobias Oetiker wrote: *> *> > I just did some further test on rrdtool libtool .... and found that I can *> > not yet include it into the main edition, for the reasons listed below ... I *> > will release 1.0.4 in a few minutes, with all the updates I made since 1.0.3 *> > so that any libtool gurus out there can have a shot at it ... *> > *> > I will not be makeing many changes to rrdtool in the comming weeks as I am *> > working on MRTG-3 ... so this is the ideal time to add proper libtool *> > support ... with dist, install and all ... *> > *> > Just one thing: *> > *> > * I would prefere if building static libraries remained the default *> > *> > building rrdtool with a dynamic lib should be enabled with ./configure *> > --with-shared=yes or the like ... *> > *> > cheers *> > tobi *> > *> > *> *> > *> 1) Made sure all the RRdtool pieces get installed in the correct place *> > *> with a make install. *> > *> 2) Added all files to the Makefile.am's such that a make dist can *> > *> be performed to create a RRDtool distribution. *> > *> 3) docs/Makefile has not been touched. This could also probably be *> > *> automake'd. *> > *> 4) I have not figured out how to put perl-shared and perl-piped *> > *> inside the automake structure nicely, but it works. Look at the *> > *> top level Makefile.am to see how I do it. *> > *> *> > *> Since this work has a lot of changes, I'm just leaving the new tar file *> > *> up at *> > *> *> > *> ftp://ftp.gps.caltech.edu/pub/blair/rrdtool-1.0.3a.tar.gz *> > *> *> > *> The diffs between this and pure 1.0.3 are 165 k in size. *> > *> *> > *> If you do any developing on this, please make sure to download and *> > *> install the latest autoconf (2.13), automake (1.4), and libtool *> > *> (1.3.3) from ftp.gnu.org. *> > *> *> > *> Good luck, *> > *> Blair *> > *> > -- *> > ______ __ _ *> > /_ __/_ / / (_) Oetiker, Timelord & SysMgr @ EE-Dept ETH-Zurich *> > / // _ \/ _ \/ / TEL: +41(0)1-6325286 FAX:...1517 ICQ: 10419518 *> > /_/ \.__/_.__/_/ [EMAIL PROTECTED] http://ee-staff.ethz.ch/~oetiker *> -- ______ __ _ /_ __/_ / / (_) Oetiker, Timelord & SysMgr @ EE-Dept ETH-Zurich / // _ \/ _ \/ / TEL: +41(0)1-6325286 FAX:...1517 ICQ: 10419518 /_/ \.__/_.__/_/ [EMAIL PROTECTED] http://ee-staff.ethz.ch/~oetiker -- Binary/unsupported file stripped by Listar -- -- Type: TEXT/X-VCARD -- File: bzajac.vcf -- Desc: Card for Dr. Blair Zajac -- * To unsubscribe from the rrd-developers mailing list, send a message with the subject: unsubscribe to [EMAIL PROTECTED]
