I've searched the archvies and the forums at http://forums.gentoo.org and I'm having a hell of time getting the Gray remote that came with my PVR-250 working.
I followed the instructions here: http://gentoo-wiki.com/HARDWARE_Setup_MythTV When I do a make menuconfig I do not have any option to enable Linux Infrared controller. lircd is using /dev/lirc/0. If I cat /dev/lirc/0 and press buttons on the remote I get output on the screen (a bunch of garbage, but output none the less). irw doesn't seem to do anything my /etc/lircd.conf: begin remote name Hauppauge bits 13 flags SHIFT_ENC eps 30 aeps 100 one 950 830 zero 950 830 plead 960 gap 89584 repeat_bit 2 begin codes TV 0x000000000000100F RADIO 0x000000000000100C FULL_SCREEN 0x000000000000102E CH+ 0x0000000000001020 CH- 0x0000000000001021 VOL- 0x0000000000001011 VOL+ 0x0000000000001010 MUTE 0x000000000000100D SOURCE 0x0000000000001022 1 0x0000000000001001 2 0x0000000000001002 3 0x0000000000001003 4 0x0000000000001004 5 0x0000000000001005 6 0x0000000000001006 7 0x0000000000001007 8 0x0000000000001008 9 0x0000000000001009 0 0x0000000000001000 RESERVED 0x000000000000101E MINIMIZE 0x0000000000001026 end codes end remote begin remote name hauppauge_pvr bits 13 flags RC5|CONST_LENGTH eps 30 aeps 100 one 969 811 zero 969 811 plead 1097 gap 114605 toggle_bit 2 begin codes Power 0x00000000000017FD Go 0x00000000000017FB 1 0x00000000000017C1 2 0x00000000000017C2 3 0x00000000000017C3 4 0x00000000000017C4 5 0x00000000000017C5 6 0x00000000000017C6 7 0x00000000000017C7 8 0x00000000000017C8 9 0x00000000000017C9 Back/Exit 0x00000000000017DF 0 0x00000000000017C0 Menu 0x00000000000017CD Red 0x00000000000017CB Green 0x00000000000017EE Yellow 0x00000000000017F8 Blue 0x00000000000017E9 Ch+ 0x00000000000017E0 Ch- 0x00000000000017E1 Vol- 0x00000000000017D1 Vol+ 0x00000000000017D0 Ok 0x00000000000017E5 Mute 0x00000000000017CF Blank 0x00000000000017CC Full 0x00000000000017FC Rewind 0x00000000000017F2 Play 0x00000000000017F5 Forward 0x00000000000017F4 Record 0x00000000000017F7 Stop 0x00000000000017F6 Pause 0x00000000000017F0 Replay 0x00000000000017E4 Skip 0x00000000000017DE end codes end remote I've tried running mythfrontend as root and a normal user. my lircrc: begin prog = irxevent button = OK repeat = 3 config = Key M CurrentWindow end begin prog = irxevent button = CH+ repeat = 3 config = Key Up CurrentWindow end begin prog = irxevent button = CH- repeat = 3 config = Key Down CurrentWindow end begin prog = irxevent button = MENU repeat = 3 config = Key Return CurrentWindow end begin prog = irxevent button = RECORD repeat = 3 config = Key Return CurrentWindow end begin prog = irxevent button = RED repeat = 3 config = Key X CurrentWindow end begin prog = irxevent button = GREEN repeat = 3 config = Key I CurrentWindow end begin prog = irxevent button = YELLOW repeat = 3 config = Key bracketleft CurrentWindow end begin prog = irxevent button = BLUE repeat = 3 config = Key bracketright CurrentWindow end begin prog = irxevent button = BLANK repeat = 3 config = Key D CurrentWindow end begin prog = irxevent button = VOL- repeat = 3 config = Key Left CurrentWindow end begin prog = irxevent button = REV repeat = 3 config = Key Left CurrentWindow end begin prog = irxevent button = PLAY repeat = 3 config = Key P CurrentWindow end begin prog = irxevent button = MUTE repeat = 3 config = Key backslash CurrentWindow end begin prog = irxevent button = VOL+ repeat = 3 config = Key Right CurrentWindow end begin prog = irxevent button = FFW repeat = 3 config = Key Right CurrentWindow end begin prog = irxevent button = BACK/EXIT repeat = 3 config = Key Escape CurrentWindow end begin prog = irxevent button = FULL repeat = 3 config = Key Escape CurrentWindow end begin prog = irxevent button = PAUSE repeat = 3 config = Key P CurrentWindow end begin prog = irxevent button = 0 config = Key 0 CurrentWindow end begin prog = irxevent button = 1 config = Key 1 CurrentWindow end begin prog = irxevent button = 2 config = Key 2 CurrentWindow end begin prog = irxevent button = 3 config = Key 3 CurrentWindow end begin prog = irxevent button = 4 config = Key 4 CurrentWindow end begin prog = irxevent button = 5 config = Key 5 CurrentWindow end begin prog = irxevent button = 6 config = Key 6 CurrentWindow end begin prog = irxevent button = 7 config = Key 7 CurrentWindow end begin prog = irxevent button = 8 config = Key 8 CurrentWindow end begin prog = irxevent button = 9 config = Key 9 CurrentWindow end I had to place the lircrc file as ~/.lircrc for irxevent to be able to find in. In my logs I can see where lircd accepts the new client and then disconnects it when I close mythfrontend but the remote doesn't work at all in myth. Any ideas? --Dennis
_______________________________________________ mythtv-users mailing list [email protected] http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
