maybe better in mythtvsetup to set the options on the hd3000 dvb to record in ts mode instead of ps mode. i did this and it seems to be working ok. going to test out a recording, as I really don't plan on watching livetv with this setup, so we'll have to see how it works out. -AG
On Thu, 31 Mar 2005 20:55:43 -0500, Marc Tousignant <[EMAIL PROTECTED]> wrote: > >Have you been able to successfully tune the frequencies using azap? (get > >the instructions for installing it here: > >http://www.rsmas.miami.edu/personal/angel/mythtv/air2pc-howto.html) > > > >You might try just getting your card to successfully tune the channels, > >and as a worst case scenario, use the frequencies reported by azap for > >your channels in the DVB Transports section of the MythTV configuration. > > > >But first, just to rule out problems with your driver setup, you need to > >make sure azap works. > > John > > Azap works to tune channels and Dvbscan confirms there are subchannels > > yggdrasil root # azap -c /root/channels.conf-qam-correct -r c82 > using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' > tuning to 573000000 Hz > video pid 0x0000, audio pid 0x0000 > status 1f | signal 0977 | snr fded | ber 00000000 | unc 00000000 | > FE_HAS_LOCK > status 1f | signal 0977 | snr fdd5 | ber 00000000 | unc 00000000 | > FE_HAS_LOCK > status 1f | signal 0977 | snr fded | ber 00000000 | unc 00000000 | > FE_HAS_LOCK > > yggdrasil root # dvbscan -cvvv > using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' > parse_section:981: pid 0x00 tid 0x00 table_id_ext 0x80b6, 0/0 (version 2) > PAT > parse_section:981: pid 0x30 tid 0x02 table_id_ext 0x0001, 0/0 (version 4) > PMT 0x0030 for service 0x0001 > VIDEO : PID 0x0800 > OTHER : PID 0x0801 TYPE 0x81 > OTHER : PID 0x0802 TYPE 0x81 > parse_pmt:798: 0x0000 0x0001: (null) -- (null), pmt_pid 0x0030, vpid 0x0800, > apid 0x0000 () > parse_section:981: pid 0x31 tid 0x02 table_id_ext 0x0002, 0/0 (version 26) > PMT 0x0031 for service 0x0002 > VIDEO : PID 0x0840 > OTHER : PID 0x0841 TYPE 0x81 > parse_pmt:798: 0x0000 0x0002: (null) -- (null), pmt_pid 0x0031, vpid 0x0840, > apid 0x0000 () > WARNING: filter timeout pid 0x0011 > dumping lists (2 services) > [0001] (0x0001) 00: PCR == V V 0x0800 > [0002] (0x0002) 00: PCR == V V 0x0840 > Done. > > Dvbstream broadcasts the TS over the network so I can watch it live with > VideoLAN > yggdrasil root # ./dvbstream/dvbstream -v -qam 256 -f 573000000 -c 0 8192 > dvbstream v0.6 - (C) Dave Chapman 2001-2004 > Released under the GPL. > Latest version available from http://www.linuxstb.org/ > Tuning to 573000000 Hz > Using DVB card "pcHDTV HD3000 HDTV", freq=573000000 > tuning ATSC to 573000000, modulation=5 > Getting frontend status > Bit error rate: 0 > Signal strength: 916 > SNR: 64981 > UNC: 0 > FE_STATUS: FE_HAS_SIGNAL FE_HAS_LOCK FE_HAS_CARRIER FE_HAS_VITERBI > FE_HAS_SYNC > dvbstream will stop after -1 seconds (71582788 minutes) > Using 224.0.1.2:5004:2 > version=2 > Streaming 1 stream > > >AACK! > > > >You shouldn't have to do this! Please make sure your card is configured > >correctly.. (see my previous post) Channel scanning should work just > >fine, and put all of the appropriate entries in your channels lineup. If > >it doesn't, something else is probably wrong. > > It's the only way I can get myth to agree with me that there is something > coming in on my card. > The channel scan myth performs locks on all the right channels but reports > timed out while tuning. > > You got any better ideas I'm open to trying. > > Got home and tried the channel I setup. It plays.. Kinda.. it's almost as if > something within mythtv itself is interfering with the signal or hampering > playback. I get massive pixelization and the audio skips so much you can't > hear anything understandable. > > Feeding from dvbstream to videolan works flawlessly through my network. > Both my myth system (yggdrasil) and my gaming system (nidheg) are P4 > 3.40GHz's with GeForce FX 5700LE's > The key differences between them are; nidheg has an audigy card and 1 gig > ram and yggdrasil has the capture cards, PVR-350 and HD3000, and 512 meg > ram. > Ya overkill but yggdrasil is intended to be front/back and a transcoder with > all intentions of lasting a long time. > > Marc > > > _______________________________________________ > mythtv-users mailing list > [email protected] > http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users > > > _______________________________________________ mythtv-users mailing list [email protected] http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
