John Harvey wrote:
Can you mail me the section from the messages file
about updating registers and adjusting width/height.
Should be at the end of the file after you run
mplayer.
Also the output of mplayer would be useful.
Thanks
John
sigh.. Well, since that last mail, something broke. After rebooting just
now, I'm back to a non moving green and purple screen :(
The only things I was changing were mplayer settings, and they have all
been changed back again. So I have no idea what's changed..
As for the logs, they are all attached
thanks
Dunc
Jun 17 19:18:33 Gobbla kernel: ivtv: ==================== START INIT IVTV
====================
Jun 17 19:18:33 Gobbla kernel: ivtv: version 0.3.6 (n) loading
Jun 17 19:18:33 Gobbla kernel: ivtv: Linux version: 2.6.11-1.27_FC3 686 REGPARM
4KSTACKS gcc-3.4
Jun 17 19:18:33 Gobbla kernel: ivtv: In case of problems please include the
debug info
Jun 17 19:18:33 Gobbla kernel: ivtv: between the START INIT IVTV and END INIT
IVTV lines when
Jun 17 19:18:33 Gobbla kernel: ivtv: mailing the ivtv-devel mailinglist.
Jun 17 19:18:33 Gobbla kernel: ivtv: Autodetected WinTV PVR 350 card
Jun 17 19:18:33 Gobbla kernel: ivtv: Found an iTVC15 based chip
Jun 17 19:18:33 Gobbla kernel: ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
Jun 17 19:18:33 Gobbla kernel: PCI: setting IRQ 10 as level-triggered
Jun 17 19:18:33 Gobbla kernel: ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 10
(level, low) -> IRQ 10
Jun 17 19:18:33 Gobbla kernel: ivtv: Unreasonably low latency timer, setting to
64 (was 32)
Jun 17 19:18:33 Gobbla kernel: ivtv: VIA PCI device: 0x3099 vendor: 0x1106
Jun 17 19:18:33 Gobbla kernel: tveeprom: Hauppauge: model = 48139, rev = K257,
serial# = 2962861
Jun 17 19:18:33 Gobbla kernel: tveeprom: tuner = Philips FM1216 ME MK3 (idx =
57, type = 38)
Jun 17 19:18:33 Gobbla kernel: tveeprom: tuner fmt = PAL(B/G) PAL(I) SECAM(L/L)
PAL(D/K) (eeprom = 0x74, v4l2 = 0x00400e17)
Jun 17 19:18:33 Gobbla kernel: tveeprom: audio_processor = CS5331 (type = 9)
Jun 17 19:18:33 Gobbla kernel: ivtv: i2c attach [client=tveeprom[50],ok]
Jun 17 19:18:33 Gobbla kernel: ivtv: Tuner Type 38, Tuner formats 0x00400e17,
Radio: yes, Model 0x00ad2557, Revision 0x00000001
Jun 17 19:18:33 Gobbla kernel: ivtv: Radio detected
Jun 17 19:18:33 Gobbla kernel: tuner: Ignoring new-style parameters in presence
of obsolete ones
Jun 17 19:18:33 Gobbla kernel: tuner: chip found at addr 0xc2 i2c-bus ivtv i2c
driver #0
Jun 17 19:18:33 Gobbla kernel: ivtv: i2c attach [client=(tuner unset),ok]
Jun 17 19:18:33 Gobbla kernel: saa7115: starting probe for adapter ivtv i2c
driver #0 (0x10005)
Jun 17 19:18:33 Gobbla kernel: saa7115: detecting saa7115 client on address 0x42
Jun 17 19:18:33 Gobbla kernel: saa7115: writing init values
Jun 17 19:18:33 Gobbla kernel: ivtv: i2c attach [client=saa7115[50],ok]
Jun 17 19:18:33 Gobbla kernel: saa7115: status: (1E) 0x00, (1F) 0xc0
Jun 17 19:18:33 Gobbla kernel: saa7127: Ignoring new-style parameters in
presence of obsolete ones
Jun 17 19:18:33 Gobbla kernel: saa7127: video encoder driver version V 0.3
loaded
Jun 17 19:18:33 Gobbla kernel: saa7127: detecting saa7127 client on address 0x88
Jun 17 19:18:33 Gobbla kernel: saa7127: Selecting NTSC video Standard
Jun 17 19:18:33 Gobbla kernel: saa7127: Selecting S-Video+Composite
Jun 17 19:18:33 Gobbla kernel: saa7127: Turn WSS off
Jun 17 19:18:33 Gobbla kernel: saa7127: Widescreen Mode 4:3 Full Format
Jun 17 19:18:33 Gobbla kernel: saa7127: Selecting Normal Encoder Input
Jun 17 19:18:33 Gobbla kernel: saa7127: Enable Video Output
Jun 17 19:18:33 Gobbla kernel: ivtv: i2c attach [client=saa7127[50],ok]
Jun 17 19:18:33 Gobbla rpcidmapd: rpc.idmapd startup succeeded
Jun 17 19:18:33 Gobbla kernel: msp34xx: ivtv version
Jun 17 19:18:33 Gobbla kernel: msp34xx: init: chip=MSP3418W-B3, has NICAM
support, simple (D) mode, simpler (G) no-thread mode
Jun 17 19:18:33 Gobbla kernel: msp34xx: $Id$ compiled on: Jun 17 2005 16:21:07
Jun 17 19:18:33 Gobbla kernel: ivtv: i2c attach [client=MSP3418W-B3,ok]
Jun 17 19:18:33 Gobbla kernel: tda9885/6/7: chip found @ 0x86
Jun 17 19:18:33 Gobbla kernel: ivtv: i2c attach [client=tda9887,ok]
Jun 17 19:18:33 Gobbla kernel: ivtv: Encoder revision: 0x02040024
Jun 17 19:18:33 Gobbla kernel: ivtv: Encoder Firmware may be buggy, use version
0x02040011
Jun 17 19:18:33 Gobbla kernel: ivtv: Decoder revision: 0x02020023
Jun 17 19:18:33 Gobbla kernel: ivtv: Configuring WinTV PVR 350 card with 10
streams
Jun 17 19:18:33 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 0 minor 0
Jun 17 19:18:33 Gobbla kernel: ivtv: Create DMA stream 0 using 64 32768 byte
buffers 0 kbytes total
Jun 17 19:18:33 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 1 minor
32
Jun 17 19:18:33 Gobbla kernel: ivtv: Create DMA stream 1 using 161 12960 byte
buffers 0 kbytes total
Jun 17 19:18:33 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 2 minor
224
Jun 17 19:18:33 Gobbla kernel: ivtv: Create DMA stream 2 using 165 12635 byte
buffers 0 kbytes total
Jun 17 19:18:33 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 3 minor
24
Jun 17 19:18:33 Gobbla kernel: ivtv: Create DMA stream 3 using 455 4608 byte
buffers 0 kbytes total
Jun 17 19:18:33 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 4 minor
64
Jun 17 19:18:33 Gobbla kernel: ivtv: Create stream 4
Jun 17 19:18:33 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 5 minor
16
Jun 17 19:18:33 Gobbla kernel: ivtv: Create DMA stream 5 using 16 65536 byte
buffers 0 kbytes total
Jun 17 19:18:33 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 6 minor
228
Jun 17 19:18:33 Gobbla kernel: ivtv: Create DMA stream 6 using 1024 2048 byte
buffers 0 kbytes total
Jun 17 19:18:33 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 7 minor
232
Jun 17 19:18:33 Gobbla kernel: ivtv: Create stream 7
Jun 17 19:18:33 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 8 minor
48
Jun 17 19:18:33 Gobbla kernel: ivtv: Create DMA stream 8 using 20 51840 byte
buffers 0 kbytes total
Jun 17 19:18:33 Gobbla kernel: ivtv: Create DMA stream 9 using 32 65536 byte
buffers 0 kbytes total
Jun 17 19:18:33 Gobbla kernel: ivtv: Setting Tuner 38
Jun 17 19:18:33 Gobbla kernel: tuner: type set to 38 (Philips PAL/SECAM multi
(FM1216ME MK3)) by ivtv i2c driver #0
Jun 17 19:18:33 Gobbla kernel: saa7115: decoder set norm PAL
Jun 17 19:18:33 Gobbla kernel: saa7115: set audio: 0x01
Jun 17 19:18:33 Gobbla kernel: saa7115: decoder set input (4)
Jun 17 19:18:33 Gobbla kernel: saa7115: now setting Composite input
Jun 17 19:18:33 Gobbla kernel: ivtv: Setting audio matrix to input 3, output 1
Jun 17 19:18:33 Gobbla kernel: ivtv: Switching standard to PAL.
Jun 17 19:18:33 Gobbla kernel: ivtv: ivtv_enc_thread: pid = 2025, itv =
0xe0e18720
Jun 17 19:18:33 Gobbla kernel: ivtv: ivtv_enc_vbi_thread: pid = 2026, itv =
0xe0e18720
Jun 17 19:18:33 Gobbla kernel: ivtv: ivtv_dec_thread: pid = 2027, itv =
0xe0e18720
Jun 17 19:18:33 Gobbla kernel: ivtv: ivtv_dec_vbi_thread: pid = 2028, itv =
0xe0e18720
Jun 17 19:18:33 Gobbla kernel: saa7115: decoder set norm PAL
Jun 17 19:18:33 Gobbla kernel: saa7115: set audio: 0x01
Jun 17 19:18:33 Gobbla kernel: saa7127: Setting Encoder Video Standard
Jun 17 19:18:33 Gobbla kernel: saa7127: Set PAL Video Mode
Jun 17 19:18:33 Gobbla kernel: saa7127: Selecting PAL video Standard
Jun 17 19:18:33 Gobbla kernel: ivtv: Initialized WinTV PVR 350, card #0
Jun 17 19:18:33 Gobbla kernel: ivtv: ==================== END INIT IVTV
====================
Jun 17 19:20:37 Gobbla kernel: ivtv: Tried to open YUV output device but need
to send data to mpeg decoder before it can be used
Jun 17 19:20:38 Gobbla kernel: ivtv: Allocate DMA stream 8 using 20 51840 byte
buffers 1048576 kbytes total
Jun 17 19:20:38 Gobbla kernel: ivtv-osd: Need to adjust width to src_w 512
dst_w 720 scaled_w 512
Jun 17 19:20:38 Gobbla kernel: ivtv: Update reg 0x2834 02d002d0->02d00200
0x2838 02d002d0->02d00200
Jun 17 19:20:38 Gobbla kernel: ivtv: Update reg 0x283c 00080000->0005b05c
0x2844 00080000->0005b05c
Jun 17 19:20:38 Gobbla kernel: ivtv: Update reg 0x2854 00200000->0016c190
Jun 17 19:20:38 Gobbla kernel: ivtv: Update reg 0x285c 00100000->000b60b8
0x2864 00100000->000b60b8
Jun 17 19:20:38 Gobbla kernel: ivtv-osd: Need to adjust heighth to src_h 288
dst_h 432 scaled_h 384
Jun 17 19:20:38 Gobbla kernel: ivtv: Update reg 0x2930 001aaaab->00155500
0x2938 001aaaab->00155500
Jun 17 19:20:38 Gobbla kernel: ivtv: Update reg 0x2928 00035555->0002aaa0
0x292c 00035a69->0002afb4
Jun 17 19:20:38 Gobbla kernel: ivtv: Update reg 0x2920 0006aaab->00055540
0x2924 0006afbf->00055a54
Jun 17 19:20:38 Gobbla kernel: ivtv: Update reg 0x2918 024001e0->02400180
0x291c 024000f0->024000c0
Jun 17 19:20:38 Gobbla kernel: ivtv: Update reg 0x2940 000d5555->000aaa80
0x2948 000d5555->000aaa80
Jun 17 19:20:38 Gobbla kernel: ivtv: Update reg 0x2960 00ef01df->00bf017f
MPlayer 1.0pre7-3.4.3 (C) 2000-2005 MPlayer Team
CPU: Advanced Micro Devices Athlon MP/XP Thoroughbred (Family: 6,
Stepping: 1)
Detected cache-line size is 64 bytes
CPUflags: MMX: 1 MMX2: 1 3DNow: 1 3DNow2: 1 SSE: 1 SSE2: 0
Linux RTC init error in ioctl (rtc_irqp_set 1024): Permission denied
Try adding "echo 1024 > /proc/sys/dev/rtc/max-user-freq" to your system
startupscripts.
Setting up LIRC support...
Playing Scratch (Hip-hop documentary).avi.
AVI file format detected.
VIDEO: [DIV3] 512x288 24bpp 25.000 fps 966.7 kbps (118.0 kbyte/s)
Clip info:
Software: Nandub v1.0rc2
==========================================================================
Opening audio decoder: [mp3lib] MPEG layer-2, layer-3
AUDIO: 44100 Hz, 2 ch, s16le, 128.0 kbit/9.07% (ratio: 16000->176400)
Selected audio codec: [mp3] afm:mp3lib (mp3lib MPEG layer-2, layer-3)
==========================================================================
vo: X11 running at 720x576 with depth 24 and 32 bpp (":0.0" => local
display)
==========================================================================
Opening video decoder: [ffmpeg] FFmpeg's libavcodec codec family
Selected video codec: [ffdivx] vfm:ffmpeg (FFmpeg DivX ;-) (MS MPEG-4
v3))
==========================================================================
Checking audio filter chain for 44100Hz/2ch/s16le ->
44100Hz/2ch/s16le...
AF_pre: 44100Hz/2ch/s16le
alsa-init: 1 soundcard found, using: default
alsa: 44100 Hz/2 channels/4 bpf/60208 bytes buffer/Signed 16 bit Little
Endian
AO: [alsa] 44100Hz 2ch s16le (2 bps)
Building audio filter chain for 44100Hz/2ch/s16le ->
44100Hz/2ch/s16le...
Starting playback...
VDec: vo config request - 512 x 288 (preferred csp: Planar YV12)
VDec: using Planar YV12 as output csp (no 0)
Movie-Aspect is undefined - no prescaling applied.
VO: [xv] 512x288 => 512x288 Planar YV12 [fs] [zoom]
alsa-uninit: pcm closed-0.012 ct: -0.006 199/199 8% 0% 0.6% 2 0
Exiting... (Quit)
_______________________________________________
mythtv-users mailing list
[email protected]
http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
