I bought one of these in the link above and like it. If Lance still sells them. I use it for bench testing/proto work. It's adjustable which makes it nice for certain apps. John Taylor www.tayloredge.com has a real nice module that's pretty much plug and play and works real well also adjustable. Kos www.kosbo.com also sells one. In all I found that having one for the bench was required because once you start playing with neon your hooked. Plus you should be checking those nixies before installing them the be sure they actually work.
________________________________ From: Imbanon <[email protected]> To: neonixie-l <[email protected]> Sent: Sunday, October 9, 2011 10:08 AM Subject: [neonixie-l] Re: Disposable camera as power supply Thanks for your reply guys! And so I have gave up on my current supply, and decided to make my own. I didn't want to make my own as I thought that it will be the most expensive option, but I was wrong. Seems like all these pre-made supplys are around 20 bucks, a bit less, and for that kind of money I can make 5 of these http://www.ledsales.com.au/kits/nixie_supply.pdf ,and still have a lot of spare parts! Does anyone have any experience with these? Are they alright? Thanks again! On Oct 9, 6:25 pm, "MrNixie (UK)" <[email protected]> wrote: > A couple of points. > > You are going to need more than 0.2-0.3 mA to fully light a nixie > tube. Otherwise, you will see gaps in the numerals. > > A camera flash power supply has DREADFUL efficiency, is usually > designed to work from a 1.5V battery, and does so by pulling HUGE > currents - often over 1 amp. Here are the reasons why. > > Assume you need a 200V power supply, and at about 6 mA. That's 1.2W > out. The simple circuit found in cameras will be no better than 50% > efficient, so that's at least 2W in. Even with a fully charged > battery, that's 2/1.5 OVER ONE AMP in!! so you've got to build a power > supply capable of delivering over an amp, at one and a half volts, > just to pamper to your camera circuit. Why bother? > > John points out several alternatives; I would further add that I have > seen small custom-built power supply modules on eBay that will run > from a much more convenient 12V or thereabouts, and return much better > efficiencies. If you are wary of building your own, then certainly > look at one of these: > > http://www.ebay.co.uk/itm/NIXIE-TUBE-POWER-SUPPLY-MODULE-CLOCK-2-OUTP... > > ALSO! A camera flash power supply will be designed to charge a much > larger capacitor (for the flash) than these custom supplies like the > ones above, and this is capable of giving you a much bigger BELT when > you put yourself across that open circuit 330V, than a smaller, > current limited 180V supply. And, no matter how careful you are, > sooner or later you will do this! Alas, I know this... :( > > Laurence (AKA MrNixie, UK) > > On Oct 9, 3:08 am, John Rehwinkel <[email protected]> wrote: > > > > > > > > > > I've just got my IN-14 tubes and started experimenting on my first > > > nixie project - the clock, of course! For now I am using a disposable > > > camera as my power supply. Shorted out with an amp meter, it gives a > > > steady 12.8mA at 330V, which is better than expected. > > > More accurately, it pushes 12.8mA through a short at zero volts. I'm > > guessing > > the 330V is no load. So in-between, you're getting less than 330 volts at > > less > > than 12.8mA. > > > > So my question is; should I continue bothering with this power supply > > > (should it even be used for 6 tubes) and try to fix my schematics, or > > > just make my own power supply which I am not so fond of. > > > I'm guessing the camera supply just isn't up to the job, sad to say, but > > likely. > > > So there are a few ways you could proceed. If there are more where that > > came from, you could use six camera supplies, one for each tube. That > > might work, and would be amusing. Otherwise, you'd have to come up > > with the voltage some other way. The easiest way is probably to buy a > > ready-made supply like the Tayloredge ones. They're small, reliable, and > > very cost effective at $13 apiece, and you don't have to make your own. > > > Alternatively, if you're using an AC supply, you can use a transformer in > > reverse to step-up the voltage, and rectify that. Three parts (transformer, > > diode, and capacitor) and you're there (you can steal the capacitor and > > probably the diode from the camera supply). > > > > Can driving nixies at such low voltage and current damage my nixies? > > > Yes, running them underdriven like that can lead to cathode poisoning. > > It can be reversed, but it's disappointing when it happens. > > > - John KG4L -- You received this message because you are subscribed to the Google Groups "neonixie-l" group. To post to this group, send an email to [email protected]. To unsubscribe from this group, send email to [email protected]. For more options, visit this group at http://groups.google.com/group/neonixie-l?hl=en-GB. -- You received this message because you are subscribed to the Google Groups "neonixie-l" group. To post to this group, send an email to [email protected]. To unsubscribe from this group, send email to [email protected]. For more options, visit this group at http://groups.google.com/group/neonixie-l?hl=en-GB.
