On 16-05-21 09:53 PM, Instrument Resources of America wrote:
'Medlabs' was a typo on my part just now in that last message. I had
been sending to 'madlabs' all along with no luck, always rejected. Sent
to [email protected] again just now. Rejected again on the second
go round. Here is a partial copy of the message that I'm getting, Ira
[email protected] (after RCPT TO): 554 BLK_SYS_15 IP Address
(69.168.97.48) of the sender was found in DNSBL MailSpike-BL-W and was
therefore refused.
Not wanting to stray this far off topic but that is saying that the
destination e-mail server thinks that the sending mail server is on a
spam blacklist. 69.168.97.48 is the sending IP adddress and it appears
to be from an ISP in Buffalo NY called Synacor using a server called
smtp.hughes.net
perhaps IRA has to get his Internet provider to get the address taken
off the blacklist.
the blacklist seems to be run by http://mailspike.org/
there tools show :
Matches found for 69.168.97.48 (smtp.hughes.net)
Worst possible reputation
Worst possible reputation
I did submit a delist request to try to open that blacklist up FWIW. so
try again. But if one of the ISP's other customers is sending spam it
will close up quickly.
On 5/21/2016 4:22 PM, David Forbes wrote:
madlabs, not medlabs.
On 5/21/16 2:54 PM, Instrument Resources of America wrote:
I've tried twice now Johnathan to respond to you on this, and both times
the message comes back to me as being undeliverable. To; J PEAKALL@
MEDLABS.INFO Ira.
On 5/21/2016 12:00 PM, Jonathan Peakall wrote:
Hi All,
A little OT, but there are some CRT folks on this list.
I am working on a Hallicrafters SP-44 Skyrider Panadapter. I have done
a recap/re-resistor job on it. The CRT display isn't quite right, the
baseline is uneven in width, about right on the left but too wide on
the right. If anyone has some insight as to what could be causing it,
I would be very appreciative.
PLEASE REPLY OFF LIST : jpeakall AT madlabs DOT info
Many thanks folks!
Jonathan
--
You received this message because you are subscribed to the Google
Groups "neonixie-l" group.
To unsubscribe from this group and stop receiving emails from it, send
an email to [email protected]
<mailto:[email protected]>.
To post to this group, send email to [email protected]
<mailto:[email protected]>.
To view this discussion on the web, visit
https://groups.google.com/d/msgid/neonixie-l/016b9265-0a1c-5396-3f83-5380bf85f2a9%40HUGHES.NET
<https://groups.google.com/d/msgid/neonixie-l/016b9265-0a1c-5396-3f83-5380bf85f2a9%40HUGHES.NET?utm_medium=email&utm_source=footer>.
For more options, visit https://groups.google.com/d/optout.
--
Charles MacDonald Stittsville Ontario
[email protected] Just Beyond the Fringe
No Microsoft Products were used in sending this e-mail.
--
You received this message because you are subscribed to the Google Groups
"neonixie-l" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To post to this group, send an email to [email protected].
To view this discussion on the web, visit
https://groups.google.com/d/msgid/neonixie-l/57411A5C.9030501%40zeusprune.ca.
For more options, visit https://groups.google.com/d/optout.
