Re: NEOTEK: Neotek Series 1 (not E) - Direct Out

[Jared]

I believe you need to wire the insert send and return together. Then you need to add a 10k log pot as the output fader. I know some people like to destroy the pan pot and us it as the output fader but I think it is best to add a new pot and leave the pan pot alone. Use the direct out as your output. Hope that helps, Jared -----Original Message----- From: "Jürgen Wirtz" Sent: Feb 3, 2010 4:19 AM To: neotek@analogbros.com Subject: Re: NEOTEK: Neotek Series 1 (not E) - Direct Out Hello Tom, thanks a lot for your Email. I am a little bit confused with the schematics of the Series 1 Input Module. Is it just necessay to connect Mic In and Direct Out in order to use it as a Mic Preamp? I have only the Input-modul to rack up (no console or patchbay). Do I need to hardwire the Insert Send/Return in order to get a signal, or do I need to put in a fixed resistor to replace Fader? Regards, Juergen -------- Original-Nachricht -------- Datum: Wed, 27 Jan 2010 08:42:37 -0600 Von: "Tom Gorichanaz" <t...@jptech.com> An: "'"Jürgen Wirtz"'" <juergenwi...@gmx.de> Betreff: RE: NEOTEK: Rackin Neotek Series 1 (not E) - Output Ideas? Hello,   I have a Series 1 console (not E) and I use the direct outs with EQ  on each channel all the time. So, I believe all Series 1 modules 'Direct Outs' should contain the EQ signal as well. (I could be wrong though!) As far as balancing the outputs; I have wired the direct outs to my converters by connecting Cold and Neutral together and of course leaving Hot alone. I plan on eventually balancing the outs with transformers but this way is a quick way which usually works. At the very least, it is a good way to test to make sure everything is working.   Hope this helps!   Take care, Tom   -----Original Message----- From: neotek-ow...@analogbros.com [mailto:neotek-ow...@analogbros.com]On Behalf Of "Jürgen Wirtz" Sent: Tuesday, January 26, 2010 3:49 PM To: neotek@analogbros.com Subject: NEOTEK: Rackin Neotek Series 1 (not E) - Output Ideas? Hello, I am starting my racking Project with Series 1 Input Module. Any better idea what to use for an Output but Echo Send C in Pre-Fader Mode? As far as I understood the Direct Out doesn´t carry the EQ Signal - right? Therefore had the idea to use the Post Echo Send to get an adjustable Output Trim. Any advice welcome :-) Regards, Juergen PS: Did anyone realize a balanced Output for this Unit? -- Music Production & Audio Services Juergen Wirtz http://www.juergenwirtz.com Jetzt kostenlos herunterladen: Internet Explorer 8 und Mozilla Firefox 3.5 - sicherer, schneller und einfacher! http://portal.gmx.net/de/go/atbrowser -- Music Production & Audio Services Juergen Wirtz http://www.juergenwirtz.com Jetzt kostenlos herunterladen: Internet Explorer 8 und Mozilla Firefox 3.5 - sicherer, schneller und einfacher! http://portal.gmx.net/de/go/chbrowser -- Music Production & Audio Services Juergen Wirtz http://www.juergenwirtz.com GRATIS für alle GMX-Mitglieder: Die maxdome Movie-FLAT! Jetzt freischalten unter http://portal.gmx.net/de/go/maxdome01 ------ View the list online at: http://www.mail-archive.com/neotek@analogbros.com You can unsubscribe at anytime by sending an email to mailto:imail...@analogbros.com with "unsubscribe neotek" in the message body. If you have any difficulties, or questions --please send an email to mailto:l...@analogbros.com. The Neotek list is lovingly hosted by Catapult Web. Remember that any message or reply sent to the list will be automatically forwarded to all subscribers. Vive Le Neotek! Thanks.