Hi Jared, Thanks for the cable offer! I'd probably need approx. 15-18 ft. What kind of cable is it?
Thanks, Dave ---- Original Message ---- From: [email protected] To: [email protected] Subject: Re: NEOTEK: EDAC Connections Date: Mon, 5 Apr 2010 10:42:28 -0500 (GMT-05:00) >Hey dave > >I have some left over cable from when I extended my power supply >runs. If your interested I can dig it out and let you know what I >have. > >Take care, >Jared > > >-----Original Message----- >>From: [email protected] >>Sent: Apr 2, 2010 4:10 PM >>To: [email protected] >>Subject: Re: NEOTEK: EDAC Connections >> >>Ike, >> I hooked everything up according to your code using the black/grey >>wire for black/white and fired it up. I'm playing CDs back through >>tape 1 right now. It sounds great. The VU meters aren't lighting up >>or doing anything. I've only got one power supply. The sticker on >the >>back says PS-2. There's a slight hum coming from the supply, but >>that's probably natural. Is it possible to get a longer supply cable >>so I can put it in another room? >> >>Thanks, >>Dave >> >>---- Original Message ---- >>From: [email protected] >>To: [email protected] >>Subject: Re: NEOTEK: EDAC Connections >>Date: Fri, 02 Apr 2010 14:37:28 -0400 >> >>>Hi David, >>> 1st off, I /believe/ that the color code that I gave you was >the >>> >>>Neotek "standard". However, I haven't seen this written down many >>>places, so I also believe that whoever hooked up may of these >>>supplies >>>just made it up as they went along. >>> 2nd, the black/gray is the same as the black/white >>> 3rd, as long as each wire goes to the same terminal at each >end >>>the >>>color doesn't really matter. HOWEVER, I think it would be a good >idea >>>if >>>you made the color code match what I sent you. >>> By the way, you mentioned that this is a 40 channel desk...do >>>you >>>have one power supply, or two? >>>best, >>>Ike >>> >>> >>>On 4/2/2010 12:28 PM, [email protected] wrote: >>>> I'm finding some inconsistencies with the power supply/console >>>> wiring. The way the wiring came connected on the power supply is >>>> listed below. My supply cable has a black wire with grey stripes >>>> connected to the Bi Polar Ground (maybe this wire is considered >the >>>> "black/white" wire?). Here's how I received the power supply with >>>the >>>> supply cable already connected to it: >>>> >>>> TOP ROW: >>>> -18v..................Blue >>>> -18v..................Blue/Black >>>> Bi polar Ground.......Black >>>> Bi Polar Ground.......Black/Grey (black/white?) >>>> +18v..................Red >>>> +18v..................Red/Black >>>> >>>> BOTTOM ROW: >>>> >>>> +48v..................Green >>>> Phantom Ground........Green/Black >>>> +35v..................White >>>> Meter Ground..........White/Black >>>> -25v..................Orange >>>> Logic Ground..........Orange/Black >>>> >>>> The Black/Grey wire is confusing me, as well as the green wire >>>which >>>> is connected to the +48V terminal (Ike, you mentioned that the >+48v >>>> should be white). Any ideas? >>>> >>>> >>>> >>>> ---- Original Message ---- >>>> From: [email protected] >>>> To: [email protected] >>>> Subject: Re: NEOTEK: EDAC Connections >>>> Date: Wed, 31 Mar 2010 09:52:26 -0400 >>>> >>>> >>>>> Here's an idea: why not build some DB-25 to 1/4" snakes to adapt >>>the >>>>> >>>>> existing PT cables? That way you don't have to touch the edac >end, >>>>> and >>>>> you will be able to interface with most recording devices, now >and >>>in >>>>> >>>>> the future. >>>>> Best >>>>> Ike >>>>> >>>>> Sent from my iPhone >>>>> >>>>> On 2010-03-30, at 5:40 PM, [email protected] wrote: >>>>> >>>>> >>>>>> Ike, >>>>>> All of the cable snakes have edac connectors on the board >end. >>>I >>>>>> have 2 HD24XR machines that only accept 1/4" plugs, so I'll >have >>>to >>>>>> change those over. I'm going to take it slow and tackle the >>>>>> connections as I go. I may have to make some changes on the >>>>>> multitrack returns at the board, in which case I'll probably >need >>>>>> >>>>> to >>>>> >>>>>> figure out the pin layout so I can return signal to all 40 >>>channels >>>>>> if I need to. The board is 40x26x8. >>>>>> >>>>>> Dave >>>>>> >>>>>> ---- Original Message ---- >>>>>> From: [email protected] >>>>>> To: [email protected] >>>>>> Subject: Re: NEOTEK: Power Supply Connections >>>>>> Date: Tue, 30 Mar 2010 12:31:22 -0400 >>>>>> >>>>>> >>>>>>> Hi David >>>>>>> If your edac cons already have cable in them you should >>>only >>>>>>> have to re- terminate the other end (don't the Alesis decks >use >>>a >>>>>>> >>>>> 56 >>>>> >>>>>>> pin edac for I/O)? >>>>>>> In any case edac product including pins and tooling are >>>>>>> available from digi-key and others. >>>>>>> Reverb 1-4 is probably the Aux 1-4 sends that you would >>>plug >>>>>>> >>>>>>> into your fx units. >>>>>>> Best >>>>>>> Ike >>>>>>> >>>>>>> Sent from my iPhone >>>>>>> >>>>>>> On 2010-03-30, at 11:09 AM, [email protected] wrote: >>>>>>> >>>>>>> >>>>>>>> Thanks again Ike, >>>>>>>> I've got an edac snake for the master section. The snake is >>>>>>>> >>>>>>> labled >>>>>>> >>>>>>>> like this: >>>>>>>> >>>>>>>> Cue 1& 2 In L-R >>>>>>>> >>>>>> >>>>> ------ >>>>> >>>>> View the list online at: >>>>> http://www.mail-archive.com/[email protected] >>>>> >>>>> You can unsubscribe at anytime by sending an email to >>>>> mailto:[email protected] with "unsubscribe neotek" in the >>>>> message body. If you have any difficulties, or questions >--please >>>>> send an email to mailto:[email protected]. >>>>> >>>>> The Neotek list is lovingly hosted by Catapult Web. Remember >that >>>any >>>>> message or reply sent to the list will be automatically >forwarded >>>to >>>>> all subscribers. >>>>> >>>>> Vive Le Neotek! >>>>> >>>>> Thanks. >>>>> >>>> >>>> ------ >>>> >>>> View the list online at: >>>http://www.mail-archive.com/[email protected] >>>> >>>> You can unsubscribe at anytime by sending an email to >>>mailto:[email protected] with "unsubscribe neotek" in the >>>message body. If you have any difficulties, or questions --please >>>send an email to mailto:[email protected]. >>>> >>>> The Neotek list is lovingly hosted by Catapult Web. Remember that >>>any message or reply sent to the list will be automatically >forwarded >>>to all subscribers. >>>> >>>> Vive Le Neotek! >>>> >>>> Thanks. >>>> >>>> >>>> >>> >>>-- >>>Ike Zimbel >>>Zimbel Audio Productions Ltd. >>>Toronto >>>416-720-0887 >>> >>>"Studio House Calls". Authorized Warranty service for Allen& >Heath, >>>Clear-Com, Drawmer, Soundcraft, SPL and Yamaha. Repairs and >upgrades >>>to >>>analog audio equipment including: AMEK, dbx, Neve, Neotek, MCI, >>>Soundcraft and more. Ask about our RF Frequency co-ordination >>>services! >>>www.zimbelaudio.com >>> >>>------ >>> >>>View the list online at: >>>http://www.mail-archive.com/[email protected] >>> >>>You can unsubscribe at anytime by sending an email to >>>mailto:[email protected] with "unsubscribe neotek" in the >>>message body. If you have any difficulties, or questions --please >>>send an email to mailto:[email protected]. >>> >>>The Neotek list is lovingly hosted by Catapult Web. Remember that >any >>>message or reply sent to the list will be automatically forwarded >to >>>all subscribers. >>> >>>Vive Le Neotek! >>> >>>Thanks. >> >> >>------ >> >>View the list online at: >http://www.mail-archive.com/[email protected] >> >>You can unsubscribe at anytime by sending an email to >mailto:[email protected] with "unsubscribe neotek" in the >message body. If you have any difficulties, or questions --please >send an email to mailto:[email protected]. >> >>The Neotek list is lovingly hosted by Catapult Web. Remember that >any message or reply sent to the list will be automatically forwarded >to all subscribers. >> >>Vive Le Neotek! >> >>Thanks. > >------ > >View the list online at: >http://www.mail-archive.com/[email protected] > >You can unsubscribe at anytime by sending an email to >mailto:[email protected] with "unsubscribe neotek" in the >message body. If you have any difficulties, or questions --please >send an email to mailto:[email protected]. > >The Neotek list is lovingly hosted by Catapult Web. Remember that any >message or reply sent to the list will be automatically forwarded to >all subscribers. > >Vive Le Neotek! > >Thanks. ------ View the list online at: http://www.mail-archive.com/[email protected] You can unsubscribe at anytime by sending an email to mailto:[email protected] with "unsubscribe neotek" in the message body. If you have any difficulties, or questions --please send an email to mailto:[email protected]. The Neotek list is lovingly hosted by Catapult Web. Remember that any message or reply sent to the list will be automatically forwarded to all subscribers. Vive Le Neotek! Thanks.
