i do own a phone, just that it's not a smart-phone, i dislike them. :)
> From [email protected] Mon May 7 16:41:54 2018 > From: Hisashi T Fujinaka <[email protected]> > X-X-Sender: [email protected] > To: Kathe <[email protected]> > cc: [email protected], [email protected] > Subject: Re: 8.0 rc1 barfs during install > > I thought everyone owned a phone nowadays, but that's just me I guess. > > On Mon, 7 May 2018, Kathe wrote: > > > umnn, i don't have the equipment to get the video of the screen. > > i can provide reports using other operating systems, do let me > > know. > > > >> From [email protected] Mon May 7 > >> 16:08:41 2018 > >> From: Hisashi T Fujinaka <[email protected]> > >> X-X-Sender: [email protected] > >> To: Kathe <[email protected]> > >> cc: [email protected], [email protected] > >> Subject: Re: 8.0 rc1 barfs during install > >> Sender: [email protected] > >> > >> My guess is that you're going to have to get a video of the screen > >> during installation. > >> > >> On Mon, 7 May 2018, Kathe wrote: > >> > >>>> From [email protected] Mon May 7 > >>>> 15:50:58 2018 > >>>> From: Martin Husemann <[email protected]> > >>>> To: Kathe <[email protected]> > >>>> Cc: [email protected] > >>>> Subject: Re: 8.0 rc1 barfs during install > >>>> Sender: [email protected] > >>>> > >>>> On Mon, May 07, 2018 at 03:46:33PM +0000, Kathe wrote: > >>>>> i have an amd64 system which runs well with freebsd, openbsd and ubuntu. > >>>>> with netbsd 8.0 rc1, it barfs while outputing the message below; > >>>>> sdhc0: adma error, status ff > >>>>> sdhc0: timeout waiting for mask 0x3 value 0 (state=0xffffffff) > >>>>> sdhc0: command or data phase inhibited > >>>>> sdhc0: timeout waiting for mask 0x3 value 0 (state=0xffffffff) > >>>>> sdhc0: command or data phase inhibited > >>>> > >>>> Could you provide any details? > >>>> Does it hang at that point, just wait for a bit and then continue to > >>>> boot? > >>>> If possible send the full output of the dmesg command, please. > >>>> > >>>> Martin > >>>> > >>> > >>> my system works well with freebsd, openbsd, ubuntu. > >>> under netbsd 8.0 rc1, the following message keeps getting printed; > >>> sdhc0: adma error, status ff > >>> sdhc0: timeout waiting for mask 0x3 value 0 (state=0xffffffff) > >>> sdhc0: command or data phase inhibited > >>> sdhc0: timeout waiting for mask 0x1 value 0 (state=0xffffffff) > >>> sdhc0: command or data phase inhibited > >>> sdhc0: timeout waiting for mask 0x1 value 0 (state=0xffffffff) > >>> sdhc0: command or data phase inhibited > >>> sdhc0: timeout waiting for mask 0x3 value 0 (state=0xffffffff) > >>> sdhc0: command or data phase inhibited > >>> sdmmc0: sdmmc_mem_enable failed with error 60 > >>> sdmmc0: couldn't enable card: 60 > >>> > >>> i can't get to the point of plucking out the dmesg, the message > >>> above keeps getting repeated till the point i power-down the > >>> system. > >>> > >> > >> -- > >> Hisashi T Fujinaka - [email protected] > >> BSEE + BSChem + BAEnglish + MSCS + $2.50 = coffee > >> > > > > -- > Hisashi T Fujinaka - [email protected] > BSEE + BSChem + BAEnglish + MSCS + $2.50 = coffee >
