You are running the wrong kernel. Change to kernel-2.2.14-15mdk.i596.rpm located
in
/mnt/cdrom/Mandrake/RPMS
jero wrote:
> If I were you, I'd look into /var/log/messages (that's the message log when
> booting up). it'll give reasons if there are any problems. And I understand
> how you feel, i've got pretty much the same problem on my laptop. I'm gonna
> be upgrading to mandrake 7.02, do a recompile of the kernel and move the new
> system-map to the /etc directory aqnd HOPE that that solves my problem! :)
>
> Jero
>
> Carlos Salazar Mtz wrote:
>
> > Jero: I've just run "setup" and pcmcia service appears like this: [*]pcmcia
> >
> > when my system boots, when it comes up to finding module dependencies, it
> > first passes through "starting network" and it says "delaying
> > inicialization"...."failed". Few seconds later ir appears: "starting pcmcia
> > [ok]".
> > In the other hand, at console, if i want to see if the system detected my
> > cards I run "cardctl ident" or "cardctl config", and the answer of both is:
> > "no pcmcia driver in /proc/devices"
> > DO YOU HAVE ANY IDEA?
> >
> > -----Mensaje original-----
> > De: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]
> > Enviado el: martes 21 de marzo de 2000 11:18
> > Para: [EMAIL PROTECTED]
> > Asunto: Re: RV: [newbie] 3Com 3CXe589E PCMCIA ETHERNET CARD
> >
> > the pcmcia services ARE running right?
> >
> > Jero
> >
> > Carlos Salazar Mtz writes:
> >
> > >
> > > Hi, I've been spending 2 weeks trying to install my 3Com 3CXe589E PCMCIA
> > > ETHERNET CARD on a TOSHIBA 2500CDS with MANDRAKE 7.0, and just can't do
> > it.
> > > FIRST, at linux installation (when it asks if you want to configure the
> > > net),it recognizes the card and actually it is supposed to make it work in
> > > order to download something (crypt...) from an ftp site. It says pcmcia
> > > probe found 1 net devices, found driver for 3c589_cs....
> > > ....insmod /modules/pcmcia_core.o.........insmod/modules/3c589_cs.o
> > > ............... it finishes installing linux succesfully and restarts..
> > > WHEN it tries to find module dependencies it shows nothing about pcmcia,
> > and
> > > when it comes up to network inicialization it says:
> > > network inicialization delayed.......[failed]
> > > AFTER logging in, if I run "cardctl ident" it says "no pcmcia driver in
> > > /proc/devices", and when I run "cardctl config" it says the same thing,
> > when
> > > it is supposed to say something about the cards it detects.
> > > WHAT i think is that this kernel version (2.2.14-1mdklinus) does't support
> > > pcmcia or at list doesn't have the correct modules, because it doesn't
> > even
> > > have a "pcmcia" subdirectory (/lib/modules/2.2.14-1mdklinus/pcmcia) where
> > i
> > > can find "pcmcia_core.o" and "3c589_cs.o" in order to run:
> > > "insmod [directory] pcmcia_core.o"
> > > What I tried is:
> > > insmod /lib/modules/2.2.14-12mdk/pcmcia/pcmcia_core.o, and the answer was:
> > > "kernel-module version mismatch
> > > /lib/modules/2.2.14-12mdk/pcmcia/pcmcia_core.o was compiled for kernel
> > > version 2.2.14-15mdk while this kernel is version 2.2.14-1mdklinus"
> > > BUT THE PROBLEM IS THAT MY VERSION (2.2.14-1mdklinus) DOES NOT HAVE
> > ANYTHING
> > > LIKE "pcmcia_core.o" or "3c589_cs.o" IN ITS LIBRARIES.
> > >
> > > PLEASE HELP ME !!!!!!!!!!!
> > >
