Good for you. Nice to here you haven't given up. Enjoy the software. Roman Dacia and AzureRose wrote: > > Cool. Congrats and enjoy. > > Dacia > --- A J Benamu <[EMAIL PROTECTED]> wrote: > > Hi guys, > > > > I am up and running.. Internet is ok.... THANKS A > > LOT... > > > > AJ > > > > -----Original Message----- > > From: Dacia and AzureRose > > [mailto:[EMAIL PROTECTED]] > > Sent: Saturday, July 08, 2000 7:32 PM > > To: [EMAIL PROTECTED] > > Subject: RE: [newbie] Ethernet problems. > > > > > > WAIT! > > > > I have @home and I just got this configured in linux > > last night. On the receipt that they installation > > person left are your DNS addresses, IP address, > > subnet > > mask and gateway address. If you don't have that > > piece of paper or can't make sense of it, call @ > > home > > and ask them for that info. > > > > Open the network utility in DrakConf. Enter your > > computer name with the name @home gave you like > > this: > > > > c652933-a.sttln1.wa.home.com > > > > where the above reflects the information they gave > > you. Choose manual in the configuration for eth0 > > and > > enter the IP address and subnet mask there. Go to > > the > > DNS section and enter your primary and secondary DNS > > addresses. Go to the gateway section and enter your > > gateway address. Quit until it wants to apply the > > changes. Let it do that. You should be able to > > access the internet immediately. > > > > > > Dacia > > > > --- A J Benamu <[EMAIL PROTECTED]> wrote: > > > Roman, > > > > > > No luck there.. I think I will give up on Linux > > and > > > the Internet.. It is > > > definitely easier with Windows... MUCH EASIER!!!!! > > > > > > AJ > > > > > > -----Original Message----- > > > From: Romanator [mailto:[EMAIL PROTECTED]] > > > Sent: Saturday, July 08, 2000 6:23 PM > > > To: [EMAIL PROTECTED] > > > Cc: A J Benamu > > > Subject: Re: [newbie] Ethernet problems. > > > > > > > > > Hi AJ, > > > > > > I have attached a link to a url that will get you > > up > > > and running. I'm an > > > @Home cable user and I had one heck of a time > > > getting logged on. After > > > reading this, everything was working okay. > > > > > > > > > http://members.home.net/randal.leavitt/CableModemConnectionNotes.html > > > > > > Good Luck! > > > > > > Roman > > > > > > > > > A J Benamu wrote: > > > > > > > > HI Ralph, > > > > > > > > I finally got my HP Ethernet card configured.. > > but > > > I still don't have > > > > internet.. > > > > Does anybody know how to configure the @Home > > > service (Cable Modem). > > > > > > > > Thanks, > > > > > > > > AJ > > > > > > > > -----Original Message----- > > > > From: Ralph Day [mailto:[EMAIL PROTECTED]] > > > > Sent: Saturday, July 08, 2000 8:59 AM > > > > To: [EMAIL PROTECTED] > > > > Subject: Re: [newbie] Ethernet problems. > > > > > > > > OK, then we are going to need more information. > > > What exactly does "can't > > > > configure" mean? What have you tried so far? > > If > > > you have a working Win98 > > > > install, how is the card configured there? Any > > > messages about the adapter > > > > in the log? This card works fine for me and is > > > supported using the > > > RTL8139 > > > > driver. > > > > > > > > - Ralph > > > > > > > > ----- Original Message ----- > > > > From: "A J Benamu" <[EMAIL PROTECTED]> > > > > To: <[EMAIL PROTECTED]> > > > > Sent: Friday, July 07, 2000 11:49 PM > > > > Subject: RE: [newbie] Ethernet problems. > > > > > > > > > I did what you said and still no ethernet card > > > working.. > > > > > > > > > > Any ideas? > > > > > > > > > > Thanks, > > > > > > > > > > AJ > > > > > > > > > > -----Original Message----- > > > > > From: Ralph Day [mailto:[EMAIL PROTECTED]] > > > > > Sent: Friday, July 07, 2000 11:51 PM > > > > > To: [EMAIL PROTECTED] > > > > > Subject: Re: [newbie] Ethernet problems. > > > > > > > > > > > > > > > On my HP with the same NIC card LM recognized > > > the card but I couldn't > > > get > > > > it > > > > > to work. I had to go into the BIOS setup and > > > change the OS from Windows > > > > to > > > > > Other (the same as PNP OS no in other BIOS) to > > > solve the problem. The > > > > > problem was that the IRQ for the card wasn't > > > getting automacally > > > assigned > > > > by > > > > > the BIOS and LM wasn't configuring the card > > > either. Changing the > > > setting > > > > > makes the BIOS assign an IRQ. > > > > > > > > > > - Ralph > > > > > > > > > > ----- Original Message ----- > > > > > From: "A J Benamu" <[EMAIL PROTECTED]> > > > > > To: <[EMAIL PROTECTED]> > > > > > Sent: Friday, July 07, 2000 7:01 PM > > > > > Subject: [newbie] Ethernet problems. > > > > > > > > > > > > > > > > > > > > > > Hi, > > > > > > > > > > > > I hope I can get my message across... > > > > > > I installed Linux Mandrake 7.0 in my Athlon > > > 700 machine.. Also using > > > Win > > > > > 98. > > > > > > > > > > > > I can't seem to configure my ethernet card. > > I > > > use cable modem to > > > access > > > > > the > > > > > > internet. > > > > > > > > > > > > The ethernet card is HP EN1207D-TX PCI > > 10/100 > > > Fast Ethernet Adapter. > > > > > > > > > > > > Can anybody help me? > > > > > > > > > > > > Why can't I configure my HP M90 with > > Mandrake? > > > > > > > > > > > > Thanks, > > > > > > > > > > > > AJ > > > > > > > > > __________________________________________________ > > Do You Yahoo!? > > Get Yahoo! Mail � Free email you can access from > > anywhere! > > http://mail.yahoo.com/ > > > > > > __________________________________________________ > Do You Yahoo!? > Get Yahoo! Mail � Free email you can access from anywhere! > http://mail.yahoo.com/
begin:vcard n:;Roman x-mozilla-html:FALSE adr:;;;;;; version:2.1 note:Roman - Register Linux User #179293 fn:Roman - Register Linux User #179293 end:vcard
