need to use something against the edge of cover.the mallet is too big to tap it directly.
ideas? On Apr 11, 10:27 pm, "Allen Thomas" <[email protected]> wrote: > Bump it with a rubber mallet. > Sent via BlackBerry by AT&T > > -----Original Message----- > From: dapperdan7 <[email protected]> > > Sender: [email protected] > Date: Mon, 11 Apr 2011 19:29:28 > To: Nighthawk Motorcycle Lovers!<[email protected]> > Reply-To: [email protected] > Subject: [Nighthawk Lovers] Re: in too deep? transmission replacement question > > yes im in reno.i have removed the bolts off the clutch cover. any idea > how to get cover off without damaging it? it seems like its on pretty > good > > On Apr 7, 10:06 am, "Scott McKinley" <[email protected]> wrote: > > Dan, are you located in Reno? > > Scott in Reno > > > -----Original Message----- > > From: [email protected] > > > [mailto:[email protected]] On Behalf Of dapperdan7 > > Sent: Thursday, April 07, 2011 9:57 AM > > To: Nighthawk Motorcycle Lovers! > > Subject: [Nighthawk Lovers] Re: in too deep? transmission replacement > > question > > > the nighthawk has 17000 miles, its in reno nevada. the reason i > > thought it was the tranny is because of sounds i heard before > > something seized up.the clutch feels fine.the engine still runs fine. > > like i said,i located a full tranny in california for 300 bux.i dont > > think in any way am i going to spend less than this. > > > On Apr 6, 8:30 pm, Joey Kelley <[email protected]> wrote: > > > Dan, > > > What is the tranny going to cost you total - shipping and such > > included? > > > Besides the tranny - what is the condition of the NH? > > > -Joey > > > > On Wed, Apr 6, 2011 at 7:17 PM, dapperdan7 <[email protected]> wrote: > > > > my tranny is shot on my 091 nighthawk 250.i have located an entire > > > > transmission at a california junkyard for just under 300 bux. my > > > > question: is it insane, if i take my time,to try rebuilding myself? i > > > > have worked on cars but am pretty much a novice with something this > > > > complex.i have the manual and the time and the tools.crazy to even > > > > attempt it? > > > > > thanx > > > > dan > > > > > -- > > > > You received this message because you are subscribed to the Google > > Groups "Nighthawk Motorcycle Lovers!" group. > > > > To post to this group, send email to [email protected]. > > > > To unsubscribe from this group, send email to > > [email protected]. > > > > For more options, visit this group > > athttp://groups.google.com/group/nighthawk_lovers?hl=en. > > > > -- > > > -Joey Kelley > > > JoeyKelley.com - My Life Online > > > JoeyFixesComputers.com - Its What I Do! > > > JoeyKelleyPhoto.com - Photographing Today, For Tomorrow > > > -- > > You received this message because you are subscribed to the Google Groups > > "Nighthawk Motorcycle Lovers!" group. > > To post to this group, send email to [email protected]. > > To unsubscribe from this group, send email to > > [email protected]. > > For more options, visit this group > > athttp://groups.google.com/group/nighthawk_lovers?hl=en. > > -- > You received this message because you are subscribed to the Google Groups > "Nighthawk Motorcycle Lovers!" group. > To post to this group, send email to [email protected]. > To unsubscribe from this group, send email to > [email protected]. > For more options, visit this group > athttp://groups.google.com/group/nighthawk_lovers?hl=en. -- You received this message because you are subscribed to the Google Groups "Nighthawk Motorcycle Lovers!" group. To post to this group, send email to [email protected]. To unsubscribe from this group, send email to [email protected]. For more options, visit this group at http://groups.google.com/group/nighthawk_lovers?hl=en.
