I'll try to find site when I get home. I would crimp on new spade connectors as well. As far as the heavy paint, be careful with chemical strippers, they can attack your plastic
On Thu, Jan 17, 2019, 12:19 PM Arthur Sheller <[email protected]> wrote: > Great where can I get a plug? Thanks! > > On Thu, Jan 17, 2019, 11:17 AM Darin Hatton <[email protected] wrote: > >> Thats what happens when you have loose or dirty connection . You should >> be able to release each pin from plug, new plugs are available. I replaced >> a couple on my silverwing that had got hot and partially melted. There is a >> small prong on each one holding it in the plug. You can use something very >> small to slide into plug on the prong and release it. I use a piece of 1/16 >> tig welding wire hammered flat >> >> On Thu, Jan 17, 2019, 12:08 PM Arthur Sheller <[email protected]> >> wrote: >> >>> Have ever replaced a wire plug? I have a plug that looks bad. >>> >>> On Mon, Jan 14, 2019, 6:38 PM Arthur Sheller <[email protected] >>> wrote: >>> >>>> Okay thanks! I'll look into that. Great job on the cafe racer! >>>> >>>> On Monday, January 14, 2019 at 6:03:58 PM UTC-6, roidfingers wrote: >>>>> >>>>> You could go get some aircraft stripper. They have it at most auto >>>>> part stores. Or get an orbital sander and 4 or 5 grades of paper and >>>>> remove >>>>> it. I need my tank that way. I have a post above about a café racer. Not >>>>> sure about the plastics. You better research that. May have to just rough >>>>> it up with sand paper, then prime and paint. >>>>> >>>>> On Monday, January 14, 2019 at 3:55:32 PM UTC-6, Arthur Sheller wrote: >>>>>> >>>>>> I'm a newbie to the Nighthawk club. A little over a year ago I was >>>>>> given a 1984 Nighthawk S that sat for about four years because it stopped >>>>>> running. The poor guy took it to a local shop and they told him the >>>>>> engine >>>>>> was bad and it would cost big bucks to fix it. He parked it and bought a >>>>>> Harley. He told me I could haul it off for scrap or whatever. >>>>>> >>>>>> I took it home and waited a year to mess with it, The fuel tank was >>>>>> rusty and the petcock drain bowl was packed with rust. Also one of the >>>>>> wires at the stop run switch had broken. >>>>>> >>>>>> I repaired the wire and cleaned the tank and petcock. She fired and >>>>>> idled like a new one. I was shocked since I thought the engine was bad. I >>>>>> rode it and was even more stunned because it ran great. >>>>>> >>>>>> So after reading all the reviews and studying the history I have the >>>>>> bug really bad. I'm in full restoration mode now. I attached a pic of >>>>>> what >>>>>> it looked like when I got it. >>>>>> I have my work cut out for me. What's the best way to prep or remove >>>>>> old paint? Thanks! >>>>>> >>>>> -- >>>> You received this message because you are subscribed to the Google >>>> Groups "Nighthawk Motorcycle Lovers!" group. >>>> To unsubscribe from this group and stop receiving emails from it, send >>>> an email to [email protected]. >>>> To post to this group, send email to [email protected]. >>>> Visit this group at https://groups.google.com/group/nighthawk_lovers. >>>> For more options, visit https://groups.google.com/d/optout. >>>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "Nighthawk Motorcycle Lovers!" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to [email protected]. >>> To post to this group, send email to [email protected]. >>> Visit this group at https://groups.google.com/group/nighthawk_lovers. >>> For more options, visit https://groups.google.com/d/optout. >>> >> -- >> You received this message because you are subscribed to the Google Groups >> "Nighthawk Motorcycle Lovers!" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> To post to this group, send email to [email protected]. >> Visit this group at https://groups.google.com/group/nighthawk_lovers. >> For more options, visit https://groups.google.com/d/optout. >> > -- > You received this message because you are subscribed to the Google Groups > "Nighthawk Motorcycle Lovers!" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To post to this group, send email to [email protected]. > Visit this group at https://groups.google.com/group/nighthawk_lovers. > For more options, visit https://groups.google.com/d/optout. > -- You received this message because you are subscribed to the Google Groups "Nighthawk Motorcycle Lovers!" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To post to this group, send email to [email protected]. Visit this group at https://groups.google.com/group/nighthawk_lovers. For more options, visit https://groups.google.com/d/optout.
