It sounds like you have done all the right things. Is there any chance you can loan us the device for a day? If so, contact support @ nsbasic.com directly, and we will make the arrangements.
George Henne NS BASIC Corporation http://www.nsbasic.com >I have purchased the latest CuWin5500, HMI device running Windows Embedded 6.0 > >http://www.cubloc.com/product/06_02.php > >I have downloaded NSBasic 8.20a, using my Serial , updating from 7.05b > >Everything seems to install/load OK. No error messages > >on the NSBasic IDE choose Tools>Options>Installer>Get Device Info shows > >Device processor Type 2577: >Device Type: SMDK2450 Board >Device OEM Info: Samsung Electronics >Device Version: 6 > >I have selected the Platform > >2577 - ARMV4/StrongARM/SA1100 > >Wanted to try running an NSBasic program, the Benchmark.nsb > >Active sync 4.5 connects, I am able to explore the CuWin5500, > >No error messages at all when uploading or running a program, > >but all I get is a Blank light gray screen, "X" in upper Right corner, a >tab created on the bottom with the name of the program, plus the rest of >the task bar icons , start button, etc. > >The unit is not lock up because I can open control panel etc. while the >blank screen is being shown. > >The only screen item in the Benchmark.nsb program is a Message Box, but >this does not show on the screen of the CuWin5500. > >I Have used NSBasic v 7.05b to program the CuWin3500, ab earlier version >of the device, which has CE5.0 installed. Worked very well. > >In thinking about this, I concluded that the controls were not being >registered. >It would seem that Windows CE6.0 does not use "regsvrce.exe" to register >the controls. > >I tried to run > >ShellExecute "open","regsvrce.exe","\Flash Disk\NSB BASIC\nsbasic >\MSCEComm.dll" > >ShellExecute "open","regsvrce.exe","\Flash Disk\NSB BASIC\nsbasic >\MSCEComDlg.dll" > >ShellExecute "open","regsvrce.exe","\Flash Disk\NSB BASIC\nsbasic >\MSCEFile.dll" > >ShellExecute "open","regsvrce.exe","\Flash Disk\NSB BASIC\nsbasic >\NSCEPictureBox.ocx" > >ShellExecute "open","regsvrce.exe","\Flash Disk\NSB BASIC\nsbasic >\newObjectsPack1.dll" > >ShellExecute "open","regsvrce.exe","\Flash Disk\NSB BASIC\nsbasic >\NSBComDlg.dll" > >ShellExecute "open","regsvrce.exe","\Flash Disk\NSB BASIC\nsbasic >\NSBControls.dll" > >ShellExecute "open","regsvrce.exe","\Flash Disk\NSB BASIC\nsbasic >\SerialCE.dll" > >ShellExecute "open","regsvrce.exe","\Flash Disk\NSB BASIC\nsbasic \DialogX.ocx" > >ShellExecute "open","regsvrce.exe","\Flash Disk\NSB BASIC\nsbasic >\vbscript.dll" > >ShellExecute "open","regsvrce.exe","\Flash Disk\NSB BASIC\nsbasic >\NSBWin32.dll" > >Bye > >Browsing the files on the CuWin5500, I did not find the file >"regsvrce.exe" > >So I am at a bit of a loss, NSBasic 8.02a should not require an >installed runtime on the device, and should have the ability to register >any controls > >Any assistance is appreciated > >Ben > > > > >------------------------------------ > >Yahoo! Groups Links > > > -- You received this message because you are subscribed to the Google Groups "nsb-ce" group. To post to this group, send email to nsb...@googlegroups.com. To unsubscribe from this group, send email to nsb-ce+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/nsb-ce?hl=en.