Hi George, Thankyou for the offer. I have sent several emails to supp...@nsbasic.com without any replys.
All I need is an address, and a choice of courier, and I will send you a unit. Thanks again Ben --- In nsbasic-ce@yahoogroups.com, "George Henne" <g...@...> wrote: > > It sounds like you have done all the right things. > > Is there any chance you can loan us the device for a day? If so, contact > support @ nsbasic.com directly, and we will make the arrangements. > > George Henne > NS BASIC Corporation > http://www.nsbasic.com > > >I have purchased the latest CuWin5500, HMI device running Windows > Embedded 6.0 > > > >http://www.cubloc.com/product/06_02.php > > > >I have downloaded NSBasic 8.20a, using my Serial , updating from 7.05b > > > >Everything seems to install/load OK. No error messages > > > >on the NSBasic IDE choose Tools>Options>Installer>Get Device Info shows > > > >Device processor Type 2577: > >Device Type: SMDK2450 Board > >Device OEM Info: Samsung Electronics > >Device Version: 6 > > > >I have selected the Platform > > > >2577 - ARMV4/StrongARM/SA1100 > > > >Wanted to try running an NSBasic program, the Benchmark.nsb > > > >Active sync 4.5 connects, I am able to explore the CuWin5500, > > > >No error messages at all when uploading or running a program, > > > >but all I get is a Blank light gray screen, "X" in upper Right corner, a > >tab created on the bottom with the name of the program, plus the rest of > >the task bar icons , start button, etc. > > > >The unit is not lock up because I can open control panel etc. while the > >blank screen is being shown. > > > >The only screen item in the Benchmark.nsb program is a Message Box, but > >this does not show on the screen of the CuWin5500. > > > >I Have used NSBasic v 7.05b to program the CuWin3500, ab earlier version > >of the device, which has CE5.0 installed. Worked very well. > > > >In thinking about this, I concluded that the controls were not being > >registered. > >It would seem that Windows CE6.0 does not use "regsvrce.exe" to register > >the controls. > > > >I tried to run > > > >ShellExecute "open","regsvrce.exe","\Flash Disk\NSB BASIC\nsbasic > >\MSCEComm.dll" > > > >ShellExecute "open","regsvrce.exe","\Flash Disk\NSB BASIC\nsbasic > >\MSCEComDlg.dll" > > > >ShellExecute "open","regsvrce.exe","\Flash Disk\NSB BASIC\nsbasic > >\MSCEFile.dll" > > > >ShellExecute "open","regsvrce.exe","\Flash Disk\NSB BASIC\nsbasic > >\NSCEPictureBox.ocx" > > > >ShellExecute "open","regsvrce.exe","\Flash Disk\NSB BASIC\nsbasic > >\newObjectsPack1.dll" > > > >ShellExecute "open","regsvrce.exe","\Flash Disk\NSB BASIC\nsbasic > >\NSBComDlg.dll" > > > >ShellExecute "open","regsvrce.exe","\Flash Disk\NSB BASIC\nsbasic > >\NSBControls.dll" > > > >ShellExecute "open","regsvrce.exe","\Flash Disk\NSB BASIC\nsbasic > >\SerialCE.dll" > > > >ShellExecute "open","regsvrce.exe","\Flash Disk\NSB BASIC\nsbasic > \DialogX.ocx" > > > >ShellExecute "open","regsvrce.exe","\Flash Disk\NSB BASIC\nsbasic > >\vbscript.dll" > > > >ShellExecute "open","regsvrce.exe","\Flash Disk\NSB BASIC\nsbasic > >\NSBWin32.dll" > > > >Bye > > > >Browsing the files on the CuWin5500, I did not find the file > >"regsvrce.exe" > > > >So I am at a bit of a loss, NSBasic 8.02a should not require an > >installed runtime on the device, and should have the ability to register > >any controls > > > >Any assistance is appreciated > > > >Ben > > > > > > > > > >------------------------------------ > > > >Yahoo! Groups Links > > > > > > > -- You received this message because you are subscribed to the Google Groups "nsb-ce" group. To post to this group, send email to nsb...@googlegroups.com. To unsubscribe from this group, send email to nsb-ce+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/nsb-ce?hl=en.