Hi Mike! Thank you very much! You gave a push in the right direction!
Mike Christie schrieb: > On the initiator side running 2.6.24 and 2.0.865.15, I > I simply booted both machines with 2.6.24 and now the connection handshake runs. iscsi_discovery 10.6.0.2 -tiser iscsiadm: No active sessions. iscsiadm: Could not read node record for iqn.2001-04.com.poseidon-de.inqbus.poseidon:disk1 10.6.0.2 3260 default Set target de.inqbus.poseidon:disk1 to automatic login over iser to portal 10.6.0.2:3260 Logging out of session [sid: 1, target: de.inqbus.poseidon:disk1, portal: 10.6.0.2,3260] Logout of [sid: 1, target: de.inqbus.poseidon:disk1, portal: 10.6.0.2,3260]: successful discovered 1 targets at 10.6.0.2 But then again a connection error occurs. dmesg on initiator: iser: iser_connect:connecting to: 10.6.0.2, port 0xbc0c iser: iser_cma_handler:event 0 conn ffff81021cd84b80 id ffff81021cd4e400 iser: iser_cma_handler:event 2 conn ffff81021cd84b80 id ffff81021cd4e400 iser: iser_create_ib_conn_res:setting conn ffff81021cd84b80 cma_id ffff81021cd4e400: fmr_pool ffff81021bd49ec0 qp ffff81021cde2200 iser: iser_cma_handler:event 9 conn ffff81021cd84b80 id ffff81021cd4e400 iser: iscsi_iser_ep_poll:ib conn ffff81021cd84b80 rc = 1 scsi7 : iSCSI Initiator over iSER, v.0.1 iser: iscsi_iser_conn_bind:binding iscsi conn ffff81021d401a58 to iser_conn ffff81021cd84b80 scsi 7:0:0:0: RAID IET Controller 0001 PQ: 0 ANSI: 5 scsi 7:0:0:1: Direct-Access IET VIRTUAL-DISK 0001 PQ: 0 ANSI: 5 sd 7:0:0:1: [sde] 83886080 512-byte hardware sectors (42950 MB) sd 7:0:0:1: [sde] Write Protect is off sd 7:0:0:1: [sde] Mode Sense: 79 00 00 08 sd 7:0:0:1: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 7:0:0:1: [sde] 83886080 512-byte hardware sectors (42950 MB) sd 7:0:0:1: [sde] Write Protect is off sd 7:0:0:1: [sde] Mode Sense: 79 00 00 08 sd 7:0:0:1: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sde: unknown partition table sd 7:0:0:1: [sde] Attached SCSI disk iser: iser_cma_handler:event 10 conn ffff81021cd84b80 id ffff81021cd4e400 connection1:0: iscsi: detected conn error (1011) iser: iscsi_iser_ep_disconnect:ib conn ffff81021cd84b80 state 3 iser: iser_cq_tasklet_fn:comp w. error op 0 status 5 iser: iser_cq_tasklet_fn:comp w. error op 0 status 5 iser: iser_cq_tasklet_fn:comp w. error op 0 status 5 iser: iser_cq_tasklet_fn:comp w. error op 0 status 5 iser: iser_free_ib_conn_res:freeing conn ffff81021cd84b80 cma_id ffff81021cd4e400 fmr pool ffff81021bd49ec0 qp ffff81021cde2200 iser: iser_device_try_release:device ffff81021bd497c0 refcount 0 iscsi: cmd 0x12 is not queued (6) sd 7:0:0:1: [sde] Synchronizing SCSI cache iscsi: cmd 0x35 is not queued (6) iscsi: cmd 0x35 is not queued (6) iscsi: cmd 0x35 is not queued (6) sd 7:0:0:1: [sde] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK Any hint? Best Regards Volker -- ==================================================== inqbus it-consulting +49 ( 341 ) 5643800 Dr. Volker Jaenisch http://www.inqbus.de Herloßsohnstr. 12 0 4 1 5 5 Leipzig N O T - F Ä L L E +49 ( 170 ) 3113748 ==================================================== --~--~---------~--~----~------------~-------~--~----~ You received this message because you are subscribed to the Google Groups "open-iscsi" group. To post to this group, send email to [email protected] To unsubscribe from this group, send email to [EMAIL PROTECTED] For more options, visit this group at http://groups.google.com/group/open-iscsi -~----------~----~----~----~------~----~------~--~---
