> On Nov 5, 2017, at 5:18 PM, Xingjun Chu <[email protected]> wrote:
>
> hi Luis
>
> thanks.
>
> is there a way to define a wild card match for example for any vlan header?
> doesnt have to be a specific one ? if there is an example code even better.
yes, just set vlan-id-present=true and skip vlan-id:
"vlan-match": {
"vlan-id": {
"vlan-id-present": true
}
},
>
> i tried to set a vlan match for example vlan id 100. when it is installed,
> the match entry in the ovs flow showd a vlan tci match with a vid 100 and a
> mask 1fff, i have no idea how the mask is set and by who, which doesnt
> actually match vlan 100 traffic for some reason.
I think these are OVS specifics, so I would recommend to check OVS
documentation.
>
> thanks
> Xingjun
> --------------------------------------------------
> Xingjun Chu Xingjun Chu
> M:
> E: [email protected]
> 2012实验室-渥太华光系统能力中心
> 2012 Laboratories-Ottawa Optical System Competency Centre
> 发件人：Luis Gomez
> 收件人：Xingjun Chu,
> 抄
> 送：[email protected],[email protected],[email protected],
> 时间：2017-11-05 19:44:18
> 主 题：Re: [openflowplugin-dev] A question regarding VLAN tagging and untagging
>
> Hi Xingjun, AFAIR you have to specify VLAN match when you set or pop vlan,
> not when you push.
>
>
> > On Nov 5, 2017, at 7:13 AM, Xingjun Chu <[email protected]> wrote:
> >
> > BTW,
> >
> > On top of the previous email, as an example, here is the flow table with
> > vlan pop action I dumped using openflow rest api. it is in config, but not
> > installed.
> >
> > {
> > "flow-node-inventory:table": [
> > {
> > "id": 80,
> > "flow": [
> > {
> > "id": "DEFAULT_PIPELINE_FLOW_80",
> > "hard-timeout": 0,
> > "idle-timeout": 0,
> > "match": {},
> > "instructions": {
> > "instruction": [
> > {
> > "order": 0,
> > "apply-actions": {
> > "action": [
> > {
> > "order": 0,
> > "pop-vlan-action": {}
> > }
> > ]
> > }
> > },
> > {
> > "order": 1,
> > "go-to-table": {
> > "table_id": 110
> > }
> > }
> > ]
> > },
> > "barrier": true,
> > "priority": 0,
> > "table_id": 80,
> > "flow-name": "DEFAULT_PIPELINE_FLOW_80"
> > }
> > ]
> > }
> > ]
> > }
> >
> >
> > thanks
> > Xingjun
> > From: Xingjun Chu
> > Sent: Sunday, November 05, 2017 9:28 AM
> > To: [email protected];
> > [email protected]
> > Cc: [email protected]
> > Subject: A question regarding VLAN tagging and untagging
> >
> > Hi,
> >
> > I have a couple of questions regarding the VLAN relevant action.
> >
> > 1) I have a table in the pipeline which does some L3 forwarding. it has
> > some entries to match dst ip, then modify dst dl address, dec-ttl,
> > resubmit. etc... Those flows get installed without problem.
> > .
> > Now I try to add a "VLAN strip or pop" into the action list of the flow
> > above for example as the first action , strip or pop VLAN, then modify dst
> > dl address, dec-ttl, resubmit, etc... I tried both strip or pop action,
> > but either way the flow didn't get installed. why is that?
> >
> > I even tried to just create a separate table with VLAN strip and resubmit
> > as the default entry, it doesn't get installed either.
> >
> > 2) also I found more strange thing is that If I need to push and set a VLAN
> > ID in the action, Ihave to have a VLAN match first, otherwise
> > the flow is not get installed.
> >
> > BTW I am doing this NOT using REST API of openflowplugin. but
> > programmatically using Action, Action builder etc...
> >
> > Any pointer is greatly appreciated.
> >
> > Thanks & Regards
> > Xingjun
> >
> >
> >
> >
> > _______________________________________________
> > openflowplugin-dev mailing list
> > [email protected]
> > https://lists.opendaylight.org/mailman/listinfo/openflowplugin-dev
_______________________________________________
openflowplugin-dev mailing list
[email protected]
https://lists.opendaylight.org/mailman/listinfo/openflowplugin-dev
