Il 14/06/2016 13:48, Uwe Bonnes ha scritto:
Hello,
does you ELF file load with another programmer? It the linker script all
right? Can you send me the Elf File in private mail? Or perhaps the outout
from "arm-none-eabi-readelf -a ....elf"
Bye
Hello,
I tried with STlink and the result is:
openocd -f interface/stlink-v2-1.cfg -f
/home/lorenzo/Progetti/EcceGui/demo/myboard_EK390.cfg -c "init; targets;
reset halt; wait_halt; poll; flash write_image erase unlock
Debug-EK390-0/LCDTest.elf; flash erase_check 0; reset run; shutdown"
Open On-Chip Debugger 0.10.0-dev-00321-gd4b7cbf (2016-05-31-10:18)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
Info : auto-selecting first available session transport "hla_swd". To
override use 'transport select <transport>'.
Info : The selected transport took over low-level target control. The
results might differ compared to plain JTAG/SWD
adapter speed: 2000 kHz
adapter_nsrst_delay: 100
srst_only separate srst_nogate srst_open_drain connect_deassert_srst
adapter speed: 600 kHz
Info : Unable to match requested speed 600 kHz, using 480 kHz
Info : Unable to match requested speed 600 kHz, using 480 kHz
Info : clock speed 480 kHz
Info : STLINK v2 JTAG v24 API v2 SWIM v11 VID 0x0483 PID 0x374B
Info : using stlink api v2
Info : Target voltage: 3.253755
Warn : Silicon bug: single stepping will enter pending exception handler!
Info : stm32f7x.cpu: hardware has 8 breakpoints, 4 watchpoints
TargetName Type Endian TapName State
-- ------------------ ---------- ------ ------------------ ------------
0* stm32f7x.cpu hla_target little stm32f7x.cpu running
stm32f7x.cpu: target state: halted
target halted due to debug-request, current mode: Thread
xPSR: 0x01000000 pc: 0xfffffffe msp: 0xfffffffc
background polling: on
TAP: stm32f7x.cpu (enabled)
stm32f7x.cpu: target state: halted
target halted due to debug-request, current mode: Thread
xPSR: 0x01000000 pc: 0xfffffffe msp: 0xfffffffc
auto erase enabled
auto unlock enabled
Info : device id = 0x10016449
Info : flash size = 1024kbytes
Error: timed out while waiting for target halted
stm32f7x.cpu: target state: halted
target halted due to debug-request, current mode: Handler HardFault
xPSR: 0x01000003 pc: 0xfffffffe msp: 0xffffffd8
Error: error waiting for target flash write algorithm
Error: error writing to flash at address 0x08000000 at offset 0x00000000
make: *** [progflash] Errore 1
Instead i have programmed it with success with DFU protocol dfu-util -d
0483:df11 -c 1 -i 0 -a 0 -s 0x08000000 -D LCDtest.bin
--
*Lorenzo Corti* | Ricerca e Sviluppo
*Eurek s.r.l. *Via Celletta 8/b | 40026 Imola (BO) - Italy | +39 *0542
609120*
[email protected] <mailto:[email protected]> | www.eurek.it
<http://www.eurek.it/>
------------------------------------------------------------------------------
What NetFlow Analyzer can do for you? Monitors network bandwidth and traffic
patterns at an interface-level. Reveals which users, apps, and protocols are
consuming the most bandwidth. Provides multi-vendor support for NetFlow,
J-Flow, sFlow and other flows. Make informed decisions using capacity
planning reports. https://ad.doubleclick.net/ddm/clk/305295220;132659582;e
_______________________________________________
OpenOCD-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/openocd-devel
