On Tue, 02 Aug 2011 17:09:13 -0500, Layne Edwards
<[email protected]> wrote:
> Andrew,
>
> Did you modify the eeprom extract hotplug for your board?
>
>
trunk/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
>
>
> Regards,
> Layne
Thanks for the tip, it now loads the firmware, but the interface still
doesn't show up.
I flashed some dd-wrt image that worked previously on the device. It looks
like they have
eeproms bundled along.
I checked the actual data in the mtd partition with dd-wrt's bundled
eeproms - looks like
everything is correct, all have the 50 30 00 header. Can it be some kind
of rfkill/gpio-controlled power circuit in there?
I'll experiment with dd-wrt's eeproms later and post the results.
Full dmesg log follows:
Linux version 2.6.39.2 (necromant@ilwyn) (gcc version 4.5.4 20110526
(prerelease) (Linaro GCC 4.5-2011.06-0) ) #13 Wed Aug 3 00:07:36 MSD 2011
prom: fw_arg0=00000001, fw_arg1=01f5bfb0, fw_arg2=01f5c3b0,
fw_arg3=00000000
env[0]: memsize=32
env[1]: initrd_start=0x00000000
env[2]: initrd_size=0x0
env[3]: flash_start=0xBF000000
env[4]: flash_size=0x400000
env[0]: memsize=32
env[1]: initrd_start=0x00000000
env[2]: initrd_size=0x0
env[3]: flash_start=0xBF000000
env[4]: flash_size=0x400000
bootconsole [early0] enabled
CPU revision is: 0001964c (MIPS 24Kc)
Ralink RT3350 id:1 rev:2 running at 320.00 MHz
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00002000
On node 0 totalpages: 8192
free_area_init_node: node 0, pgdat 8022b0a0, node_mem_map 81000000
Normal zone: 64 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 8128 pages, LIFO batch:0
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: board=MOFI3500-3GN
mtdparts=physmap-flash.0:192k(u-boot)ro,64k(devdata)ro,64k(devconf)ro,832k(kernel),2944k(rootfs),3776k@0x50000(firmware)
console=ttyS1,57600 rootfstype=squashfs,jffs2
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=0007a000
Readback ErrCtl register=0007a000
Memory: 29968k/32768k available (1890k kernel code, 2800k reserved, 331k
data, 152k init, 0k highmem)
SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:48
console [ttyS1] enabled, bootconsole disabled
Calibrating delay loop... 212.58 BogoMIPS (lpj=1062912)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is MoFi Network MOFI3500-3GN
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c)
2001-2006 Red Hat, Inc.
msgmni has been set to 58
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 13) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
physmap platform flash device: 00800000 at bf000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer
ID 0x0000c2 Chip ID 0x0022a8
physmap-flash.0: Found an alias at 0x400000 for the chip at 0x0
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.1.
Silicon revision: 0
Address sensitive unlock: Required
Erase Suspend: Read/write
Block protection: 4 sectors per group
Temporary block unprotect: Supported
Block protect/unprotect scheme: 4
Number of simultaneous operations: 0
Burst mode: Not supported
Page mode: Not supported
Vpp Supply Minimum Program/Erase Voltage: 9.5 V
Vpp Supply Maximum Program/Erase Voltage: 10.5 V
Top/Bottom Boot Block: Bottom boot
number of CFI chips: 1
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Using physmap partition information
Creating 6 MTD partitions on "physmap-flash.0":
0x000000000000-0x000000030000 : "u-boot"
0x000000030000-0x000000040000 : "devdata"
0x000000040000-0x000000050000 : "devconf"
0x000000050000-0x000000120000 : "kernel"
0x000000120000-0x000000400000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=260000, len=1A0000
0x000000260000-0x000000400000 : "rootfs_data"
0x000000050000-0x000000400000 : "firmware"
ramips_eth: loaded
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <[email protected]>
All bugs added by David S. Miller <[email protected]>
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
lib80211_crypt: registered algorithm 'WEP'
lib80211_crypt: registered algorithm 'CCMP'
lib80211_crypt: registered algorithm 'TKIP'
VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
Freeing unused kernel memory: 152k freed
Registered led device: mofi3500-3gn:green:usb
Registered led device: mofi3500-3gn:green:3g
Registered led device: mofi3500-3gn:green:status
Registered led device: mofi3500-3gn:green:wps
JFFS2 notice: (303) jffs2_build_xattr_subsystem: complete building xattr
subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 3 of xref (0 dead, 2
orphan) found.
Compat-wireless backport release: compat-wireless-2011-06-23
Backport based on wireless-testing.git master-2011-06-22
cfg80211: Calling CRDA to update world regulatory domain
device eth0.1 entered promiscuous mode
device eth0 entered promiscuous mode
br-lan: port 1(eth0.1) entering forwarding state
br-lan: port 1(eth0.1) entering forwarding state
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain,
max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Registered led device: rt2800pci-phy0::radio
Registered led device: rt2800pci-phy0::assoc
Registered led device: rt2800pci-phy0::quality
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (470 buckets, 1880 max)
ramips-wdt: timeout value 60 must be 0 < timeout < 40
Regards,
Andrew.
_______________________________________________
openwrt-devel mailing list
[email protected]
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
