Hi all, could you help me with my current issue that my dual-flash AP
can not initialized the second flash correctly.
below is my boot log:
below is my boot log :
U-boot DB120
DRAM:
sri
Wasp 1.2
wasp_ddr_initial_config(255): (32bit) ddr2 init
Setting 0xb8116290 to 0x38702d0f
128 MB
cpu_pll_cfg: 0x21354
cpu_pll_dither: 0x3c153f
CFG_PLL_FREQ: 0x1f
CFG_HZ : 266500000
CPU Clock: 533MHz DDR Clock: 400MHz
Top of RAM usable for U-Boot at: 88000000
Reserving 230k for U-Boot at: 87fc4000
Reserving 192k for malloc() at: 87f94000
Reserving 44 Bytes for Board Info at: 87f93fd4
Reserving 44 Bytes for Global Data at: 87f93fa8
Reserving 128k for boot params() at: 87f73fa8
Stack Pointer at: 87f73f88
Now running in RAM - U-Boot at: 87fc4000
manufacturerId 0xc2, deviceId0 0x20, deviceId1 0x18
flash size 16MB, sector count = 256
flash-2 size 16MB, sector count = 256
Flash: 16 MB
pci_init_board: PCIe PLL not set for 40MHz refclk
BOARD IS NOT CALIBRATED!!!
[eapsw_watchdog::status] warm start
[eapsw_watchdog::status] boot normally
[eapsw_watchdog::status] autoswitch enabled=On , times=None
Current Image was A
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
No valid address in Flash. Using fixed address
wasp reset mask:10c03300
WASP ----> F1 PHY *
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
F1Phy reg init
ATHR_AUTONEG_ADVERT:1DE1
ATHR_1000BASET_CONTROL:200
ATHR_PHY_CONTROL:3100
ATHRSF1_PHY: Port 5, Neg Success
ATHRSF1_PHY: unit 0 phy addr 5 eth0 up
eth0
Hit any key to stop autoboot: 0
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728
Starting kernel ...
[ 0.000000] Linux version 3.7.4 (banglang@Ubuntu-Linux) (gcc version 4.6.4
20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #831 Fri Aug 30 11:07:44 HKT
2013
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 2
[ 0.000000] Clocks: CPU:532.500MHz, DDR:400.000MHz, AHB:200.000MHz,
Ref:40.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32
bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
pages: 32512
[ 0.000000] Kernel command line: board=DB120 console=ttyS0,115200
mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,6336k(rootfsA),1408k(kernelA),64k(nvramA),64k(artA)ro;spi0.1:320k(reserved),6336k(rootfs),1408k(kernel),64k(nvram),64k(art)ro,7744k@0x50000(firmware)
rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 121708k/131072k available (2199k kernel code, 9364k
reserved, 617k data, 4796k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1,
Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.100000] MIPS: machine is Atheros DB120 reference board
[ 0.110000] registering PCI controller with io_map_base unset
[ 0.320000] DB120 :Tymon reg_show show 0x1805002c:0xa000000
[ 0.320000] DB120 :IMAGE - KERNEL AAAAAAAAAAA
[ 0.320000] DB120 :mac_init accton mac address init:70-72-cf-88-ff-20
[ 0.330000] bio: create slab <bio-0> at 0
[ 0.340000] PCI host bridge to bus 0000:00
[ 0.340000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.350000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.350000] pci_bus 0000:00: No busn resource found for root bus, will use
[bus 00-ff]
[ 0.360000] pci 0000:00:00.0: invalid calibration data
[ 0.360000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff
64bit]
[ 0.370000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff
pref]
[ 0.370000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.380000] Switching to clocksource MIPS
[ 0.380000] NET: Registered protocol family 2
[ 0.390000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.390000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.400000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.400000] TCP: reno registered
[ 0.410000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.410000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.420000] NET: Registered protocol family 1
[ 7.200000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 7.200000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 7.210000] msgmni has been set to 237
[ 7.220000] io scheduler noop registered
[ 7.220000] io scheduler deadline registered (default)
[ 7.230000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 7.250000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 7.260000] console [ttyS0] enabled, bootconsole disabled
[ 7.260000] console [ttyS0] enabled, bootconsole disabled
[ 7.270000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 7.280000] m25p80 spi0.0: found mx25l12805d, expected m25p80
[ 7.290000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 7.290000] 6 cmdlinepart partitions found on MTD device spi0.0
[ 7.300000] Creating 6 MTD partitions on "spi0.0":
[ 7.300000] 0x000000000000-0x000000040000 : "u-boot"
[ 7.310000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 7.320000] 0x000000050000-0x000000680000 : "rootfsA"
[ 7.320000] 0x000000680000-0x0000007e0000 : "kernelA"
[ 7.330000] 0x0000007e0000-0x0000007f0000 : "nvramA"
[ 7.340000] 0x0000007f0000-0x000000800000 : "artA"
[ 7.340000] m25p80 spi0.1: found mr25h256, expected m25p80
[ 7.350000] m25p80 spi0.1: mr25h256 (32 Kbytes)
[ 7.360000] mtd: spi0.1: partitioning exceeds flash size, truncating
[ 7.360000] mtd: spi0.1: partitioning exceeds flash size, truncating
[ 7.370000] mtd: spi0.1: partitioning exceeds flash size, truncating
[ 7.370000] mtd: spi0.1: partitioning exceeds flash size, truncating
[ 7.380000] mtd: spi0.1: partitioning exceeds flash size, truncating
[ 7.390000] mtd: spi0.1: partitioning exceeds flash size, truncating
[ 7.390000] 6 cmdlinepart partitions found on MTD device spi0.1
[ 7.400000] Creating 6 MTD partitions on "spi0.1":
[ 7.400000] 0x000000000000-0x000000008000 : "reserved"
[ 7.410000] 0x000000008000-0x000000008000 : "rootfs"
[ 7.420000] mtd: partition "rootfs" is out of reach -- disabled
[ 7.420000] mtd: partition "rootfs" set to be root filesystem
[ 7.430000] split_squashfs: no squashfs found in "spi0.1"
[ 7.440000] 0x000000008000-0x000000008000 : "kernel"
[ 7.440000] mtd: partition "kernel" is out of reach -- disabled
[ 7.450000] 0x000000008000-0x000000008000 : "nvram"
[ 7.450000] mtd: partition "nvram" is out of reach -- disabled
[ 7.460000] 0x000000008000-0x000000008000 : "art"
[ 7.470000] mtd: partition "art" is out of reach -- disabled
[ 7.470000] 0x000000050000-0x000000008000 : "firmware"
[ 7.480000] mtd: partition "firmware" is out of reach -- disabled
[ 7.490000] ATHR_GMAC: Length per segment 1536
[ 7.490000] ATHR_GMAC: fifo cfg 3 01f00140
[ 7.500000] ATHR_GMAC: RX TASKLET - Pkts per Intr:100
[ 7.500000] ATHR_GMAC: Mac address for unit:0 addr:0x8795db00
[ 7.510000] ATHR_GMAC: 70:72:cf:88:ff:20
[ 8.060000] ATHR_GMAC: Max segments per packet : 1
[ 8.070000] ATHR_GMAC: Max tx descriptor count : 128
[ 8.070000] ATHR_GMAC: Max rx descriptor count : 192
[ 8.080000] ATHR_GMAC: Mac capability flags : 2380
[ 8.090000] TCP: cubic registered
[ 8.090000] NET: Registered protocol family 17
[ 8.090000] 8021q: 802.1Q VLAN Support v1.8
[ 8.100000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 8.130000] Freeing unused kernel memory: 4796k freed
[ 8.840000] athr_gmac_ring_alloc Allocated 2048 at 0x8781b000
[ 8.840000] athr_gmac_ring_alloc Allocated 3072 at 0x87809000
[ 9.150000] WASP ----> F1e PHY
[ 9.150000] Setting Drop CRC Errors, Pause Frames and Length Error frames
[ 9.160000] Setting PHY...
[ 9.160000] ATHR_AUTONEG_ADVERT:DE1
[ 9.160000] ATHR_1000BASET_CONTROL:200
[ 9.170000] ATHR_PHY_CONTROL:1000
[ 9.170000] ATHRSF1_PHY: Port 5, Neg Success
[ 9.180000] ATHRSF1_PHY: unit 0 phy addr 5
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[ 12.380000] athr_gmac_ring_free Freeing at 0x8781b000
[ 12.380000] athr_gmac_ring_free Freeing at 0x87809000
- init -
[ 12.720000] Compat-drivers backport release: compat-drivers-2013-01-08-3
[ 12.720000] Backport based on wireless-testing.git master-2013-01-07
[ 12.730000] compat.git: wireless-testing.git
[ 12.760000] cfg80211: Calling CRDA to update world regulatory domain
[ 12.760000] cfg80211: World regulatory domain updated:
[ 12.770000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp)
[ 12.780000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 12.780000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi,
2000 mBm)
[ 12.790000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi,
2000 mBm)
[ 12.800000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 12.810000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 12.890000] NET: Registered protocol family 10
[ 13.010000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND
128MiB 3,3V 8-bit), page size: 2048, OOB size: 64
[ 13.020000] Scanning device for bad blocks
[ 13.080000] Bad eraseblock 527 at 0x0000041e0000
[ 13.110000] Bad eraseblock 756 at 0x000005e80000
[ 13.220000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
[ 13.230000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 13.330000] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
[ 13.330000] cfg80211: Calling CRDA for country: US
[ 13.340000] cfg80211: Regulatory domain changed to country: US
[ 13.340000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp)
[ 13.350000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi,
2700 mBm)
[ 13.360000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi,
1700 mBm)
[ 13.370000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 13.380000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 13.380000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 13.390000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi,
3000 mBm)
[ 13.450000] PPP generic driver version 2.4.2
[ 13.520000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 13.620000] NET: Registered protocol family 24
[ 13.640000] nf_conntrack version 0.5.0 (1976 buckets, 7904 max)
[ 13.970000] xt_time: kernel timezone is -0000
[ 14.220000] u32 classifier
[ 14.220000] Performance counters on
[ 14.220000] input device check on
[ 14.230000] Actions configured
[ 14.250000] Mirror/redirect action on
Any suggestion will be appreciated.
The part of my source code is :
static void __init db120_setup(void)
{
u8 *art = (u8 *) KSEG1ADDR(0x1fff0000);
...........
//ath79_register_m25p80(NULL);
ath79_register_m25p80_multi(&db120_flash_data);
xxxx
.........
}_______________________________________________
openwrt-devel mailing list
[email protected]
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
