would you mind to use a single flash this time. In your log, the second flash's hardware id can't be regnized.
"．浪花o" <[email protected]>写到： >Anyone here to help? > > > > >------------------ 原始邮件 ------------------ >发件人: "．浪花o"; >发送时间: 2013年8月30日(星期五) 下午3:14 >收件人: "openwrt-devel"; >主题: [OpenWrt-Devel] Porting my dual-flash wireless AP,but the senond >flash can not initialized correctly. > > > >Hi all, could you help me with my current issue that my >dual-flash AP can not initialized the second flash correctly. > > > below is my boot log: > > > >below is my boot log : > >U-boot DB120 >DRAM: >sri >Wasp 1.2 >wasp_ddr_initial_config(255): (32bit) ddr2 init >Setting 0xb8116290 to 0x38702d0f >128 MB > >cpu_pll_cfg: 0x21354 >cpu_pll_dither: 0x3c153f >CFG_PLL_FREQ: 0x1f >CFG_HZ : 266500000 > >CPU Clock: 533MHz DDR Clock: 400MHz > >Top of RAM usable for U-Boot at: 88000000 >Reserving 230k for U-Boot at: 87fc4000 >Reserving 192k for malloc() at: 87f94000 >Reserving 44 Bytes for Board Info at: 87f93fd4 >Reserving 44 Bytes for Global Data at: 87f93fa8 >Reserving 128k for boot params() at: 87f73fa8 >Stack Pointer at: 87f73f88 >Now running in RAM - U-Boot at: 87fc4000 >manufacturerId 0xc2, deviceId0 0x20, deviceId1 0x18 >flash size 16MB, sector count = 256 >flash-2 size 16MB, sector count = 256 >Flash: 16 MB >pci_init_board: PCIe PLL not set for 40MHz refclk >BOARD IS NOT CALIBRATED!!! >[eapsw_watchdog::status] warm start >[eapsw_watchdog::status] boot normally >[eapsw_watchdog::status] autoswitch enabled=On , times=None >Current Image was A >In: serial >Out: serial >Err: serial >Net: ag934x_enet_initialize... >No valid address in Flash. Using fixed address >wasp reset mask:10c03300 >WASP ----> F1 PHY * >: cfg1 0x80000000 cfg2 0x7114 >eth0: 00:03:7f:09:0b:ad >F1Phy reg init >ATHR_AUTONEG_ADVERT:1DE1 >ATHR_1000BASET_CONTROL:200 >ATHR_PHY_CONTROL:3100 >ATHRSF1_PHY: Port 5, Neg Success >ATHRSF1_PHY: unit 0 phy addr 5 eth0 up >eth0 >Hit any key to stop autoboot: 0 > > >## Transferring control to Linux (at address 80060000) ... >## Giving linux memsize in bytes, 134217728 > >Starting kernel ... > >[ 0.000000] Linux version 3.7.4 (banglang@Ubuntu-Linux) (gcc version >4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #831 Fri Aug 30 >11:07:44 HKT 2013 >[ 0.000000] bootconsole [early0] enabled >[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc) >[ 0.000000] SoC: Atheros AR9344 rev 2 >[ 0.000000] Clocks: CPU:532.500MHz, DDR:400.000MHz, AHB:200.000MHz, >Ref:40.000MHz >[ 0.000000] Determined physical RAM map: >[ 0.000000] memory: 08000000 @ 00000000 (usable) >[ 0.000000] Initrd not found or empty - disabling initrd >[ 0.000000] Zone ranges: >[ 0.000000] Normal [mem 0x00000000-0x07ffffff] >[ 0.000000] Movable zone start for each node >[ 0.000000] Early memory node ranges >[ 0.000000] node 0: [mem 0x00000000-0x07ffffff] >[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 >bytes. >[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, >linesize 32 bytes >[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. >Total pages: 32512 >[ 0.000000] Kernel command line: board=DB120 console=ttyS0,115200 >mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,6336k(rootfsA),1408k(kernelA),64k(nvramA),64k(artA)ro;spi0.1:320k(reserved),6336k(rootfs),1408k(kernel),64k(nvram),64k(art)ro,7744k@0x50000(firmware) >rootfstype=squashfs,jffs2 noinitrd >[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) >[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 >bytes) >[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 >bytes) >[ 0.000000] __ex_table already sorted, skipping sort >[ 0.000000] Writing ErrCtl register=00000000 >[ 0.000000] Readback ErrCtl register=00000000 >[ 0.000000] Memory: 121708k/131072k available (2199k kernel code, >9364k reserved, 617k data, 4796k init, 0k highmem) >[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, >CPUs=1, Nodes=1 >[ 0.000000] NR_IRQS:51 >[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104) >[ 0.080000] pid_max: default: 32768 minimum: 301 >[ 0.080000] Mount-cache hash table entries: 512 >[ 0.090000] NET: Registered protocol family 16 >[ 0.100000] MIPS: machine is Atheros DB120 reference board >[ 0.110000] registering PCI controller with io_map_base unset >[ 0.320000] DB120 :Tymon reg_show show 0x1805002c:0xa000000 >[ 0.320000] DB120 :IMAGE - KERNEL AAAAAAAAAAA >[ 0.320000] DB120 :mac_init accton mac address >init:70-72-cf-88-ff-20 >[ 0.330000] bio: create slab <bio-0> at 0 >[ 0.340000] PCI host bridge to bus 0000:00 >[ 0.340000] pci_bus 0000:00: root bus resource [mem >0x10000000-0x13ffffff] >[ 0.350000] pci_bus 0000:00: root bus resource [io 0x0000] >[ 0.350000] pci_bus 0000:00: No busn resource found for root bus, >will use [bus 00-ff] >[ 0.360000] pci 0000:00:00.0: invalid calibration data >[ 0.360000] pci 0000:00:00.0: BAR 0: assigned [mem >0x10000000-0x1001ffff 64bit] >[ 0.370000] pci 0000:00:00.0: BAR 6: assigned [mem >0x10020000-0x1002ffff pref] >[ 0.370000] pci 0000:00:00.0: using irq 40 for pin 1 >[ 0.380000] Switching to clocksource MIPS >[ 0.380000] NET: Registered protocol family 2 >[ 0.390000] TCP established hash table entries: 4096 (order: 3, >32768 bytes) >[ 0.390000] TCP bind hash table entries: 4096 (order: 2, 16384 >bytes) >[ 0.400000] TCP: Hash tables configured (established 4096 bind 4096) >[ 0.400000] TCP: reno registered >[ 0.410000] UDP hash table entries: 256 (order: 0, 4096 bytes) >[ 0.410000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) >[ 0.420000] NET: Registered protocol family 1 >[ 7.200000] squashfs: version 4.0 (2009/01/31) Phillip Lougher >[ 7.200000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) >(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. >[ 7.210000] msgmni has been set to 237 >[ 7.220000] io scheduler noop registered >[ 7.220000] io scheduler deadline registered (default) >[ 7.230000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled >[ 7.250000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a >16550A >[ 7.260000] console [ttyS0] enabled, bootconsole disabled >[ 7.260000] console [ttyS0] enabled, bootconsole disabled >[ 7.270000] ath79-spi ath79-spi: master is unqueued, this is >deprecated >[ 7.280000] m25p80 spi0.0: found mx25l12805d, expected m25p80 >[ 7.290000] m25p80 spi0.0: mx25l12805d (16384 Kbytes) >[ 7.290000] 6 cmdlinepart partitions found on MTD device spi0.0 >[ 7.300000] Creating 6 MTD partitions on "spi0.0": >[ 7.300000] 0x000000000000-0x000000040000 : "u-boot" >[ 7.310000] 0x000000040000-0x000000050000 : "u-boot-env" >[ 7.320000] 0x000000050000-0x000000680000 : "rootfsA" >[ 7.320000] 0x000000680000-0x0000007e0000 : "kernelA" >[ 7.330000] 0x0000007e0000-0x0000007f0000 : "nvramA" >[ 7.340000] 0x0000007f0000-0x000000800000 : "artA" >[ 7.340000] m25p80 spi0.1: found mr25h256, expected m25p80 >[ 7.350000] m25p80 spi0.1: mr25h256 (32 Kbytes) >[ 7.360000] mtd: spi0.1: partitioning exceeds flash size, truncating >[ 7.360000] mtd: spi0.1: partitioning exceeds flash size, truncating >[ 7.370000] mtd: spi0.1: partitioning exceeds flash size, truncating >[ 7.370000] mtd: spi0.1: partitioning exceeds flash size, truncating >[ 7.380000] mtd: spi0.1: partitioning exceeds flash size, truncating >[ 7.390000] mtd: spi0.1: partitioning exceeds flash size, truncating >[ 7.390000] 6 cmdlinepart partitions found on MTD device spi0.1 >[ 7.400000] Creating 6 MTD partitions on "spi0.1": >[ 7.400000] 0x000000000000-0x000000008000 : "reserved" >[ 7.410000] 0x000000008000-0x000000008000 : "rootfs" >[ 7.420000] mtd: partition "rootfs" is out of reach -- disabled >[ 7.420000] mtd: partition "rootfs" set to be root filesystem >[ 7.430000] split_squashfs: no squashfs found in "spi0.1" >[ 7.440000] 0x000000008000-0x000000008000 : "kernel" >[ 7.440000] mtd: partition "kernel" is out of reach -- disabled >[ 7.450000] 0x000000008000-0x000000008000 : "nvram" >[ 7.450000] mtd: partition "nvram" is out of reach -- disabled >[ 7.460000] 0x000000008000-0x000000008000 : "art" >[ 7.470000] mtd: partition "art" is out of reach -- disabled >[ 7.470000] 0x000000050000-0x000000008000 : "firmware" >[ 7.480000] mtd: partition "firmware" is out of reach -- disabled >[ 7.490000] ATHR_GMAC: Length per segment 1536 >[ 7.490000] ATHR_GMAC: fifo cfg 3 01f00140 >[ 7.500000] ATHR_GMAC: RX TASKLET - Pkts per Intr:100 >[ 7.500000] ATHR_GMAC: Mac address for unit:0 addr:0x8795db00 >[ 7.510000] ATHR_GMAC: 70:72:cf:88:ff:20 >[ 8.060000] ATHR_GMAC: Max segments per packet : 1 >[ 8.070000] ATHR_GMAC: Max tx descriptor count : 128 >[ 8.070000] ATHR_GMAC: Max rx descriptor count : 192 >[ 8.080000] ATHR_GMAC: Mac capability flags : 2380 >[ 8.090000] TCP: cubic registered >[ 8.090000] NET: Registered protocol family 17 >[ 8.090000] 8021q: 802.1Q VLAN Support v1.8 >[ 8.100000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) >[ 8.130000] Freeing unused kernel memory: 4796k freed >[ 8.840000] athr_gmac_ring_alloc Allocated 2048 at 0x8781b000 >[ 8.840000] athr_gmac_ring_alloc Allocated 3072 at 0x87809000 >[ 9.150000] WASP ----> F1e PHY >[ 9.150000] Setting Drop CRC Errors, Pause Frames and Length Error >frames >[ 9.160000] Setting PHY... >[ 9.160000] ATHR_AUTONEG_ADVERT:DE1 >[ 9.160000] ATHR_1000BASET_CONTROL:200 >[ 9.170000] ATHR_PHY_CONTROL:1000 >[ 9.170000] ATHRSF1_PHY: Port 5, Neg Success >[ 9.180000] ATHRSF1_PHY: unit 0 phy addr 5 >- preinit - >Press the [f] key and hit [enter] to enter failsafe mode >- regular preinit - >[ 12.380000] athr_gmac_ring_free Freeing at 0x8781b000 >[ 12.380000] athr_gmac_ring_free Freeing at 0x87809000 >- init - >[ 12.720000] Compat-drivers backport release: >compat-drivers-2013-01-08-3 >[ 12.720000] Backport based on wireless-testing.git master-2013-01-07 >[ 12.730000] compat.git: wireless-testing.git >[ 12.760000] cfg80211: Calling CRDA to update world regulatory domain >[ 12.760000] cfg80211: World regulatory domain updated: >[ 12.770000] cfg80211: (start_freq - end_freq @ bandwidth), >(max_antenna_gain, max_eirp) >[ 12.780000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), >(300 mBi, 2000 mBm) >[ 12.780000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), >(300 mBi, 2000 mBm) >[ 12.790000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), >(300 mBi, 2000 mBm) >[ 12.800000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), >(300 mBi, 2000 mBm) >[ 12.810000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), >(300 mBi, 2000 mBm) >[ 12.890000] NET: Registered protocol family 10 >[ 13.010000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix >NAND 128MiB 3,3V 8-bit), page size: 2048, OOB size: 64 >[ 13.020000] Scanning device for bad blocks >[ 13.080000] Bad eraseblock 527 at 0x0000041e0000 >[ 13.110000] Bad eraseblock 756 at 0x000005e80000 >[ 13.220000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, >irq=47 >[ 13.230000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) >[ 13.330000] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, >irq=40 >[ 13.330000] cfg80211: Calling CRDA for country: US >[ 13.340000] cfg80211: Regulatory domain changed to country: US >[ 13.340000] cfg80211: (start_freq - end_freq @ bandwidth), >(max_antenna_gain, max_eirp) >[ 13.350000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), >(300 mBi, 2700 mBm) >[ 13.360000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), >(300 mBi, 1700 mBm) >[ 13.370000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), >(300 mBi, 2000 mBm) >[ 13.380000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), >(300 mBi, 2000 mBm) >[ 13.380000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), >(300 mBi, 2000 mBm) >[ 13.390000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), >(300 mBi, 3000 mBm) >[ 13.450000] PPP generic driver version 2.4.2 >[ 13.520000] ip_tables: (C) 2000-2006 Netfilter Core Team >[ 13.620000] NET: Registered protocol family 24 >[ 13.640000] nf_conntrack version 0.5.0 (1976 buckets, 7904 max) >[ 13.970000] xt_time: kernel timezone is -0000 >[ 14.220000] u32 classifier >[ 14.220000] Performance counters on >[ 14.220000] input device check on >[ 14.230000] Actions configured >[ 14.250000] Mirror/redirect action on > > > > > > > >Any suggestion will be appreciated. > > > > > > > > > > >The part of my source code is : > >static void __init db120_setup(void) > >{ > > u8 *art = (u8 *) KSEG1ADDR(0x1fff0000); > >........... > > //ath79_register_m25p80(NULL); > > ath79_register_m25p80_multi(&db120_flash_data); > > > > xxxx > >......... > >} > >------------------------------------------------------------------------ > >_______________________________________________ >openwrt-devel mailing list >[email protected] >https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel -- Randy _______________________________________________ openwrt-devel mailing list [email protected] https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
