This adds kernel support support for Sagemcom F@st 2704 wireless ADSL router. It's a BCM6328-based 802.11n wireless router with USB port and ADSL2+ modem equipped with 64 MiB RAM and 8 MiB flash.
Signed-off-by: Marcin Jurkowski <[email protected]> --- .../brcm63xx/patches-3.10/803-board_fast2704.patch | 133 +++++++++++++++++++++ 1 file changed, 133 insertions(+) create mode 100644 target/linux/brcm63xx/patches-3.10/803-board_fast2704.patch diff --git a/target/linux/brcm63xx/patches-3.10/803-board_fast2704.patch b/target/linux/brcm63xx/patches-3.10/803-board_fast2704.patch new file mode 100644 index 0000000..ba03fa8 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.10/803-board_fast2704.patch @@ -0,0 +1,133 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -1501,6 +1501,122 @@ static struct board_info __initdata boar + }, + }; + ++static struct board_info __initdata board_FAST2704V2 = { ++ .name = "F@ST2704V2", ++ .expected_cpu_id = 0x6328, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ .has_ohci0 = 1, ++ .has_ehci0 = 1, ++ .has_usbd = 1, ++ ++ .has_enetsw = 1, ++ ++ .enetsw = { ++ .used_ports = { ++ [0] = { ++ .used = 1, ++ .phy_id = 1, ++ .name = "Port 1", ++ }, ++ [1] = { ++ .used = 1, ++ .phy_id = 2, ++ .name = "Port 2", ++ }, ++ [2] = { ++ .used = 1, ++ .phy_id = 3, ++ .name = "Port 3", ++ }, ++ [3] = { ++ .used = 1, ++ .phy_id = 4, ++ .name = "Port 4", ++ }, ++ }, ++ }, ++ ++ .leds = { ++ /* front LEDs */ ++ { ++ .name = "F@ST2704V2:green:power", ++ .gpio = 4, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "F@ST2704V2:red:power", ++ .gpio = 5, ++ .active_low = 1, ++ }, ++ { ++ .name = "F@ST2704V2:red:inet", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "F@ST2704V2:green:dsl", ++ .gpio = 3, ++ .active_low = 1, ++ }, ++ { ++ .name = "F@ST2704V2:green:inet", ++ .gpio = 11, ++ .active_low = 1, ++ }, ++ { ++ .name = "F@ST2704V2:green:usb", ++ .gpio = 1, ++ .active_low = 1, ++ }, ++ ++ /* side button LEDs */ ++ { ++ .name = "F@ST2704V2:green:wps", ++ .gpio = 10, ++ .active_low = 1, ++ }, ++ ++ /* FIXME: can't control gpio0 line in "out" state, needs further investigation */ ++ /* ++ { ++ .name = "F@ST2704V2:green:rfkill", ++ .gpio = 0, ++ .active_low = 1, ++ }, ++ */ ++ ++ }, ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 23, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "wps", ++ .gpio = 24, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_WPS_BUTTON, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "rfkill", ++ .gpio = 15, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RFKILL, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; ++ + static struct board_info __initdata board_rta1025w_16 = { + .name = "RTA1025W_16", + .expected_cpu_id = 0x6348, +@@ -4042,6 +4158,7 @@ static const struct board_info __initcon + &board_963281TAN, + &board_963281T_TEF, + &board_dsl_274xb_f1, ++ &board_FAST2704V2, + #endif + #ifdef CONFIG_BCM63XX_CPU_6338 + &board_96338gw, -- 1.8.1.5 _______________________________________________ openwrt-devel mailing list [email protected] https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
