I thought you said a couple posts ago that you were able to configure it through
the GUI to work the way you wanted it to, you were just wanting to make
something the default.
So do you have it working or not?
If you have it working, it should keep working after a reboot. What are you
meaning when you say that you want to change the default?
Are you meaning that you want to create an image that will behave this way when
you do a factory reset (or when you first flash it)? If so, then you need to
take your working config and make it part of your image via the files/
mechansim.
If you are meaning something else, I'm still not understanding what you are
trying to do.
David Lang
On Tue, 11 Aug 2015, John kerry wrote:
Date: Tue, 11 Aug 2015 21:20:58 +0800
From: John kerry <[email protected]>
To: David Lang <[email protected]>
Cc: Alex Weedy <[email protected]>,
OpenWrt Development List <[email protected]>
Subject: Re: [OpenWrt-Devel] Fwd: "3-address Wi-Fi bridging" (was: Multiple
Wi-Fi client/AP interfaces on one radio)
Hi,
How to config wireless config file for repeater mode. I am not able to
config.
On Tue, Aug 11, 2015 at 5:34 PM, John kerry <[email protected]> wrote:
When i load firmware the wireless config will be like below:
config wifi-device 'wifi0'
option type 'qcawifi'
option macaddr '00:26:75:bd:37:24'
option hwmode '11ng'
option txpower '16'
option htmode 'HT20'
option disabled '0'
option channel '1'
config wifi-iface
option device 'wifi0'
option mode 'ap'
option ssid 'Test_ap'
option network 'lan'
option encryption 'psk2'
option key 'Test_ap'
option wds '1'
so it works as Access point, i can connect to it any devices. When i scan
it shows me list of devices then connect to anyone. then the wireless
config will becomes like below:
config wifi-device 'wifi0'
option type 'qcawifi'
option macaddr '00:26:75:bd:37:24'
option hwmode '11ng'
option txpower '16'
option htmode 'HT20'
option disabled '0'
option channel '1'
config wifi-iface
option network 'wwan'
option ssid 'D-link-Router'
option encryption 'psk2'
option device 'wifi0'
option mode 'sta'
option key '0010069039'
option wds '1'
Then i add one more ap mode so wireless config becomes,
config wifi-device 'wifi0'
option type 'qcawifi'
option macaddr '00:26:75:bd:37:24'
option hwmode '11ng'
option txpower '16'
option htmode 'HT20'
option disabled '0'
option channel '1'
config wifi-iface
option network 'wwan'
option ssid 'D-link-Router'
option encryption 'psk2'
option device 'wifi0'
option mode 'sta'
option key '0010069039'
option wds '1'
config wifi-iface
option device 'wifi0'
option mode 'ap'
option ssid 'Test_ap'
option network 'lan'
option encryption 'psk2'
option key 'Test_ap'
option wds '1'
This i added manually one ap mode.
So if i copy this config file, build and load this firmware, its load what
it was there so it shows one client which i was connected last time and one
AP which i added.
But now i cannot scan anymore and connect to new router instead of old
client.
This is the problem i am facing.
Basically i need to configure the wireless file for repeater mode.
So after connecting to another router this SSID still should be there and
other device can connect to it.
On Tue, Aug 11, 2015 at 4:30 PM, David Lang <[email protected]> wrote:
you have a working config
but you want to do something by default
what you want to do is different at different times.
what is it that you want to be the default? when do you want this default
to apply? This isn't clear.
David Lang
On Tue, 11 Aug 2015, John kerry wrote:
Date: Tue, 11 Aug 2015 15:51:38 +0800
From: John kerry <[email protected]>
To: David Lang <[email protected]>
Cc: Alex Weedy <[email protected]>,
OpenWrt Development List <[email protected]>
Subject: Re: [OpenWrt-Devel] Fwd: "3-address Wi-Fi bridging" (was:
Multiple
Wi-Fi client/AP interfaces on one radio)
Yes,
i can copy the config and build with this configuration,
for example now i have connected to some router, another time we can
connect to any router. So how i can fix the settings by default.
On Tue, Aug 11, 2015 at 12:45 AM, David Lang <[email protected]> wrote:
On Mon, 10 Aug 2015, John kerry wrote:
I followed the same steps and its working too. But this i want in
wireless
config file, Because i dont want every time to add using GUI. So When i
connect to another router also, no need to add one more. I mean to say
it
should be in default wireless config file.
what do you mean by "default wireless config file"
Once you have set it from the GUI, it is in the config files. The next
time you boot it will use that config.
If you mean that you want it in the factory default config (for when you
first flash the router or do a factory reset), then take the
/etc/config/wireless and /etc/config/network files and add them to your
build under /files
David Lang
On Mon, Aug 10, 2015 at 6:18 PM, David Lang <[email protected]> wrote:
On Mon, 10 Aug 2015, John kerry wrote:
Date: Mon, 10 Aug 2015 18:10:14 +0800
From: John kerry <[email protected]>
To: Alex Weedy <[email protected]>,
OpenWrt Development List <[email protected]>
Subject: [OpenWrt-Devel] Fwd: "3-address Wi-Fi bridging" (was:
Multiple
Wi-Fi
client/AP interfaces on one radio)
Firstly i configure wireless config as below:
config wifi-device 'wifi0'
option type 'qcawifi'
option macaddr '00:01:11:00:01:00'
option hwmode '11ng'
option txpower '17'
option htmode 'HT20'
option disabled '0'
option channel '1'
config wifi-iface
option device 'wifi0'
option mode 'ap'
option ssid 'Testing_ap'
option network 'lan'
option encryption 'psk2'
option key 'Testing_ap'
so its SSID was showing and able to connect any device to it.
Then i scan the device and connect to one of it. While joining the
network
i selected Client(WDS) then the wireless config becomes like below:
why don't you try following the steps in the video that you posted.
first connect as a client, then add an additional interface and make
the
second interface the AP for things to connect to.
the order may make a difference.
David Lang
config wifi-device 'wifi0'
option type 'qcawifi'
option macaddr '00:01:11:00:01:00'
option hwmode '11ng'
option txpower '17'
option htmode 'HT20'
option disabled '0'
option channel '1'
config wifi-iface
option network 'wwan'
option ssid 'D_Link_Router'
option encryption 'psk2'
option device 'wifi0'
option mode 'sta'
option key 'Dlink_Router'
option wds '1'
Then i added one as shown in the video. Now its connected to router
also
and this add one also showing so i can connect to this also.
But i am not getting how to keep this in default wireless config.
Because every time we cant add one to configure like this. It should
be
like default should be in ap mode so any device we can connect, if
its
connected to another router also that SSID still should be visible
and
able
to connect to this.
On Mon, Aug 10, 2015 at 2:57 PM, John kerry <[email protected]>
wrote:
When i try to configure based on video, its shows 2 one as client
another
one as Master but i am not able to enable it . I mean to say wireless
becomes disable. If i enable it using GUI also its not happening.
On Mon, Aug 10, 2015 at 2:55 PM, David Lang <[email protected]> wrote:
What happens when you try to follow the video?
Based on your comments, i'm guessing that things don't work when
you
try
and configure the second network and have it with a different SSID
than
the
first network that you put in client mode.
Is this correct?
David Lang
On Mon, 10 Aug 2015, John kerry wrote:
Yes, When i am connecting to Another router its changed to Client
mode.
Can i configure this in repeater mode like its shows in below link:
https://www.youtube.com/watch?v=3rbsh2zxPnk
_______________________________________________
openwrt-devel mailing list
[email protected]
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
_______________________________________________
openwrt-devel mailing list
[email protected]
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
