#17353: unable to PPPoE connect to wan on HC6361 (trunk - r41954)
-------------------------+-----------------------------------
Reporter: ballgotz | Owner: developers
Type: defect | Status: new
Priority: normal | Milestone:
Component: base system | Version: Barrier Breaker 14.07
Keywords: pppoe |
-------------------------+-----------------------------------
Hi,
Not sure if this is a bug or my misconfiguration, but PPPoE keeps getting
timeout when trying to connect to wan on my HC6361.
{{{
Connect: pppoe-wan <--> /dev/pts/0
LCP: timeout sending Config-Requests
Connection terminated.
Modem hangup
}}}
According to wiki my [http://wiki.openwrt.org/toh/hiwifi/hc6361 HC6361]
should work after r40975.
Whenever I flash my HC6361 with BB RC2, from the nightly snapshots, or
self-built from the newest trunk (r41954), I can't get PPPoE to connect
wan, it'll just keep getting timeout and restart. However, with the exact
same configurations, I can use other people's [https://code.google.com/p
/openwrt-hiwifi/wiki/ProjectIntroduction pre-built firmware] based on
r40975 without any problems.
When sysupgrading to BB RC2 or the newest trunk, the PPPoE will be dead
again. (It'll boot just fine and all else seems to be good, but PPPoE just
won't work.)
I'm not sure if something happened between now and 6/2, but from the svn
changesets I can't notice anything off the top of my head. Perhaps someone
can figure out what's wrong or point me in the right direction?
My /etc/config/network:
{{{
config interface 'loopback'
option ifname 'lo'
option proto 'static'
option ipaddr '127.0.0.1'
option netmask '255.0.0.0'
config globals 'globals'
option ula_prefix 'fd70:3b78:8d30::/48'
config interface 'lan'
option ifname 'eth0.1'
option type 'bridge'
option proto 'static'
option ipaddr '192.168.1.1'
option netmask '255.255.255.0'
option ip6assign '60'
config interface 'wan'
option ifname 'eth0.2'
option proto 'pppoe'
option username 'xxxxxxxx'
option password 'xxxxxxxx'
config interface 'wan6'
option ifname '@wan'
option proto 'dhcpv6'
config switch
option name 'switch0'
option reset '1'
option enable_vlan '1'
config switch_vlan
option device 'switch0'
option vlan '1'
option ports '0t 2 3 4'
config switch_vlan
option device 'switch0'
option vlan '2'
option ports '0t 1'
}}}
My dmesg output:
{{{
[ 0.000000] Linux version 3.10.49 ([email protected]) (gcc version
4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r41954) ) #1 Sun Aug 3 20:27:09 CST
2014
[ 0.000000] MyLoader: sysp=9dbf3185, boardp=4cb3196d, parts=bdc1e69e
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9330 rev 1
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz,
Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 803109b0, node_mem_map
81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32
bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases,
linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 16256
[ 0.000000] Kernel command line: board=HiWiFi-HC6361
console=ttyATH0,115200
mtdparts=spi0.0:64k(u-boot)ro,64k(bdinfo)ro,1280k(kernel),14848k(rootfs),64k(backup)ro,64k(art)ro,16128k@0x20000(firmware)
rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768
bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61272k/65536k available (2239k kernel code, 4264k
reserved, 603k data, 228k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.080000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.100000] MIPS: machine is HiWiFi HC6361
[ 0.550000] bio: create slab <bio-0> at 0
[ 0.560000] Switching to clocksource MIPS
[ 0.560000] NET: Registered protocol family 2
[ 0.570000] TCP established hash table entries: 512 (order: 0, 4096
bytes)
[ 0.570000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.570000] TCP: Hash tables configured (established 512 bind 512)
[ 0.580000] TCP: reno registered
[ 0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.600000] NET: Registered protocol family 1
[ 0.600000] PCI: CLS 0 bytes, default 32
[ 0.620000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.620000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.630000] msgmni has been set to 119
[ 0.640000] io scheduler noop registered
[ 0.640000] io scheduler deadline registered (default)
[ 0.650000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.650000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a
AR933X UART
[ 0.660000] console [ttyATH0] enabled, bootconsole disabled
[ 0.670000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.680000] m25p80 spi0.0: found s25fl129p1, expected m25p80
[ 0.680000] m25p80 spi0.0: s25fl129p1 (16384 Kbytes)
[ 0.690000] 7 cmdlinepart partitions found on MTD device spi0.0
[ 0.690000] Creating 7 MTD partitions on "spi0.0":
[ 0.700000] 0x000000000000-0x000000010000 : "u-boot"
[ 0.710000] 0x000000010000-0x000000020000 : "bdinfo"
[ 0.710000] 0x000000020000-0x000000160000 : "kernel"
[ 0.720000] 0x000000160000-0x000000fe0000 : "rootfs"
[ 0.720000] mtd: device 3 (rootfs) set to be root filesystem
[ 0.730000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.730000] 0x000000330000-0x000000fe0000 : "rootfs_data"
[ 0.740000] 0x000000fe0000-0x000000ff0000 : "backup"
[ 0.750000] 0x000000ff0000-0x000001000000 : "art"
[ 0.750000] 0x000000020000-0x000000fe0000 : "firmware"
[ 0.770000] libphy: ag71xx_mdio: probed
[ 1.320000] ag71xx-mdio.1: Found an AR7240/AR9330 built-in switch
[ 2.360000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 2.910000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04
[uid=004dd041, driver=Generic PHY]
[ 2.920000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 2.930000] TCP: cubic registered
[ 2.930000] NET: Registered protocol family 17
[ 2.930000] 8021q: 802.1Q VLAN Support v1.8
[ 2.950000] VFS: Mounted root (squashfs filesystem) readonly on device
31:3.
[ 2.950000] Freeing unused kernel memory: 228K (80327000 - 80360000)
[ 5.770000] usbcore: registered new interface driver usbfs
[ 5.780000] usbcore: registered new interface driver hub
[ 5.780000] usbcore: registered new device driver usb
[ 5.790000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.800000] ehci-platform: EHCI generic platform driver
[ 5.800000] ehci-platform ehci-platform: EHCI Host Controller
[ 5.810000] ehci-platform ehci-platform: new USB bus registered,
assigned bus number 1
[ 5.820000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 5.840000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 5.840000] hub 1-0:1.0: USB hub found
[ 5.840000] hub 1-0:1.0: 1 port detected
[ 5.850000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.300000] usb 1-1: new high-speed USB device number 2 using ehci-
platform
[ 8.430000] eth0: link up (1000Mbps/Full duplex)
[ 10.730000] jffs2_scan_eraseblock(): End of filesystem marker found at
0x50000
[ 10.740000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 10.740000] jffs2_build_filesystem(): erasing all blocks after the end
marker... done.
[ 40.050000] jffs2: notice: (309) jffs2_build_xattr_subsystem: complete
building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of
xref (0 dead, 0 orphan) found.
[ 45.760000] eth0: link down
[ 47.710000] NET: Registered protocol family 10
[ 47.730000] nf_conntrack version 0.5.0 (960 buckets, 3840 max)
[ 47.740000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 47.760000] Loading modules backported from Linux version
master-2014-05-22-0-gf2032ea
[ 47.760000] Backport generated by backports.git
backports-20140320-37-g5c33da0
[ 47.770000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 47.830000] xt_time: kernel timezone is -0000
[ 47.860000] cfg80211: Calling CRDA to update world regulatory domain
[ 47.860000] cfg80211: World regulatory domain updated:
[ 47.870000] cfg80211: DFS Master region: unset
[ 47.870000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 47.880000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 47.890000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 47.900000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A,
2000 mBm), (N/A)
[ 47.900000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A,
2000 mBm), (N/A)
[ 47.910000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A,
2000 mBm), (0 s)
[ 47.920000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A,
2000 mBm), (0 s)
[ 47.930000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A,
2000 mBm), (N/A)
[ 47.940000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 0 mBm), (N/A)
[ 48.000000] PPP generic driver version 2.4.2
[ 48.020000] NET: Registered protocol family 24
[ 48.080000] ath: EEPROM regdomain: 0x0
[ 48.080000] ath: EEPROM indicates default country code should be used
[ 48.080000] ath: doing EEPROM country->regdmn map search
[ 48.080000] ath: country maps to regdmn code: 0x3a
[ 48.080000] ath: Country alpha2 being used: US
[ 48.080000] ath: Regpair used: 0x3a
[ 48.090000] ieee80211 phy0: Selected rate control algorithm
'minstrel_ht'
[ 48.110000] cfg80211: Calling CRDA for country: US
[ 48.120000] cfg80211: Regulatory domain changed to country: US
[ 48.120000] cfg80211: DFS Master region: FCC
[ 48.120000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 48.130000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A,
3000 mBm), (N/A)
[ 48.140000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A,
1700 mBm), (N/A)
[ 48.150000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A,
2300 mBm), (0 s)
[ 48.160000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A,
3000 mBm), (N/A)
[ 48.170000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 4000 mBm), (N/A)
[ 48.170000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[ 57.580000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 57.590000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 57.590000] device eth0.1 entered promiscuous mode
[ 57.600000] device eth0 entered promiscuous mode
[ 57.600000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 57.650000] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 58.180000] eth0: link up (1000Mbps/Full duplex)
[ 58.180000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 58.220000] br-lan: port 1(eth0.1) entered forwarding state
[ 58.220000] br-lan: port 1(eth0.1) entered forwarding state
[ 58.230000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 58.230000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 58.240000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 58.710000] cfg80211: Calling CRDA for country: TW
[ 58.720000] cfg80211: Regulatory domain changed to country: TW
[ 58.720000] cfg80211: DFS Master region: JP
[ 58.720000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 58.730000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A,
3000 mBm), (N/A)
[ 58.740000] cfg80211: (5270000 KHz - 5330000 KHz @ 40000 KHz), (N/A,
1700 mBm), (0 s)
[ 58.750000] cfg80211: (5490000 KHz - 5590000 KHz @ 80000 KHz), (N/A,
3000 mBm), (0 s)
[ 58.760000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (N/A,
3000 mBm), (0 s)
[ 58.770000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A,
3000 mBm), (N/A)
[ 60.220000] br-lan: port 1(eth0.1) entered forwarding state
[ 60.740000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 60.740000] device wlan0 entered promiscuous mode
[ 61.360000] br-lan: port 2(wlan0) entered forwarding state
[ 61.360000] br-lan: port 2(wlan0) entered forwarding state
[ 61.370000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 63.360000] br-lan: port 2(wlan0) entered forwarding state
[ 71.550000] device wlan0 left promiscuous mode
[ 71.550000] br-lan: port 2(wlan0) entered disabled state
[ 72.170000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 72.200000] device wlan0 entered promiscuous mode
[ 72.210000] br-lan: port 2(wlan0) entered forwarding state
[ 72.210000] br-lan: port 2(wlan0) entered forwarding state
[ 72.560000] br-lan: port 2(wlan0) entered disabled state
[ 72.890000] br-lan: port 2(wlan0) entered forwarding state
[ 72.890000] br-lan: port 2(wlan0) entered forwarding state
[ 72.900000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 74.890000] br-lan: port 2(wlan0) entered forwarding state
}}}
Thanks!
--
Ticket URL: <https://dev.openwrt.org/ticket/17353>
OpenWrt <http://openwrt.org>
Opensource Wireless Router Technology
_______________________________________________
openwrt-tickets mailing list
[email protected]
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-tickets
